Lisen H513 2-in-1 Mag-Safe Wireless Charger Stand Instruction Manual

June 6, 2024
Lisen

Lisen H513 2-in-1 Mag-Safe Wireless Charger Stand

Thanks for choosing Lisen! To bring you a fantastic experience, please read the manual before using.

Product Structure

Specifications

Name 2-in- Mag-Safe Wireless Charger Stand
Model H513
Material Aluminum Alloy; ABS+PC
Input 5V==2.4A 9V==2A l2V==2A 15V=2A
Output Phone Charging Center: 5W/7.5W/10W/l5W

Earphone Chargfng Center: 5W/2.5W
Maximum Output Power| 15W+5W (with 30W Adaptor)
Product Size| 110x110x184.14mm
Weight| 255g

Indicator Light Description

STATUS INDICATOR LIGHT
Connected to power supply The white light is on and keep for 5s, then it will

be off
Mobile phone wireless charging is active| Right white is breathing
TWS earphone wireless charging is active| Left white is breathing
Mobile phone wireless charging is over Current,short- circuit foreign object detect| Right white light is flashing to warn
TWS earphone wireless charging is over current,short- circuit foreign object detect| Left white light is flashing to warn

Applicable Devices

  1. Support wireless charging for earphone: Airpods 2; A rpods Pro;
  2. Support wireless charging for cellphone: iPhone 12 Pr Max; iPhone 12 Pro; iPhone 12; iPhone 12 mini.

Cautions

  1. Bending angle: the stand can only be adjusted between 7° and 50°, please take care not to pull forcibly, which may cause damage to the stand;

  2. This product only supports original earphone and Magsafe phone case purchased from regular channels;

  3. ① Charging for earphone: only supports charging for earphone case up to 3MM, if beyond please replace or remove the case before use;

    ② Powering your phone: The product only supports iPhone 12 Pro Max/ iPhone 12 Pro/ iPhone 12/ iPhone 12 mini without case, and these devices with original cases that support magsafe. For other brands of phone cases, please stick the included magnetic sheet

  4. If you use a non-magsafe phone case, you need to stick the magnetic sheet, the operation method is as follows:

    ① Align the magnetic sheet locator up and down and place it on the back of the phone/phone case;

    ② AT ear off the protective film of the magnetic sheet and stick it on the center of the magnetic sheet locator;

    ③ The magnetic sheet and the built-in magnet of the phone attract each other, which can assist in positioning.

Note: Liquid silicone cases, oil-painted cases and cases with uneven surfaces are not suitable for the magnetic sheet.

  1. Earphone positioning: align the earphone in the center and put it in the earphone charging center;

  2. If you need to take off the phone, hold the phone and press down, and lift the top of the phone, as shown in the figure;

  3. The matching charging cable is a USB C – USB A+C charging cable, depending on your adapter;

  4. Warning: If the back of the phone has a metal material such as a finger ring stand or car mount patch, please remove it before using this wireless charging stand;

  5. It is normal for the product to heat up slightly during use, if there is serious heating, please suspend use and contact our after-sales mailbox.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure: A distance of 20 cm shall be maintained between the antenna and users, and the transmitter may not be co-located with any other transmitter or antenna.

FCC ID:2AW73-H513

After Sale Service

Lisen always dedicates to bring great shopping experience for each customer. Please feel free to contact us if you have any questions.

365 DAY
Worry- free
365-Day Warranty

24 HOURS
24/7 Easy- to- Reach Support
Email support@lisen.us, get connection within 24 hours.

| AMZLAB GmbH
Louoenhof 23, 45326 Essen
---|---
| UKCA SERVICE LTD
21 Ellesmere Avenue, Worsley,Manchester.UK,M28 OAL

Shenzhen Xiangdangwen Technology Co., Ltd
Address: 106, 1/F, No.313-4 Building, Huachang Road, Langkou Community,Dalang Street, Longhua District, Shenzhen, China Copyright©2021Lisen, All rights reserved

Manufacture: Huizhou Yimai Electronics Technology Co., Ltd.
Address: 3rd Floor, Building B, Huakai High-tech Industrial Park, Electronic City Road, Longxi Street, Boluo County.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals