Dynojet Power Commander 6 Honda CBF1000F 2010-20211 Installation Guide

Dynojet Power Commander 6 Honda CBF1000F 2010-20211

PARTS LIST

1. 1 POWER COMMANDER 6
2. 1 INSTALLATION GUIDE
3. 1 USB CABLE
4. 2 DYNOJET DECALS
5. 2 POWER COMMANDER DECALS
6. 2 VELCRO STRIPS
7. 1 ALCOHOL SWAB

PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.

INPUT ACCESSORY GUIDE

OPTIONAL ACCESSORY INPUTS

Map (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can switch on the fl y between these two base maps when you hook up a switch to the MAP inputs. You can use any open/close type switch. The polarity of the wires is not important.

Shifter (Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2 by default.

Speed If your application has a speed sensor then you can tap into the signal side of the sensor and run a wire into this input. This will allow you to calculate gear position in the Control Center Software. Once gear position is setup you can alter your map based on gear position and setup gear dependent kill times when using a quick shifter.

Analog This input is for a 0-5v signal such as engine temp, boost, etc. Once this input is established you can alter your fuel curve based on this input in the Power Core software.

Launch You can connect a wire to either Input 1 or Input 2 and then the other end to a switch. This switch when engaged (continuity) will only allow the RPM to be raised to a certain limit (set in the software). When released, you will have full RPM.

WIRE CONNECTIONS

To input wires into the PC6 fi rst remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into the hole of the PC6 until it stops and then tighten the screw. Make sure to reinstall the rubber plug.
NOTE: If you tin the wires with solder it will make inserting them easier.

2 2010-2011 HONDA CBF1000F

INSTALLING THE POWER COMMANDER 6

1. Remove the seats.

2. Remove or prop the fuel tank up.

3. Lay the PC6 in the tail section and route the PC6 harness towards the front of the bike.

4. Route the PC6 harness from the right hand side of the bike to the left hand side. Go over the frame.
   Make sure the harness is routed so as to not be damaged by the fuel tank.

5. Unplug the stock wiring harness at injectors #1 and #2.

6. Plug the PC6 wiring harness in-line of the stock harness and injectors.
   PC6 harness:
   ORANGE: #1 cylinder
   YELLOW: #2 cylinder

7. To gain access to the #3 and #4 injectors remove the bolts that hold the thermostat to frame. Move the thermostat out of the way temporarily.

8. Unplug the stock wiring harness at injectors #3 and 4.

9. Plug the PC6 wiring harness in-line of the stock harness and injectors as in step 6.
   PC6 harness:
   GREEN: #3 cylinder
   BLUE: #4 cylinder

10. Locate the Throttle Position Sensor on the left hand side of the throttle bodies.

11. Unplug the stock connector from the TPS.

12. Plug the PC6 harness in-line of the stock wiring harness and TPS.

13. Using the supplied Velcro, secure the PC6 to the tail section. Make sure to use the alcohol swab to clean both surfaces before mounting.

14. Reinstall the fuel tank and seat.

Download the latest map fi les from our web site at dynojet.com/tunes.

2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 – 800-992-4993 – DYNOJET.COM © 2010-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED

References

• Powersports Vehicle Parts | Performance Ignition & Fuel Parts | Dynojet
• Tunes | Dynojet

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>