LISEN 2E749 Car Magnetic Wireless Charging Stand User Guide
- June 13, 2024
- Lisen
Table of Contents
2E749 Car Magnetic
Wireless Charging Stand
User Guide
Thanks for choosing Llsen! To bring you a fantastic experience, please read the man-ual before using.
ACCESSORY LIST
PRODUCT PARAMETER
NAME
CAR MAGNETIC WIRELESS
CHARGING STAND
MODEL
2E749
MATERIAL
ABS/PC
INPUT
5V=2A 9V=2A 12V=15A
OUTPUT
5W/7.5W/10W/1SW tl
SIZE
60MM117MM35MM
WEIGHT
165G
APPLICABLE POSITION
AIR OUTLET
SUPPORT BAR ADJUSTMENT STROKE
10MM
HOOK TELESCOPIC STROKE
30MM
OUTLET BLADE WIDTH
11-28MM
THICKNESS OF AIR OUTLET BLADE
<4.5MM
PRODUCT DESCRIPTION
1.The product is equipped with LED light ring, LED light source rotates around
a circle when the power Is turned on, the LED light Is always on when the
power is normally tur- ned on.
2.Put into the mobile phone since the LED light effect off, take away the
phone after the LED re-lighting,
COMPATIBLE DEVICES
- Headphones: Airpods pro (with magsafe battery compartment)/‘Ai- rpods pro 2nd generation.
- iphone 12/13/14 series bare phone /phone case with magsafe function I /third party case without magsafe need to increase the magnetizer .
- With wireless charging does not support magsafe mobile phones, n- eed to use the magnetlizer
- Without wireless charging mobile 7 phone, need to use the magnetizer C Conly the car mount function, no w- C ireless charging function)
INSTALLATION STEPS FOR THE U- SE OF AIR OUTLET HOOK CLIPS.
Loosen the fixing nut in a counter- clockwlse directionIn扭rt the swivel ball into the boltTighten the nxl ng nut Turn the hook clip adjustment knob counter- clockwise to adjust the hook length to the maximum.
- If the support ring is obstructed, you can rotate the support ring to flt your air outlet.
- If yourralr, vent is smBII in size and 1t is inconvenient to install the support ring, you do not need to use the support ring (When there is no support ring In the attached pie-ture)snap the hook clip Into the air out- l&t of Iha car and turn th& hook cllp adjustment knob to lock the blade.
To remove, loosen the hook and clip adjustment knob and detach the holder from the blade.(The blades should be kepi horizontal so that Iand to the surface of the air outlet) hey are perpendicular to each other
When adjusting the angle of use, slightly loosen the nut and adjust it to a
comfortable angle before tightening the nut. Hint: The uneven surface of mobile phone cases, liquid
silicone cases, oil-painted cases and fabric leather cases are not suitable
for this magnetizer.If your case does not have the
mag safe function, please follow the ste ps below to attract the magnetic
sheat to achieve the magnetic suctian function first.
Place the magnetic plate locator on the back of the phone/case, aligning the
edges of the phone to ensure the top and bottom scale/left and right scales
are the same; remo ve the protective film from the ma gnetlc plate and strck
It to the cen tre of the magnetic plate locator.
INSTALLATION STEPS
Tutorial on the use of the lead magnet:
- open the tissue pack and wipe the back of the phone/case with a damp tissue first, then dry it with a dry tissue.
- f the mobile phone (case) is made of glass or if you do not want to slick the magnet attractor directly to the mobile phone (case), you can use the PE film first, peel off the PE film and stick it on the back of the mobile phone/case in the centre.
- Place the film on the back of the phone. Observe that the position Ing film has the same symmetrical edge to ensure that the ring Is posoned In the mlddle of the phone.
- Remove the protective film from the back of the ring. Place the filmin the middle of the ease and press gently with your hand. Make suret hat the ring is positioned in the middle of the film. Remove the positi
oning film; pressi torabout 5 seconds and leave it for 6 hours.
NOTE
- About using non-standard car charger: please QC3.0 or PD18Wor above.
- Metal accessories (iron pieces, finger clasps) or credit cards cannterfere with charging. Cases cont aining metal, such as Pitaka, Evutec and Spigen QNMP, will trigger fore ign object detection and interrupt charging.
- Using the phone for GPS naviga tion or listening to music while cha rging can significantly affect the charging speed. When using GPS applications, the power consumption may be higher than the charging speed
- It is normal to have slight healing during the use of the wireless charger, if you encounter serious heati ng, please suspend the use and co ntact our after-sales mailbox.
PRODUCT WARNINGS
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful inter压renee to radio communications. However, there is no guarantee that interference will not occur In a partlcular lnstallatlon .If this equipment does cause harm ful interference to radio or television reception, which can be determ i ned by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following meas ures:
- Reorient or relocatl! the receiving antenna.
- Increase the separation between the equipment ancl receiver.
- Connect the equipment into an utlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experie need radio/TV technician for help This equipment must be installed and operated with a minimum distance of 15 cm between the radiator and user body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>