LISEN 2E789 15W Magnetic Car Mount Charger User Manual

LISEN 2E789 15W Magnetic Car Mount Charger

Thanks for choosing Lisen! To bring you a fantastic experience, please read the manual before using it.

PRODUCT ACCESSORY LIST

PRODUCT STRUCTURE

PRODUCT PARAMETERS

• PRODUCT MODEL 2E789
• MATERIAL ABS+PC / ZINC ALLOY
• INPUT 5V – 2A 9V-2A 12V-1,5A
• OUTPUT 5W/7.5W/10W/15W
• DIMENSIONS 68x59x23.6mm
• WEIGHT 266g

COMPATIBLE DEVICES

1. Headphones: Airpods Pro (with ma- gsafe battery compartment) / Airpods pro 2nd generation.
2. iPhone 12/13/14 series naked/with magsafe case/third party case without magsafe case requires additional ma- gnetizer.
3. With a wireless charger that does not support Magsafe phones, you need to use a magnetizer.
4. Without a wireless charger or phone, need to use a magnetizer (only car mount function, no wireless charger function).

INSTALLATION STEPS FOR THE BRACKET

1. Before installing the bracket, please ensure the desired placement for adhesive use, to avoid the need for dismantling and reapplying the bracket due to an unsuitable position or angle (reapplying with adhesive may result in instability or detachment risks).
2. Open the wet wipes and clean the intended adhesive area to ensure there is no dust or foreign particles that may affect the adhesive’s effectiveness.
3. After wiping with the wet wipes, use a dry cloth to wipe the cleaned area to ensure it is dry.
4. Peel off the protective film on the adhesive surface at the bottom of the bracket. Place the bracket firmly on the cleaned area and press it down firmly.
5. Allow it to rest undisturbed for 12 hours before normal usage. (During the bracket installation process, do not touch the adhesive with hands or other objects after removing the adhesive film, as it may affect the adhesive’s effectiveness).

GUIDE DISK INSTALLATION PROCEDURE

1. Tutorial on the use of the magnetic lead sheet.
   Tips: the uneven surfaces of mobile phone cases, liquid silicone cases, oil spray-ed cases, and fabric, and leather cases are not suitable for this magnetizer.

2. If your case does not have the mag-safe function, please follow the steps below to use the magnetic pad to achieve the magnetic suction function.

3. Place the magnet locator on the back of the phone/case, aligning the edges of the phone and making sure the top and bottom/left and right scales are the same; remove the protective film from the magnet and stick it to the center of the magnet locator.

NOTES

1. About using a nor-standard car charger: please use QC3.0 or PD18W or above.
2. Metal accessories (iron pieces, finger rings) or credit cards can interfere with charging. Cases containing metal, such as Pitaka, Evutec and Spigen QNMP, will trigger foreign object detection and interrupt charging.
3. Using the phone for GPS navigation or listening to music while charging can significantly affect the charging speed. When using GPS applications, the power consumption may be higher than the charging speed.
4. It is normal for the wireless charger to heat up slightly during use. If you experience severe heating, please suspend use and contact our after-sales email

FCC WARNING STATEMENT

This equipment generates uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving filler lid.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment must be installed and operated with a minimum distance of 15 cm between the radiator and the user body.

AFTER SALE SERVICE

Lisen is always dedicated to bringing a great shopping experience for each customer. Please feel free to contact us if you have any questions.

Shenzhen Xiangdangwen Technology Co., Ltd,

• ADDRESS: 106, 1/F, No.313-4 Building Huachang Road, Langkou Community Dalang Street Longhua District, Shenzhen, China.
• MANUFACTURE: Huizhou Vimal Ele- Conics Technology.
• ADDRESS: 3rd Floor, Building B, Hu- akai High-tech Industrial Park, Electronic CityRoad, Longxi Street, Boluo County.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>