ATLANTIC 33906167 FreeStorm Gaming Desk Instruction Manual
- June 6, 2024
- Atlantic
Table of Contents
ATLANTIC 33906167 FreeStorm Gaming Desk
Assembly Tips
Become familiar with the instructions and all parts. Make sure that all parts are in the box and in good condition. Assemble the product on the open flat carton or a rug to protect the product and your floor. Some heavy products need a second person to assist in the assembly. Use of power tools is not recommended.
Care Instructions:
Use electrostatic dust cloths to clean furniture. Do not set hot or cold containers directly on the furniture surface.
Caution:
Never let children climb on furniture or play with furniture. Do not place a
weight heavier than the recommended load rating on the furniture surface.
Use care when moving furniture. Furniture can tip over if moved improperly.
Improper handling can result in cuts and lacerations. Do not install on a
sloping surface.
LED Remote Operation
-
Power/Standby
Press to turn the remote on or switch to standby. At power-on, the remote will return to the previous setting. -
Mode +/-
Switch to one of 22 dynamic modes or from static mode. -
Speed +/-
Increase (+) or decrease (-) dynamic mode speed. -
Color +/-
Switch to static from dynamic mode or between static colors. -
Bright +/-
Switch to static from dynamic mode and increase or decrease brightness.
-
Static Colors
Choose or change to one of 7 static colors.
SPECIFICATIONS
- Dynamic Modes 22
- Static Colors 7
- PWM Grade 256
- Brightness Levels 8
- Speeds 6
- Demo Modes 17
- Voltage 5-24 VDC
- Peak Current 3x4A
- Average Current 3x2A
- Remote Frequency 433.92 MHz
- Operating Distance <26 ft.
Parts List
-
Use Allen wrench (D) to attach all bolts. Lay left leg (4) on the floor and attach and tighten crossbars (1, 2, and 3) with two bolts (A) each. Lay assembly with crossbars on the floor. Attach and tighten right leg (5) to crossbars (1, 2, and 3) with two bolts (A) each.
-
Lay desktop upside down on a smooth surface.
Place the frame from Step 1 on the desktop (6)
and align the holes. Using the Allen wrench (D),
attach but do not fully tighten the six bolts (B).
Now working in a clockwise sequence tighten the
bolts, making sure the frame fits flush against the desktop (6). Attach braces (8) with two bolts (A) each.
-
Use Allen wrench (D) to attach and tighten all bolts. Attach the power strip tray (7) with four bolts (A). Attach the drink holder (9) with two bolts (A) on either side of the desk.
Lift the gaming desk upright as shown. Carefully press the USB hub assembly
(12) into the opening until it sits flush with the desktop. Insert USB
connector (12) into your laptop USB port. To power LEDS, insert USB connector
from LEDs (1) into USB hub (12) or into your laptop USB port. Attach tray
holder (11) with three screws (C) using a Phillips screwdriver. Slide tray
(10) onto tray holder (11) as shown.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
-
this device may not cause harmful interference, and
-
this device must accept any interference received, including interference that may cause undesired operation.
Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
Cautions: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>