novostella NTF71 Smart LED Flood Light User Guide

novostella NTF71 Smart LED Flood Light

Thank you for ordering from Novostella. Set-up is easy and takes only a few minutes by following the instructions.

Part One – How to install the light?

Warning

1. Please check if the light and the parts are intact before installation.
2.  Make sure to cut off power before installation.
3.  Please do not place this light in corrosive conditions.
4.  If there is any damage to the cord, please cut off the power and stop using it immediately.
5. Please do not retrofit the light within the warranty period.
6. To ensure the light works properly, please use the voltage indicated on the packing.

Parameters

Components

Note: Cord – type Y attachment.
For type Y attachment: If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer of his service agent or a similar qualified person in order to avoid a hazard.

Dimension

Installation

Step A: According to the spacing of two screw bits on the bracket, drill two holes on the mounting panel.

Note: Maximum mounting height is over 5m.

Step B: Aim the bracket at the holes and fix it with two bolts.
Step C: Adjust the lighting direction up or down as per your need and plug in to power the light on.

Note:

01 Make sure that the distance between the light and the object being lits is more than 1 meter, so as to avoid high temperature caused by short distance.
The light source of this Luminaire is not replaceable.
Limitation of Indoor and Outdoor Use

1. This light is waterproof and damp proof. It is protected against the rain, but it cannot be immersed in water.
2. The mounting position of this light should be able to bear at least 10 times as heavy as the light.
3.  This light should be used in condition that is good for heat dissipation. Its working temperature should be less than 45°C Too high the working temperature will cause serious lumen depression and affect lifespan of the light.

FCC ID: 2AWONNTF71
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Information to the user:

• (For a Class A digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual:
  Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

•  For a Class B digital device or peripheral, the instructions furnished the user shall include the following or similar statement, placed in a prominent location in the text of the manual:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. In cases where the manual is provided only in a form other than paper, such as on a computer disk or over the Internet, the information required by this section may be included in the manual in that alternative form, provided the user can reasonably be expected to have the capability to access information in that form.

Part Two – How to pair the light to Smart Life app?

Before starting the paring, please make sure to turn on the Bluetooth on your phone, and connect to the Internet.
Step A: Smart Life app installation
Please choose either way below to download and install the app.

1. As per your phone system, choose the QR code to scan.
   

2. Search keyword ‘Smart Life’ in Apple Store of Google Play.

Step B: Create an account on Smart Life and login.
Note: Please keep your account and password in mind for Alexa or Google Assistant APP pairing later.

Step C : Add the light to Smart Life App

1. Tap ‘+’ button on top right corner to add devices. Tap ‘Lighting’, then choose ‘Light Source (BLE)’ to add the lights.
   

2. Power on the light with your own switch. Repeatedly turn on-off-on-off-on-off-on switch to activate the light into rapid blinking status (about 0.5s per blink). Please make sure to keep an interval over 2 seconds between each turn-on and turn-off. Then click the ‘Next’ button on this page. Find the lighting devices and click ‘+’.
   

3. Give a name to the light.
   Note: A simple name is recommended.

4. The named light will be shown on the app homepage. Now you can control the light (turn on/off, change colors, adjust brightness etc..) with Smart Life on the setting page. Turn on or off the light by tapping the bulb icon.

How to group the lights?

Make sure all the lights have been paired to “Smart Life” app, then group the lights by following these steps.

1. Choose any light on the app, click the edit button on the top right corner, then click “Create Group” .
2. Choose the lights you want to group from the device list and rename the group.

Part Three – How to connect the lights to Internet, and control with

Amazon Alexa and Google Assistant?

If you want to connect the lights to Internet, and control with Amazon Alexa and Google Assistant, you can easily expand the smart flood lights with our Hub accessory (sold separately).
Please click below link to purchase the Hub accessory from our shop:
US: https://www.amazon.com/dp/B08WXBLN3G
UK: https://www.amazon.co.uk/dp/B08WKWMMFR
After you get the Hub accessory, please follow below steps to setup:

Step A: WiFi connection, pair the Hub to Smart Life App.
Please turn on the WiFi on your phone. The hub only supports 2.4GHz WiFi network, not 5.0GHz. Please make sure your working network is 2.4GHz and your router has disabled the MAC filter.
** It is strongly recommended to place the hub to somewhere that is between the lighting devices and the router, and make sure it responds well to the WiFi signal.

1.  Tap ‘+’ button on top right corner to add device. Tap ‘Gateway Control’, then choose ‘Wireless Gateway (BLE)’ to add the hub.
   

2. Plug the hub into a socket. Long press the power button on the hub will the indicator lights rapidly blink, tap the ‘Next ’ button, then click ‘+’ button to add the hub.
   

3. Choose your WiFi network, enter your password, and tap the ‘Next’ button. Give a name to the hub and tap the ‘Done’ button.
   

Step B : Add the lights to the Hub.
Please make sure all the lights have been paired to ‘Smart Life’ App first. Choose the hub on the app, click the ‘add device by list’ button, select all the lights, and click the ‘Confirm’ button.

How to control the light with Amazon Alexa?

How to control the light with Google Assistant?

References

• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Alza.sk – rýchly a pohodlný nákup odkiaľkoľvek | alza.sk
• NOVOSTELLA WiFi Gateway Wireless Smart Bridge, Smart Hub, Smart Home Bridge, APP Remote Control, Voice Control, Works with Alexa Google Home, Connects Bluetooth Smart LED Flood Lights : Amazon.co.uk: DIY & Tools
• NOVOSTELLA Smart Wireless BT Mesh Hub Smart LED Flood Lights, Compatible with Amazon Alexa, Google Assistant for Remote Control, Voice Control

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>