AMP Lighting ASDL-2014-B-BZ Solar Landscape Lighting Installation Guide

INSTALLATION & MAINTENANCE GUIDE
AMP® Solar Landscape Lighting
AMP® Solarium Brass Solar LED Deck Light
ASDL-2014-B-BZ

Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com

**** Important Safety Instructions: Read Before Installation

This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations.
Please note that these solar fixtures are equipped with built-in photocells, so they will not turn on until it is dark enough. These fixtures will also require plenty of sunlight to function properly. It’s best to have the fixture in an area where the sun will get to it at all times throughout the day and where no ambient lighting will affect the photocell at night. If your fixture is not functioning at night, be sure that the on/off button has been engaged. See step one for details.

**** Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
The lighted lamp is HOT!

WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

1. The lamp gets HOT quickly!
2. Do not touch the hot lens, guard or enclosure.
3. Keep the lamp away from materials that may burn.
4. Do not touch the lamp at any time. Use a soft cloth. Oil from the skin may damage the lamp.
5. Do not operate the luminaire fitting with a missing or damaged shield.

SAVE THESE INSTRUCTIONS

Package Contents

A. (1) Fixture Body
B. (1) Solar Panel Box
C. (1) Cover Plate
D. (2) Mounting Brackets
E. (4) Screws
F. (4) Wall Anchors

Product Dimensions

Test Solar Light

Press the ON/OFF switch on the back of the fixture body.
Place the solar light on a non-abrasive surface with the solar panel against the surface to test the fixture.
There will be a short delay for the fixture to light up. The fixture will light up when the solar panel is covered and turn back off when it is uncovered.
Now you can proceed to the next steps of installations knowing the fixture is in ON mode.
Two installation options are provided. Choose the one according to your installation environment:
Option 1: Plenty of sunlight.
Option 2: Lack of sunlight.

INSTALLATION OPTIONAL 1

Install Mounting Bracket

1. Place the mounting bracket onto the desired location and mark two points on the wall for the wall anchors.
2. Remove the mounting bracket. Drill the proper holes on the marks for the wall anchors by using an electric drill.
3. Push the wall anchors into the drilled holes.
4. Attach the mounting bracket onto the wall anchors and secure it with the screws. Tighten until snug with a screwdriver.

Place Fixture Body on to Mounting Bracket

Attach the bracket on the back of the fixture body to the mounting bracket on the wall.

INSTALLATION OPTIONAL 2

If the luminaire is going to be installed in a location where there is low sunlight, make sure it is still close to an area where there is plenty of sunlight for the solar panel to be installed separately.
Note: This distance must be less than 8.5 inches.

Install Mounting Bracket

1. Drill a .90” round hole through the desired mounting location.
2. Place the mounting bracket above the hole and mark two points on the wall using the two mounting bracket holes as guides.
3. Remove the mounting bracket and drill proper holes on the marks for the wall anchors using an electric drill.
4. Push the wall anchors into the drilled holes.
5. Attach the mounting bracket onto the wall anchors and secure it with screws. Tighten using a screwdriver.

Remove Solar Panel Box from Fixture Body

Slide the solar panel box off the top of the fixture body to remove it.

Disconnect Quick Connector

Disconnect the quick connector to separate the male connector from the female connector.

Install Cover Plate

Insert the cover plate onto the top of the fixture body.

Install Fixture Body onto Mounting Bracket

Pass the female connector and wire through the hole. Place the bracket on the back of the fixture body onto the mounting bracket.
Go to step 1 to install another mounting bracket onto the sunlit area for the solar panel. Pull the female connector to the other side then go the step 6.

Connect Quick Connector

Insert the female connector into the male connector and secure the cap to tighten the quick connector.

Install Solar Panel Box on to Mounting Bracket

Carefully tuck the quick connector and wire inside of the hole. Place the bracket of the solar panel box onto the mounting bracket.

Install Solar Panel Box on to Mounting Bracket

1. Using a screwdriver, remove the screws from the cover of the solar panel box.
2. Disconnect the quick connector.
3. Remove the battery pack out of the solar panel box and replace it with a new one.
4. Connect the quick connector to the new battery pack and place the cover back onto the solar panel box. Secure it with previously removed screws.

www.amplighting.com
customersupport@amplighting.com • 813.978.3900

Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
Specifications and product details are subject to change without notice.
© Copyright 2020, AMP ®Lighting, Lutz FL USA 33549 • All rights reserved.
customersupport@amplighting.com • 813.978.3900
www.amplighting.com
IS-ASDL-2014-B-BZ-ver3.pdf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>