onnline Outdoors Wall Ceiling Luminaire Onnwall Instruction Manual
- June 4, 2024
- onnline
Table of Contents
onnline Outdoors Wall Ceiling Luminaire Onnwall
SPECIFICATION PARAMETER
Model number|
COW492/ 4548171
UP-AL91-11-23W-AC3
|
COW493/ 4548172
UP-AL91-14-28W-AC3
---|---|---
Dimension(mm)| Ø275x59mm| Ø350x59mm
Power Consumption| 9W/14W/18W/23W| 14W/18W/23W/28W
Supply Voltage| 220-240V| 220-240V
Frequency| 50/60Hz| 50/60Hz
Color temperature| 3000K/4000K/5700K| 3000K/4000K/5700K
IP Rating| IP65| IP65
Lumen output| 3000 K| 4000 K| 5700 K
---|---|---|---
COW492| 9 W| 850 lm| 1050 lm| 880 lm
| 14 W| 1200 lm| 1450 lm| 1350 lm
| 18 W| 1480 lm| 1800 lm| 1700 lm
| 23 W| 2000 lm| 2450 lm| 2100 lm
COW493| 14 W| 1200 lm| 1500 lm| 1400 lm
| 18 W| 1650 lm| 1900 lm| 1750 lm
| 23 W| 2000 lm| 2400 lm| 2200 lm
| 28W| 2500 lm| 2800 lm| 2580 lm
Important safety instruction
To ensure correct function and safety, please read and follow all instruction
carefully before using the product,
Basic safety precautions should always be followed when installing, including
the following:
- Turn offer power supply before installation or before doing any maintenance, cleaning, changing the globe or adjustment to the fitting.
- Do not install any luminaire near the heat source.
- IP grade please refer to product label, only IP54 can be used in wet or damp locations,
- Do not exceed the nominal supply voltage or amperage ratings.
- All wiring and installation of the light fitting must adhere to local and national wiring rules.
- Take care not to pull any electrical wires during unpacking as this may damage the connection.
- Lay out all the components on a smooth surface and make sure three are no components missing before assembling.
- To avoid injury or damage to the fitting, please ensure that power leads and screws are secure before connecting the power.
- Please keep instruction for future reference.
Installation Procedure
Warning:
- S witch off before installation.
- S witch on only after complete installation and examination of the circuit
- P rofessional electrician for installation and maintenance only
Installation Procedure
Take out the lamp and accessories pack.
For round shape only: Unscrew the front frame, take the lamp cover apart by
rotating it in anticlockwise direction
Knock-in the plastic anchor into ceiling, fix the base.
For the AC wire into terminal block respectively. If with 3CCT or changeable
power function, choose preferred CCT or wattage by slide switch.
Plug the male and female connector. Align the hooks on the lamp cover with the
notch of the base, rotate the lamp cover clockwise until they match well.
Clip the frame into the base, rotate the frame clockwise until they match
well, fix frame with screw.
Installation finished, turn on the switch.
This symbol on products and or accompanying documents indicates that used and end of life electrical and electronic equipment should not be disposed of in household waste. For the proper disposal, treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your retailer upon the purchase of an equivalent new product. Disposing of this product correctly will help to save valuable resources and prevent any potential adverse effects on human health and the environment which could otherwise arise from inappropriate waste disposal and handling. Please contact your local authority for further details of your nearest designated collection point. Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation.
| This symbol
explains that the lamp is not suitable for covering with thermal insulating
material.
---|---
| Replaceable
(LED only) light source by a professional
| Replaceable
control gear by a professional
