Kruger Matz KM0103.1 Car Radio/Receiver Owner’s Manual

June 6, 2024
Kruger Matz

Kruger Matz KM0103.1 Car Radio Receiver-logo

Kruger Matz KM0103.1 Car Radio/Receiver

Kruger Matz KM0103.1 Car Radio Receiver-product

PRECAUTIONS

  • Choose the mounting location where the unit will not interfere with the normal driving function of the driver.
  • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
  • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
  • Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
  • Install the unit where it does not get in the driver‘s way and cannot injure the passenger if there is a sudden stop. Like an emergency stop.
  • Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, form the heater, or where it would be subject to dust, dirt or excessive vibration. Do not expose this equipment to rain or moisture.

DIN FRONT-MOUNT (Method A)

Installing the unit

Kruger Matz KM0103.1 Car Radio Receiver-1

  1. Dashboard

  2. Holder
    After inserting the holder into the dashboard, select the appropriate tab according to the
    thickness of the dashboard material and bend them inwards lo secure the holder in (Fig. 1) place.

  3. Screw

Kruger Matz KM0103.1 Car Radio Receiver-2

  1. Dashboard

  2. Nut (5 mm)

  3. Spring Washer

  4. Screw (5x25rnm)

  5. Screw

  6. Strap
    Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle.

  7. Plain Washer

Kruger Matz KM0103.1 Car Radio Receiver-3

  1. Frame
  2. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When reattaching the frame, point the side with a groove downwards and attach it.)
  3. Lever
    Insert the levers supplied with the unit into the grooves at both sides of the unit and shown in figure until they click. Pulling the levers makes possible to remove the unit from the dashboard.

DIN REAR-MOUNT (Method B)

Installation using the screw holes on the sides of the unit Fastening the unit to the factory radio mounting bracket:

Kruger Matz KM0103.1 Car Radio Receiver-4

  1. Select a position where the screw holes oft he bracket and the screw holes of the main unit become aligned (are fitted), and tighten the screws at 2 places on each side. Use either truss screws (5 x 5mm) or flush surface screws (4 x 5mm)
  2. Screw
  3. Dashboard or Console

INPUT THE SD CARD
The SD oblique angle keeps Rightward exposure, put into the SD slot and press it again to eject.

Kruger Matz KM0103.1 Car Radio Receiver-5

WIRE CONNECTION DIAGRAM

Kruger Matz KM0103.1 Car Radio Receiver-6

FRONT PANEL LAYOUT

Kruger Matz KM0103.1 Car Radio Receiver-7

  1. Power / Mode Button
  2. Release Button
  3. Volume / Sel Button
  4. Mute / Hangup a call Button
  5. Display Button
  6. LCD Display
  7. Flashing LED
  8. Reset Button
  9. Band switch / lD3 select / Receive a call
  10. Tune Seek & Track forward Button
  11. Tune Seek & Track reverse Button
  12. Automatically memory storing
  13. Play/Pause & Preset Button 1
  14. Intro & Preset Button 2
  15. Repeat & Preset Button 3
  16. Random & Preset Button 4
  17. Preset Button 5
  18. Preset Button 6
  19. Eject knob
  20. CD slot
  21. Remote Control Sensor
  22. USB connecter
  23. SD/MMC Slot
  24. AUX IN JACK

GENERAL OPERATIONS

FRONT PANEL RELEASE
Press REL button (2) to detach the removable front panel.

SOUND ADJUSTMENT
Turn on (3) can adjust the desired volume quality. Press SEL button (3) will change in the following order. Option:

Kruger Matz KM0103.1 Car Radio Receiver-8

VOLUME
Rotating this knob, you can adjust VOL/BASS/TREB/BAL/FAD . To select the functions, press the VOL knob shortly until the desired functions are shown on the display. Increase or decrease the volume by turn the VOL knob right or left. These buttons can be used to adjust the BASS, TREBLE, BALANCE and FADER.

BASS
Press VOL/SEL button (3) one time. Adjust bass level by using VOL/SEL (3) knob.

TREBLE
Press VOL/SEL button (3) two times. Adjust treble level by using VOL/SEL(3) knob

BALANCE
Press VOL/SEL button (3) three times. Adjust sound balance between left and right speakers by using VOL/SEL (3) knob.

FADER (optional)
Press SEL button (3) four times. Adjust sound balance between front and rear speakers by using VOL/SEL (3) knob.

SELECT MENU
Press VOL/SEL button for several seconds, selecting menu is activated as cyclical mode of following function for use’s selection:

Kruger Matz KM0103.1 Car Radio Receiver-13

RDS (RADIO DATA SYSTEM) OPERATlON

AF :Alternative Frequencies

  • Setting RDS Mode Press AF button (20) and release immediately to switch on or off RDS mode. Whenever RDS is switched on, symbol “AF” appears on the display. AF / REG AF
  • AF I REG key directs the activation of AF SEARCH.
  • AF indicator is displayed when AF is ON, AF search is activated when reception is bad.
  • During FM MODE, when AF is ON, SEEK, SCAN, AUTO, MEMORY function can only receive and save RDS program. However, when Italy option is in use, regardless of RDS programs that satisfy SD LEVEL Can be received and saved.
Indicator Condition
AF ON AF ON MODE, RDS information is received.
AF OFF AF OFF MODE
AF blink AF ON MODE, RDS information is not received.

REGION

  • AF MODE is converted to REGION ON / OFF MODE when SEL is pressed for longer 3 sec.
  • ON : Pl CODE is checked when AF CHECK in progress.
  • OFF: PI CODE and COVERAGE AREA is not checked when AF CHECK in progress.

PTY RADIO MODE

  • Press SEL key, PTY flashing on display when select PTY. If there are no keys entered for 2 seconds, previously selected PTY is searched. During 1 LOOP, if desired PTY is not found, NO PTY is displayed.
  • 2 program types are SPEECH and MUSIC. By pressing PTY once, MUSIC is entered. When PTY is pressed the second time, SPEECH is entered. M1~M6 keys can be used to select the desired program type.

TA
TA button is operated as follows:

  • Press SEL enter TA, TA is turned ON / OFF and TA indicator is displayed. When traffic announcement is transmitted, regardless of the mode, traffic announcement is received.
  • If VOLUME LEVEL is below 20, VOLUME LEVEL is raised to 20, and returns to its previous mode and volume level when the traffic announcement is over.
  • If volume is adjusted during traffic announcement, only the previous volume is valid.
  • When TA is on, SEEK, SCAN, AUTO MEMORY function can be received or saved only when traffic program identification code has been received.
  • When TA is ON, traffic program identification code is not received during specified time.
  • TA ALARM : NO TA/ TP is displayed and alarm is set off.
  • TA SEEK : TA SEEK is activated.

BLUETOOTH

  1. Pairing connect.
    Turn on car unit, put your mobile near the unit, activate your mobile bluetooth function. Soon the phone will find the new bluetooth device “CAR AUDIO” . Input the pairing password “8888” and clik OK. The phone will prompt the matching successful.
    When the pairing connect is successful, on the LCD, it shows BT ON, and the bluetooth logo will stop blinking .Then you may perform the bluetooth operation. REMARK: depend on bluetooth mobile, the bluetooth system support “HSP” “HFP” “A2DP” and AVRCP bluetooth profile.

  2. Handsfree phone service
    If your mobile phone have matched with the unit, you can dial calls out through your mobile phone. It will turn to unit automatically when calling come in and the calling phone number will indicate on the LCD screen.

    • Press the “BAND” button shortly to accept the call .Then you can talk with the other party through
      the mic on the panel.

    • Press “MUTE” button shortly to reject the call when calling come in.

    • Press “MUTE” button shortly to hang up after you finish the talk.

  3.  Advance Audio distributing profile(A2DP) playing.
    Through mobile and unit A2DP connected, press “MODE” and turn to A2DP mode at the same time, the music playing in mobile can turn to the unit audio system play. “A2DP” will display on LCD.

    • Press button “ ” and “ ” in the panel can select the music track.
    • Press “ PAUSE” button shortly to pause the music playing.
    • Press “BAND”(mode) longly to temporarily disconnect the bluetooth.
    • Press “BAND”(mode) button longly again to reconnect the bluetooth.
  4. Phone number book.
    This bluetooth system can automatically store incoming call numbers, up to 10 phone numbers.

    • Press “MUTE”(mode) button longly to enter the phone number book and press VOL button to look up the phone number.
    • Press “BAND” button once can call out you desired phone number.
  5.  Interrupt bluetooth connection/reconnection.
    Pressing the “BAND” button shortly to interrupt the bluetooth connection when your are talking a call and the voice can turn to mobile speaker.

    • Press “BAND” button again to reconnection.
      NOTE: Different mobile phone have different responses. We do not guarantee all the operation of connectable devices.
  6. How to delete stored phone number?
    The unit can store ten number of missed ,rejected and ANS separately, and the first number will auto deleted when the 11th number calling

  7. How to use “RECEIVED” “MISSED” “REJECTED” MANU ANS/AUTO ANS” Functions.
    Press MUTE for 3 seconds to enter into “RECEIVED” “MISSED” “REJECTED” MANU ANS/AUTO ANS”. Turn VOL button for choosing the telephone number.

REMOTE CONTROL LAYOUT

Kruger Matz KM0103.1 Car Radio Receiver-9

  1. PowerButton
  2. Pause / Play / Preset Button1
  3. Intro / Preset Button2
  4. Repeat Playing / Preset Button3
  5. Random / Preset Button4
  6. Preset Button5
  7. Preset Button6
  8. Mute / Hangup a call
  9. Volume Control
  10. Mode Switch
  11. Alternative Frequencies Button
  12. TrafficAnnouncement Button
  13. Scan Button
  14. Display Button
  15. APS / AMS Button
  16. Programe Type Button
  17. Band Switch / Receive a call
  18. Tuning / Selecting Tracks / F F / F R
  19. Select Button

REPLACING THE BATTERY

When the operational range of the remote control becomes short or nonfunctions while operating Replace a new CR2025 battery Make sure the battery polarity before replacement

  1. Pull out Battery Holder while pressing the stopperKruger Matz KM0103.1 Car Radio Receiver-10
  2. Put the button type battery(+)mark upward into the Battery HolderKruger Matz KM0103.1 Car Radio Receiver-11
  3. Insert the Battery Holder into the Remote controlKruger Matz KM0103.1 Car Radio Receiver-12

SPECIFICATION

General

  • Power Supply Requirements:DC 14,4V, Negative Ground
  • Load Impedance: 4 ohms
  • Maximum Output Power: 25W X 4(CH)
  • Chassis Dimensions: 178x163x50mm(WxDxH)
  • Current Drain: 10A

Tone Controls

  • Bass (at 100Hz): +10dB/-10dB
  • Treble (at 10K): +10dB/-10dB

USB/SD MUSIC Player

  • Signal to Noise Ratio: More than 60dB
  • Channel Separation: More than 60dB
  • Frequency Response: 20Hz-20KHz

FM Radio

  • Frequency Coverage (MHz): 87.5 -108MHz
  • IF: 10.7MHz
  • Sensitivity (S/N-30dB): 12dBu
  • Stereo Separation: >30dB

AM Radio

  • Frequency Coverage (KHz): 522 -1620KHz
  • IF: 450KHz
  • Sensitivity (S/N-20dB): <42dBu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals