HUMANTECHNIK A32520 Alarm Clock Lisa DS-2/RF with Lisa Radio Receiver Instruction Manual

Operation Instructions

Alarm clock lisa DS-2/RF with Lisa radio receiver

|
---|---

We would like to congratulate you on purchasing the »Lisa DS-2/RF«. You have chosen a modern and reliable system. Kindly read the instruction manual carefully in order to use the device properly and to familiarise yourself with all the possibilities of the system.

Package contents

Kindly check if all the following parts are included:

• »Lisa DS-2/RF«
• 12 volts power supply unit
• Instruction manual
• Warranty card

Should any parts be missing, kindly contact your specialist dealer or the manufacturer directly?

Functioning principle

The »Lisa DS-2/RF« is an electronic clock with a digital time display. It wakes you up with an acoustic signal which is adjustable in pitch and volume. It is also a complete list receiver, capable of displaying the signals of all Lisa transmitters. A received signal is displayed with flash and/or sound and identified by 6 indicator LEDs. The following accessories can be connected to the »AUX« connector of the alarm clock:

• Vibrating pillow
  A-3303-0

• Flash module
  A-3320-0

•  Switch module
  A-3330-0

• Acoustic module
  A-3340-0

Setup
Connect the power supply unit to the 12 V power socket of the alarm clock and plug it into a 230 V power outlet.

Setting the time
To set the time, press the time set button for one second. The hour digits will start to flash. Set the desired hour by turning the adjusting wheel (on the reverse side of the clock) to the left or right.
Press the time set button again. The minute digits will start to flash. Turn the adjusting wheel to the left or right to set the desired minutes. Pressing the time set button again will end the time setting procedure and the set time is displayed.

Setting the alarm time
To set the alarm time, press the alarm time button for one second. The hour digits of the alarm time will start to flash. Set the desired hour by turning the adjusting wheel to the left or right.

Press the alarm time button again. The minute digits of the alarm time will start to flash. Turn the adjusting wheel to the left or right to set the desired
minutes.

Pressing the alarm time button again will end the alarm time setting procedure and the set alarm time is displayed.

Alarm ON / OFF
The waking alarm can be switched on and off with the slider switch on the left side of the alarm clock.
Slider in the upper position (the green area is visible): The alarm is switched ON.
Slider in a lower position: Alarm is switched OFF.

Alarm tone ON / OFF
Press the alarm tone button for one second to switch the alarm tone ON or OFF. If the alarm tone is on, the speaker symbol will be visible in the
display.

Setting the alarm tone volume
Press and hold the alarm tone button while adjusting the volume of the alarm tone. After 2 seconds, the alarm tone can be heard. Keep the alarm tone button pressed and turn the adjusting wheel to the left or right to adjust the desired alarm tone volume. Release the alarm tone button to end the volume setting procedure.

Setting the alarm tone pitch
While adjusting the alarm tone pitch, press and hold both the alarm tone button and the spherical snooze button at the same time. After 2 seconds, the alarm tone can be heard. Keep the alarm tone button and the snooze button pressed and turn the adjusting wheel to the left or right to adjust the desired alarm tone pitch.
Release the buttons to end the pitch setting procedure.

Flash ON / OFF
Press and hold the flash button for one second to switch the flash ON or OFF. If the flash is on, the flash symbol will be visible in the display.

Setting the nighttime display brightness
The brightness of the displayed digits is automatically adjusted according to the light conditions within the room. During the day, the digits are displayed with full brightness. In the darkness, the set nighttime display brightness is activated.

To set the nighttime display brightness, press and hold the flash button . Keep the flash button pressed and turn the adjusting wheel to the left or right to adjust the desired display brightness for the night. Release the button to end the setting procedure.
If this adjustment is done during daylight conditions, the display will switch back to full brightness after a few seconds.

Snooze function

You can interrupt a current alarm by pressing the spherical snooze button. The alarm will be repeated after  5 minutes.

12 / 24-hour mode
The time can be displayed in a 12- or 24-hour mode.

The adjustment is made with the »24h/12h« switch on the reverse side of the alarm clock.

Power cut backup
The battery compartment can hold 4 batteries of size AAA (not included). In the event of a power cut, these guarantee the continuation of the set time and the display of the list signals.

Please note: During a power cut, the time display and the flash are not acting as the power consumption is too high for the backup batteries!

Lisa receiver functions:
The alarm clock is equipped with all functions of a Lisa RF receiver.

Setting the correct radio channel
A special digital transmission process ensures that the radio signals are received error-free. This process also makes it possible to set 10 different radio channels. When supplied from the factory, the »Lisa DS-2/RF« is set to channel 0. It is only necessary to set units to other channels if you have several different users operating units in the same building. Set the channel you want by adjusting the channel selector switch on the underside of the unit to the required channel number. Use a small screwdriver to adjust this switch. All transmitters and receivers within your system must be set to the same channel.

Fig. setting the correct radio channel.

Recalling the most recent signal
The »Lisa DS-2/RF« stores each signal it receives for a period of 3 minutes.

During this time, you can call up the signal again by pressing the Light/ Snooze Lisa signal cancel switch button. The signal is then displayed on the indicator LEDs. A flash signal is not triggered.

Transmission Signal Recognition
The »Lisa DS-2/RF« converts the various transmission signals into varying sequences of flash and signal displays.

Telephone:
Flashingsequence|

Telephone LED lights

---|---
Doorbell I :
Flashingsequence|

Türklingel-LED leuchtet

Doorbell II:
Flashingsequence|

Doorbell LED flashes

Baby monitor:
Flashingsequence|

Baby LED lights

Pager:
Flashingsequence|

Pager LED lights

Alarm:
Flashingsequence|

All LEDs flash

Water alarm:
Flashingsequence|

Water Alarm LED lights

Fire alarm:
Flashingsequence|

Fire Alarm LED lights

The indicator LEDs remain on for 40 seconds.

Touching the Light/Snooze switch cancels any flash alarm caused by Lisa’s signals.
The indicator LEDs light the normal time (40 seconds).

Radio range
The Lisa transmitters are designed to have a radio signal range of 80 meters under optimum conditions. The following conditions may result in a reduced range:

• Signal transmission through building structures or vegetation
•  Interference from TVs, computer monitors, and mobile phones. Under certain circumstances, this may prevent the receiver from functioning at all.
• Positioning of the transmitter at an unfavorable distance from surfaces that reflect radio waves, for example, floors and walls. This may lead to the signal wave being weakened or even canceled out by the reflected wave.
• Metallic objects reduce the range due to the shielding effect of the metal.
• Particularly in towns and cities, there may be many other sources of radio waves that can disrupt the original signal.
• Having units operating at similar frequencies located close to one another may also result in mutual inter France.

Maintenance and care
The »Lisa DS-2/RF« does not require any maintenance. If the unit does become dirty, simply wipe it clean with a soft, damp cloth. Never use spirits, thinners, or other organic solvents. Do not set up the unit where it will be exposed to full sunlight for long periods. In addition, it must be protected against excessive heat, moisture, and severe mechanical shock.

Note: This product is not protected against splash water. Do not place any containers filled with water, such as flower vases, or anything with an open flame, such as a lit candle, on or near the product.

Warranty

The »Lisa DS-2/RF« is a very reliable product. Should a malfunction occur despite the unit having been set up and operated correctly, please contact your dealer or the manufacturer directly.

This warranty covers the repair of the product and returning it to you free of charge. It is recommended that you send in the product in its original packaging, so keep the packaging for the duration of the warranty period. The warranty does not apply to damage caused by incorrect handling or attempts to repair the unit by people not authorized to do so (destruction of the seal on the unit).

Repairs will only be carried out under warranty if the completed warranty card is returned accompanied by a copy of the dealer’s invoice/till receipt.

Always specify the product number in any event.

Disposal of used electrical and electronic units (applicable in the countries of the European Union and other European countries with a separate collection system). The symbol on the product or the packaging indicates that this product is not to be handled as ordinary household waste but has to be returned to a collecting point for the recycling of electrical and electronic units. You protect the environment and health of your fellow man by the correct disposal of this product.

Environment and health are endangered by incorrect disposal. Material recycling helps to reduce the consumption of raw materials. You will receive further information on the
recycling of products from your local community, our communal disposal company, or your local dealer.

Technical data

Hereby, Sarabec Ltd declares that this device complies with all relevant UK Statutory Instruments.
The full declarations of conformity for this device are available from Sarabec Ltd., 15 High Force Road, MIDDLESBROUGH TS2 1RH. The UK.

This device complies with the following EC directives:

– 2011 / 65 / EC RoHS-directive
– 2012 / 19 / EC WEEE-directive
– 2014 / 53 / EC RED-directive

Compliance with the directives listed above is confirmed by the CE seal on the device. CE compliance declarations are available on the Internet at www.humantechnik.com.

Technical specifications are subject to change without prior notice.

Great Britain

Sarabec Ltd
15 High Force Road
GB-Middlesbrough TS2 1RH

Tel.: +44 (0) 16 42/ 24 77 89
Fax: +44 (0) 16 42/ 23 08 27
E-mail: enquiries@sarabec.co.uk

For other service-partners in Europe please contact:

Humantechnik Germany
Tel.: +49 (0) 76 21/ 9 56 89-0
Fax.: +49 (0) 76 21/ 9 56 89-70
Internet: www.humantechnik.com
e-mail: info@humantechnik.com

RM325200
2021-07

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>