SCANSTRUT SC-CW-07F ROKK Wireless Charger Instruction Manual

SC-CW-01F, SC-CW-02F, SC-CW-07F
Instruction Manual

Electrical information & installation instructions.
Issue 5
READ THESE INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.

The product must be installed in accordance with the instructions provided. Failure to do so could result in personal injury, damage to your vessel/vehicle, and/or product failure. Scanstrut recommends installation is carried out by a qualified electrician. No liability is accepted for damage and/or injury caused by incorrect installation.
WARNING:
This product is to be fitted to a 12V DC or 24V DC battery/power source only.
The power supply must be switched off before installation.
An appropriate fuse or circuit breaker must be used inline between the battery/power source and the product.
Check for the correct polarity of all wiring before switching the power on.
This product may contain high voltages. Do not tamper with the product. This product is NOT approved for use in hazardous/flammable atmospheres.
Do NOT install in a hazardous/flammable atmosphere e.g. engine rooms. Before drilling any holes, ensure the area behind the mounting location is clear of wires, fuel and all other hazardous objects.
Ensure any holes cut will not significantly weaken the structure of the surface If the product needs to be mounted outside, it must be mounted in a location safely above the waterline, where it is not at risk of being submerged. The product cannot charge through a metallic surface.
CAUTION:
The product is specifically for the charging of 01 compatible devices.
The cable must be retained and not interfere with mechanical systems.
This product contains no user-serviceable components. Do NOT attempt to repair or alter the product in any way.
The high friction top surface does not ensure the device will not slip during extreme operating environments such as high acceleration and deceleration.
If a phone case that is thicker than 3mm is used the device may not charge.
When used in a high ambient temperature/direct sunlight the product may temporarily shut down, this is a safety feature of the electronics.
The IP rating is only valid if correctly installed using the instructions. When selecting a mounting location, avoid places exposed to heat-radiating appliances and poorly-ventilated areas

EMC INSTALLATION GUIDELINES:

Scanstrut products conform to Electromagnetic Compatibility (EMC) regulations, to ensure that electromagnetic interference between equipment is minimized.
Correct installation is required to ensure that electromagnetic interference is kept to a minimum.
WIRING: When extending the cable from your battery/power source to the product, ensure there is a minimum of 10V being provided to the product continuously. We recommend a wire gauge of 18AWG (0.82mm2) for any length of cable extension.
This schematic is to illustrates how the product should be connected to a 12V DC or 24V DC battery/power supply.
ENVIRONMENTAL PROTECTION : Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
IMPORTANT:
Scanstrut Ltd. accepts no responsibility for any injuries or other damages arising from the use of their products in any circumstances.

WARRANTY:

A 2 year, the non-transferable warranty covers this Scanstrut product only and not any devices that are mounted in it or on it. No warranty is given for users’ devices and users expose their devices to hazards, known or unknown, at their own risk.

FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance between 20cm of the radiator and your body. FCC ID: 2APUP- SC-CW-01 F
Scanstrut Ltd declares the product ‘ROKK Wireless Hidden 10W’ SKU: SC-CW-01F is in compliance with EMC CE-RED Directive (2014/53/EU) & standard EN 62368. The CE certificate of conformity can be found at www.scanstrut.com/uWcompliance.

Technical information.

For the latest tech info visit: www.scanstrut.com/rokk- wireless
Scanstrut Ltd
5 Dart Business Park,
Cyst St. George, Exeter
EX3 0QH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>