AMP Lighting AHT-3517-B-BZ Low Voltage Landscape Lighting Installation Guide

Lighting
INSTALLATION & MAINTENANCE GUIDE
AMP® Low Voltage Landscape Lighting
AMP® TuscanPro Path & Area Light
AHT-3517-B-BZ
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
AMP® TuscanPro Path & Area Light
AHT-3517-B-BZ

Important Safety Instructions: Read Before Installation

This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty.

These instructions do not intend to cover all variations in installation, operation maintenance or mounting situations.

1. Make sure the power is turned OFF before installing or servicing this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from the pool, spa, or fountain.
3. This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL-listed wire connectors that are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire, or fitting.
6. The main low voltage cable is intended for shallow burial – less than 6 inches (152 mm).

**** Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS Lighted lamp is HOT!

WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

1. Turn off/unplug and allow to cool before replacing the lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard, or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch the lamp at any time. Use a soft cloth. Oil from the skin may damage the lamp.
6. Do not operate the luminaire fitting with a missing or damaged shield.
   SAVE THESE INSTRUCTIONS

Package Contents

A. (1) Hat
Parts Sold Separately
A. (1) Decorative Arm
Product Dimensions

customersupport@amplighting.com
• 813.978.3900

1. Remove Stem Top
   Loosen the stem top and remove it from the top end of the stem.

2. Install Decorative Piece (optional)
   

3. Insert the lamp with the correct wattage and type marked on the fixture label and push firmly into place.
   CAUTION: Do not exceed the maximum wattage marked on the fixture label.
   

4. Remove Washer and Finial
   Loosen the finial and remove the finial, coupler, and washer from the stem top.
   

5. Install Stem Top
   Place the stem top over the lamp and thread the stem top onto the stem. Hand tightens until snug.
   

6. Install Coupler to Hat
   Thread the coupler onto the hat and hand tighten until snug.

7. Install Hat
   Thread the hat onto the stem top and hand tighten until snug.
   

8. Install Stake
   Determine the desired location for mounting the stake mount. Hammer the stake into the ground until the flange of the stake is flush to grade. To avoid damage to the stake, place a board on top of the stake while hammering.
   Note: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel.
   

9. Install Stem to Stake
   Clear away an area in the ground at the wireway slot on top of the stake. Lay the luminaire pigtail into the wireway slot and secure the stem onto the stake. Tighten until snug.

10. Wire Connection
    Strip both leads from the luminaire. Using two-wire connectors (sold separately), connect the leads from the fixture to the main supply cable leads.

Install/Replace Bulb

Remove the hat and stem top to expose the lamp and replace it with the correct wattage and type marked on the fixture label. Then, reinstall the stem top and hat.
IMPORTANT: Lamps must be protected from moisture and dust at all times. Always reinstall the stem top and hat when removed.

Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
Specifications and product details are subject to change without notice.
© Copyright 2020, AMP ®
Lighting, Lutz FL USA 33549 • All rights reserved.
customersupport@amplighting.com
• 813.978.3900
www.amplighting.com
IS-AHT-3517-B-BZ-ver1.pdf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>