Leap Frog LF2513, LF2513-2 2.8 Inch Pan and Tilt Video Baby Monitor with Night Light User Guide

Leap Frog LF2513, LF2513-2 2.8 Inch Pan and Tilt Video Baby Monitor with

Night Light

Important Safety Instructions

The applied nameplate is located at the bottom of the Baby Unit’s base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the Baby Unit above 2 meters.

4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or caregiver’s responsibility. This product could cease operating, and therefore you should not assume it will continue working correctly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby.

5. Do not use this product near water. For example, please do not use it next to a bathtub, wash bowl, kitchen sink, laundry tub, or swimming pool, or in a wet basement or shower.

6. CAUTION: Use only the battery provided. There may be a risk of explosion if the wrong type of battery is used for the Parent Viewer. The battery cannot be subjected to high or low extreme temperatures and low air pressure at high altitudes during use, storage or transportation. Disposal of a battery into a fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of the used battery according to the information in The RBRC seal.

7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
   Power adapter information:
   Baby Unit Output: 5V DC 1A; VTech Telecommunications Ltd.; Model: VT05EUS05100 Parent Viewer Output: 5V DC 1A; VTech Telecommunications Ltd.; Model: VT05EUS05100 Rechargeable battery information: Zhongshan Tianmao Battery Co. Ltd Li-ion battery, 3.8V 2100mAh 7.98Wh; Model: BP1763.

8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

9. For pluggable equipment, the socket outlet shall be installed near the equipment and shall be easily accessible.

10. Unplug this product from the wall outlet before cleaning.

11. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.

12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.

13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.

14. Do not overload wall outlets or use an extension cord.

15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.

17. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.

18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

19. You should test the sound reception every time you turn on the units or move one of the components.

20. Periodically examine all components for damage.

21. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time.

22. Children should be supervised to ensure that they do not play with the product.

23. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32oF (0oC) and 104oF (40oC).
2. Do not expose the product to extreme cold, heat, or direct sunlight. Do not put the product close to a heating source.
3. Batteries should not be exposed to excessive heat such as bright sunshine or fire.
4. Warning —Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove this tag.
5. Never place the Baby Unit(s) inside the baby’s crib or playpen. Never cover the Baby Unit(s) or Parent Viewer with anything such as a towel or a blanket.
6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances, and cordless telephones.

Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the pacemaker.
• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)
This LeapFrog product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available today.

What’s Included

Cable Management

Connect, Charge and Power On the Baby Monitor

Connect the Baby Monitor

Charge the Parent Viewer Battery

Notes:

• Before using the baby monitor for the first time, charge the Parent Viewer battery for 12 hours. When the Parent Viewer battery is fully charged, the battery icon becomes solid.
• The standby time varies depending on your actual usage time and the age of the battery.

The battery icon on the screen indicates the battery status:

Power On or Off the Baby Monitor

1. Slide the On/Off switch to ON to power on your Baby Unit.
2. Press and hold until the welcome screen appears. The green LINK LED light flashes.

Status Check
Once your Baby Unit and Parent Viewer are powered on and connected, your Parent Viewer displays video from Baby Unit, and the LINK LED lights steadily.

Positioning the Baby Monitor

Caution:
Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the baby’s crib or playpen.

Note:
To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers.

Caution:
The default volume of your Parent Viewer is level 3, and the maximum volume is level 5. If you experience a screeching noise from your baby monitor while positioning:

• Make sure your Baby Unit and Parent Viewer are more than 3 feet (1 meter) apart, OR
• Lower the volume of your Parent Viewer.

Overview

Parent Viewer

1. Link LED light
2. Power/ LCD Off
3. Menu/Select
4. Arrow Keys
5. Battery LED light
6. Talk/ Return
7. Microphone
8. RESET
9. Stand
10. Speaker
11. Power jack

Baby Unit

1. Light sensor
2. Camera
3. Infrared LEDs
4. Microphone
5. Night light
6. Night light control key
   • Press to turn the night light on or off.
   • Press and hold to adjust the night light brightness level.
7. Speaker
8. POWER LED Light
9. On / Off switch
10. Temperature sensor
11. Power jack
12. Wall mount holes
13. PAIR / Reset key
    • The Parent Viewer and Baby Unit provided are already paired.

The RBRC seal

The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives when taken out of service within the United States and Canada. The program provides a convenient alternative to placing used Li-ion batteries into the trash or municipal waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

California Energy Commission battery charging testing mode
This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy- conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the Parent Viewer is paired to Baby Units, the CEC battery charging testing mode is activated while it is powered off and charging.

Disclaimer and Limitation of Liability
LeapFrog and its suppliers assume no responsibility for any damage or loss resulting from the use of this handbook. LeapFrog and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this software. LeapFrog and its suppliers assume no responsibility for any damage or loss caused by the deletion of data as a result of malfunction, dead battery, or repairs. Be sure to make backup copies of important data on other media to protect against data loss.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
CAN ICES-3 (B)/NMB-3(B)

Caution:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Warranty:
Please visit our website at leapfrog.com for full details of the warranty provided in your country.

FCC and IC regulations

FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING:
Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

To ensure the safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The Baby Unit shall be installed and used such that parts of all persons’ bodies are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the Parent Viewer shall be held at least 1 in (2.5 cm) from your face.
This Class B digital apparatus complies with Canadian requirements: CAN ICES-3 (B)/NMB-3(B)

Industry Canada
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.
This product meets the applicable Innovation, Science, and Economic Development Canada technical specifications.

RF radiation exposure statement
The product complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The Baby Unit should be installed and operated with a minimum distance of 8 in (20 cm) between the Baby Unit and all persons’ bodies. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This equipment complies also with Industry Canada RSS-102 with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

Online Manual

Find the answer to your question on our knowledge-rich Online Manual. Get assisted at your own pace and learn what your monitor is capable of.

Scan the QR code to access the Online Manual or visit leapfrog.com/support.

Customer Support

Visit our Consumer Support website 24 hours a day at the United States:
leapfrog.com/support Canada: leapfrog.ca/support.

Call our Customer Service number from Monday to Friday
9 am – 6 pm Central Time:
United States & Canada:
1 (800) 717-6031.

Warranty

Please visit our website at leapfrog.com for full details of the warranty provided in your country.

Technical Specifications

• Frequency Control Crystal-controlled PLL synthesizer
• Channels 32
• Frequency
  • Baby unit: 2405 – 2475 MHz
  • Parent unit: 2405 – 2475 MHz
• LCD 2.8” Color LCD (QVGA 320×240 pixel)
• Nominal effective range: Maximum power allowed by FCC and IC. The actual operating range may vary according to environmental conditions at the time of use.
• Power requirements:
  • Parent unit: 3.8V, 2100mAh Li-ion, 7.98Wh Li-ion battery.
  • Baby unit power adapter: Output: 5V DC @ 1A.
  • Parent unit power adapter: Output: 5V DC @ 1A.

Specifications are subject to change without notice.
© 2022 LeapFrog Enterprises, Inc.
a subsidiary of VTech Holdings Limited.
All rights reserved. 08/22. LF2513_QSG_V1.

References

• LeapFrog Customer Support | Help & Support For LeapFrog Products
• Kids Learning Games | Educational Toys & Kids Tablets | LeapFrog
• LeapFrog Customer Support | Help & Support For LeapFrog Products
• Legal | LeapFrog

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>