SCANSTRUT SC-CW-04F Rokk Wireless Active Charging Cradle f/Phone Instruction Manual

ACTIVE 10W.

Electrical Information & Installation Instructions.
Issue 2

SC-CW-04F
IMPORTANT:

READ THESE INSTRUCTIONS BEFORE INSTALLING THE PRODUCT.

For latest tech info visit: www.scanstrut.com/rokk- wireless

Technical information

Parts list:

Tools required:

Soft Material
E.g plywood| 2mm ((5/64″)
Hard Material
E.g Fiberglass acrylic, hardwood| 2.5mm (3/32″)

Installation instructions.

1. Retain installation jig to use in step 2.

| 2. insert the installation jig.

---|---
3. Ensure there is sufficient clearance in chosen installation area.

| 4a. Ensure installation area is flat.

4b. Ensure ROKK Active is vertical.

| 5. use drilling template to drill ø6mm (0.24″) cable hole and x4 pilot holes (see tools required table)

6. • Feed cable through the hole.
• Apply sealant to x4 screws.
• Screw product in place.
Remove installation jig.
| 7. Connect wires to 12/24V supply, ensuring a waterproof connection. Fuse according to input voltage and current.

Drilling Template: Warning Check Scale

Smart LED light guide:

Solid red
Product has power and ready to charge.

Solid green
Product charging.

Flashing red

1. Foreign object detection: metallic object placed on top that is not Qi compatible. or
2. Thermal cutout: internal temperature is too high/ low.
   Wait for product to return to operating temperature.

Flashing green/red
Input current is too low.

This product is designed to securely mount phones under normal usage conditions. The end-user is entirely responsible for conditions in which their device is used. See WARRANTY section for further details.
Scanstrut recommends installation is carried out by a qualified electrician. No liability is accepted for damage and/or injury caused by incorrect installation.

WARNING:
This product is to be connected to a 12V DC or 24V DC battery power source only.

The power supply must be switched off before installation.
An appropriate fuse or circuit breaker must be used between the battery / power source and this product. Check for correct polarity of all wiring before switching the power on.

This product may contain high voltages. Do not tamper with the product.

This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere e.g. engine room.

Before drilling any holes, ensure the area behind the mounting location is clear of wires, fuel and all other hazardous objects.
Ensure any holes cut will not significantly weaken the structure of the mounting surface.

If the product needs to be mounted outside, it must be mounted in a location safely above the waterline, where it is not at risk of being submerged.

Full strength not achieved until product is installed

IN EXTREME USAGE ENVIRONMENTS PERFORMANCE MAY VARY.

CAUTION:
The product is designed specifically for the charging of Qi compatible devices.
The cable must be retained and not interfere with mechanical systems.
This product contains no user serviceable components. Do NOT attempt to repair or alter the product in any way.
This product will charge through non-metallic phone cases up to ~3mm thick. Phone cases may alter overall charge performance.
When used in a very high/low ambient temperature/direct or prolonged sunlight the product may temporarily shut down, this is a safety feature of the electronics.
The IP rating is only valid if correctly installed as per these instructions and on a perfectly flat, non-porous, smooth surface.
When selecting a mounting location, avoid places exposed to heat-radiating appliances and poorly ventilated areas.

EMC INSTALLATION GUIDELINES:
Scanstrut products conform to Electromagnetic Compatibility (EMC) regulations, to ensure that electromagnetic interference between equipment is minimised.
Correct installation is required to ensure that electromagnetic interference is kept to a minimum.

WIRING:
When extending the cable from battery/power source to the product ensure there is consistently a minimum of 10V being provided to the product. A wire gauge of 18AWG (0.82mm2) is recommended for any length of cable extension.

The electrical schematic is to illustrate how the product should be connected to a 12V DC or 24V DC battery/power supply.

ENVIRONMENTAL PROTECTION:
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.

IMPORTANT:
Scanstrut Ltd. accepts no responsibility for any injuries or other damages arising from the use of their products in any circumstances.

WARRANTY:
A 2 year, non-transferable warranty covers this Scanstrut product only and not any devices that are mounted in it or on it. No warranty is given for users’ devices and users expose their devices to hazards known or unknown, at their own risk.

USER GUIDE:

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.

FCC ID: 2APUP-SC-CW-04F

Documents / Resources

| SCANSTRUT SC-CW-04F Rokk Wireless Active Charging Cradle f/Phone [pdf] Instruction Manual
SC-CW-04F, SCCW04F, 2APUP-SC-CW-04F, 2APUPSCCW04F, SC-CW-04F, Rokk Wireless Active Charging Cradle f Phone, SC-CW-04F Rokk Wireless Active Charging Cradle f Phone
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>