INFRAMAT PRO Heating Pads

Product Information

The Inframat Pro is a far-infrared heating pad filled with
natural gemstones. It is designed by HealthyLine, a leading
innovator in gemstone heat therapy technology that enhances
wellness. The Inframat Pro uses nature-inspired medical devices
that enable you to feel good all year round. It is a heating pad
that unlocks your wellness potential, providing deep tissue and
whole-body benefits.

Contents

• Inframat Pro far-infrared heating pad
• Controller
• Warranty card

User Guide

Date: 2022-2023

Quick Start

1. Review the contents
2. Plug in the controller and warranty card
3. Plug one end of the controller into the mat
4. Plug the other end into an outlet
5. Press the Power button (see Controller Instructions on page

Product Usage Instructions

Safety Precautions

Please follow safety precautions at all times when using your
heating pad (mat).

Preheating

Preheat your mat for 15-20 minutes before use.

Temperature and Time Settings

1. We suggest starting the first few sessions with 104°F (40°C)
   for 30-minute sessions, a few times a week.

2. Gradually adjust the temperature/time settings until you find a
   comfortable level. Just pay attention to how you feel at different
   temperature settings.

3. Only sleep on a mat with low heat settings. Extended use at
   high temperatures may result in dehydration.

4. You can use your mat multiple times a day with low and medium
   settings. At high temperatures, you should not have more than one
   session per day.

5. Please allow up to 40 minutes for the surface to reach the
   highest temperature.

Hydration

Stay hydrated. If you use the mat at higher temperatures, your
body may lose water. It is important to drink plenty of water
before and after use.

Mat Cover

1. Cover the mat to protect it from moisture and stains, to
   protect your body from direct contact with hot gemstones, or to
   alleviate some heat if the surface is too hot for you. Make sure
   you cover the entire surface. Using a cover also helps gemstones to
   heat up faster.

2. A cover does not reduce the effects of FIR, negative ions, or
   PEMF.

Positioning

Lie on the mat in any way you choose. With low settings, you can
lie on the bare mat. With medium and high temperature settings, you
should cover your mat with a towel or an optional cover to protect
it from spills, sweat, or stains.

Warnings

1. Use your mat on flat surfaces. A bed, floor, or massage table
   makes for an ideal spot.

2. When using your mat in a bed or chair, we recommend placing a
   bath towel between the backside of the mat and the surface of the
   bed/chair as the backside of the mat may slightly heat up.

3. Protect your mat from moisture at all times. This includes
   spills and perspiration. You must cover your mat. You may use a
   provided cover, towel, or blanket.

4. When you cover your mat, always cover the entire surface. Do
   not partially cover your mat in any way. Partial coverage can cause
   the heat sensors to malfunction.

5. Never leave any objects on any part of the mat surface while
   the mat is heating, especially the controller. This can lead to
   uneven surface heating and possible damage to the mat or heat
   damage to the object that is placed on the mat.

INSPIRED BY NATURE PERFECTED BY SCIENCE
USER GUIDE
2022-2023

INFRAMAT PRO
far-infrared heating pads filled with natural gemstones

HealthyLine is the leading innovator in gemstone heat therapy technology that’s designed to enhance wellness. Our nature-inspired medical devices will enable you to feel good all year round.

–

CONTENT
Quick Start Guide . . . . . . . . . . . . . 4 Usage and Tips . . . . . . . . . . . . . . . 4 Warnings . . . . . . . . . . . . . . . . . . 5 Temperature Control . . . . . . . . . . . . 6 Controller Instructions . . . . . . . . . . 7 Care . . . . . . . . . . . . . . . . . . . . 11 Comfort . . . . . . . . . . . . . . . . . . 12 Notes . . . . . . . . . . . . . . . . . . . 13 Featured Therapies . . . . . . . . . . . 14 Our Policies . . . . . . . . . . . . . . . . 16 Troubleshooting . . . . . . . . . . . . . 17 Disclaimer . . . . . . . . . . . . . . . . . 17 Frequently Asked Questions . . . . . . 18

”

The Inframat Pro is not just a heating pad. It’s a key that unlocks your wellness potential. When using it, you can feel it deep in your tissue, throughout your whole body.
Michael D.

2

THANK YOU
Here at HealthyLine, we strive to achieve complete customer satisfaction by providing high-quality products that will exceed your expectations. Since 2013, we have been sharing our passion for health and wellness with the world. Our products incorporate the most effective natural materials and technologies that reach the common goal of improved health. The most important thing for us is making a difference in our customers’ lives, which is why we offer up to a 5-year limited warranty for our products.
3

QUICK START

1 2 CONTENT REVIEW

PLUG IN

Make sure you have your

Plug one end of the

controller and warranty card

controller into the mat

3 POWER UP Plug the other end into an outlet

4 POWER ON Press the Power button. Refer to the Controller Instructions (see page 7)

USAGE AND TIPS

1. Please follow Safety Precautions at all times when using your heating pad (mat).
2. Preheat your mat for 15-20 min before use.
3. We suggest starting the first few sessions with 104oF (40oC) for 30-minute sessions, a few times a week.
4. Gradually adjust the temperature/time settings until you find a comfortable level. Just pay attention to how you feel at different temperature settings.
5. Only sleep on a mat with low heat settings. Extended use at high temperatures may result in dehydration.
6. You can use your mat multiple times a day with low and medium settings. At high temperatures, you should not have more than one session per day.

7. Please allow up to 40 min for the surface to reach the highest temperature.
8. Stay hydrated. If you use the mat at higher temperatures, your body may lose water. It is important to drink plenty of water before and after use.
9. Cover the mat to protect it from moisture and stains, to protect your body from direct contact with hot gemstones, or to alleviate some heat if the surface is too hot for you. Make sure you cover the entire surface. Using a cover also helps gemstones to heat up faster.
10. A cover does not reduce the effects of FIR, negative ions, or PEMF.
11. Scan this QR code for product registration or visit healthyline.com/warranty.

Lie on the mat in any way you choose. With low settings you can lie on the bare mat.
With medium and high temperature settings you should cover your mat with a towel or an optional cover to protect it from spills, sweat, or stains
4

! WARNINGS

1. Please take the time to properly familiarize yourself with the information in this user guide before using your InfraMat Pro®. It is the owner’s responsibility that all individuals who may use the mat are aware of the correct procedures.
2. Use your mat on flat surfaces. A bed, floor, or massage table makes for an ideal spot.
3. When using your mat in a bed or chair, we recommend placing a bath towel between the backside of the mat and the surface of the bed/chair as the backside of the mat may slightly heat up.
4. Protect your mat from moisture at all times. This includes spills and perspiration. You must cover your mat. You may use a provided cover, towel, or blanket.
5. When you cover your mat, always cover the entire surface. Do not partially cover your mat in any way. Partial coverage can cause the heat sensors to malfunction.
6. Never leave any objects on any part of the mat surface while the mat is heating, especially the controller. This can lead to uneven surface heating and possible damage to the mat or heat damage to the object that is placed on the mat.
7. Do not attempt to take apart or open the mat or controller for any reason. If an issue arises, please contact us first.
8. We recommend you always use a surge protector. The wattage of the surge protector should be twice higher than that of the mat.
9. Never use pins or other metallic fasteners to hold a mat in place.
10. Do not handle the plug with wet hands.
11. Keep the controller ventilated to prevent it from overheating. Do not put the controller on soft surfaces that may cover the vents.

12. If the device overheats due to misuse, turn off the heat and place the controller on a table or other firm surface.
13. If you have any preexisting conditions that may be cause for concern, or if you have heart disease, hypertension, or any other serious medical condition you should consult with a doctor before using this or any other medical device.
14. You should avoid heat therapy if you have vascular disease, deep vein thrombosis, or multiple sclerosis.
15. Limit heat treatment at maximum temperature to one hour per day to prevent dehydration and hyperthermia.
16. Stay hydrated. It is important to drink plenty of water before and after using the mat.
17. Those who are pregnant, nursing, or have a pacemaker should not be exposed to the increased heat from the mat.
18. PEMF therapy is not suitable for those who are pregnant or individuals with a pacemaker.
19. Always unplug and power down the mat completely before folding it to put away.
20. Only fold the mat in its predetermined positions.
21. Do not immerse in water.
22. Never unplug the mat by pulling on the cord.
23. Do not use an electrical outlet that has become loose or does not engage the power plug tightly.
24. Do not remove product labels.
25. Do not use the mat with liniment, salve, or ointment preparations that contain heat-producing ingredients. Skin burns can result.
26. Do not leave your mat unattended while it is powered on, especially if children are present.

ATTENTION: Always cover your mat completely.
5

TEMPERATURE
CONTROL

Heating the gemstones in your mat naturally releases far-infrared rays and negative ions. Adjusting the strength of your exposure is as simple as adjusting the temperature of your mat. The actual temperature of a mat may vary depending on the model. The gemstones used are natural heat conductors: they get hot quickly and slowly release their heat into the air. As a general rule of thumb, the higher you set the temperature, the shorter the session should be.
95ºF – 105ºF (35-40ºC) | Overnight
Good for prolonged and overnight use. Promotes better sleep and the relaxation of both mind and body. The safe setting for those who have a sensitivity to heat.
105ºF – 130ºF (45-55ºC) | UNDER 2 HR
Good for cycles of 2 hours or less. Temporary relief of joint pain, stiffness, and minor muscle pain; provides muscular relaxation, and a temporary increase in local circulation where applied. Not too warm for the average person.
130ºF – 150ºF (55-65ºC) | 30-90 MIN
Good for 30-90 min cycles. Temporary relief of joint pain, stiffness, and minor muscle pain; provides muscular relaxation, and a temporary increase in local circulation where applied. A bit warmer than what the average person is used to. Should only be used twice a day at this setting and nothing more.
150ºF – 160ºF (65-70ºC) | 30-60 MIN
Suitable for 30-60 min cycles*. Provides a far-infrared sauna experience when the heat is trapped. Cover your body with the provided mylar blanket or with a towel to trap the heat. When you relax in intense far-infrared heat, the body works hard to release sweat, temporarily improving circulation, and recovering faster. Should only be used once a day at this setting and nothing more.

ºF
158 149 140 131 122 113 104 95 86 77

*A mat has to be covered in order to protect your body from direct contact with hot gemstones, and to protect the mat from moisture and stains (see Usage and Tips, `9)

6

ºC
70 65 60 55 50 45 40 35 30 25

CONTROLLER INSTRUCTIONS
HEAT CONTROLLER

POWER
Press the Power button to turn ON the controller. TEMP, TIMER, PEMF, and PHOTON indicators will light up on the screen.

TEMPERATURE
SET & ADJUST
Press the TEMP button once to turn ON the heat. Press TEMP again to initiate temperature adjustment mode (the temperature indicator will start flashing). Set the desired temperature and press TEMP again to save the setting.

TEMP

TEMP

TEMP

°F or °C
UNITS SET

Press & Hold for 6 sec to switch between TIME Fahrenheit & Celsius.

Scan to view video tutorial!

TIMER
SET & ADJUST
Press the TIME button to initiate time adjustment mode (the time indicator will start flashing). Set the desired time and press the TIME button again to save the setting.

TIME

TIME

FACTORY RESET
WITH THE CONTROLLER ON

Press & Hold

for 10 sec.

The controller will shut down and then turn back ON automatically.

INFORMATION
Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the Mat. Press and hold + or ­ to reach desired numbers faster. Controller instructions can be found at any time at HealthyLine.com/controllers.

7

CONTROLLER INSTRUCTIONS
HEAT + PEMF CONTROLLER

POWER
Press the Power button to turn ON the controller. TEMP, TIMER, PEMF, and PHOTON indicators will light up on the screen.
TEMPERATURE
SET & ADJUST Press the TEMP button once to turn ON the heat. Press TEMP again to initiate temperature adjustment mode (the temperature indicator will start flashing). Set the desired temperature and press TEMP again to save the setting.

TEMP

TEMP

TEMP

Scan to view video tutorial!

°F or °C
UNITS SET

Press & Hold for 6 sec to switch between Fahrenheit & Celsius.

TIME

TIMER
SET & ADJUST
Press the TIME button to initiate time adjustment mode (the time indicator will start flashing). Set the desired time and press the TIME button again to save the setting.

TIME

TIME

INFORMATION
Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the Mat. Press and hold + or ­ to reach desired numbers faster. Default PEMF frequency is set to 7.83 Hz and displayed as 8 Hz. PEMF can be turned on or off at any time with or without heat. Controller instructions can be found at any time at HealthyLine.com/controllers.
8

PEMF
SET & ADJUST
Press the PEMF button once to turn PEMF ON. Press PEMF again to initiate PEMF frequency adjustment mode (PEMF indicator will start flashing). Set the desired frequency (1-30 Hz) and press the PEMF button again to save the setting.

PEMF

PEMF

PEMF

Press & Hold for 6 sec to turn PEMF PEMF OFF.

PEMF is set as cycles of 20 min on and 100 min off, for up to 12 hr with automatic shut-off (sleep mode).

FACTORY RESET

Press

WITH THE CONTROLLER ON & Hold

for 10 sec.

The controller will shut down and then turn back ON automatically.

CONTROLLER INSTRUCTIONS
HEAT + PHOTON CONTROLLER
POWER
Press the Power button to turn ON the controller. TEMP, TIMER, PEMF, and PHOTON indicators will light up on the screen.

TEMPERATURE
SET & ADJUST
Press the TEMP button once to turn ON the heat. Press TEMP again to initiate temperature adjustment mode (the temperature indicator will start flashing). Set the desired temperature and press TEMP again to save the setting.

TEMP

TEMP

TEMP

°F or °C
UNITS SET

Press & Hold for 6 sec to switch between Fahrenheit & Celsius.

TIME

TIMER
SET & ADJUST
Press the TIME button to initiate time adjustment mode (the time indicator will start flashing). Set the desired time and press the TIME button again to save the setting.

Scan to view video tutorial!

TIME

TIME

PHOTON LIGHT
ON/OFF

to turn lights Press the PHOTON ON or OFF.

FACTORY RESET

Press

WITH THE CONTROLLER ON & Hold

for 10 sec.

The controller will shut down and then turn back ON automatically.

INFORMATION
Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the Mat.
Press and hold + or ­ to reach desired numbers faster.
Photon can be turned on or off at any time with or without heat.
Controller instructions can be found at any time at HealthyLine.com/controllers.

9

CONTROLLER INSTRUCTIONS
HEAT + PEMF + PHOTON CONTROLLER
POWER
Press the Power button to turn ON the controller. TEMP, TIMER, PEMF, and PHOTON indicators will light up on the screen.
TEMPERATURE
SET & ADJUST Press the TEMP button once to turn ON the heat. Press TEMP again to initiate temperature adjustment mode (the temperature indicator will start flashing). Set the desired temperature and press TEMP again to save the setting.

TEMP

TEMP

TEMP

Scan to view video tutorial!

°F or °C
UNITS SET

Press & Hold for 6 sec to switch between

Fahrenheit & Celsius.

TIME

TIMER
SET & ADJUST
Press the TIME button to initiate time adjustment mode (the time indicator will start flashing). Set the desired time and press the TIME button again to save the setting.

TIME

TIME

INFORMATION
Once flashing temperature has stopped, the indicator displays the actual temperature measured at the core of the Mat. Press and hold + or ­ to reach desired numbers faster. Default PEMF frequency is set to 7.83 Hz and displayed as 8 Hz. PEMF can be turned on or off at any time with or without heat. Controller instructions can be found at any time at HealthyLine.com/controllers.
10

PEMF
SET & ADJUST
Press the PEMF button once to turn PEMF ON. Press PEMF again to initiate PEMF frequency adjustment mode (PEMF indicator will start flashing). Set the desired frequency (1-30 Hz) and press the PEMF button again to save the setting.

PEMF

PEMF

PEMF

Press & Hold for 6 sec to turn PEMF PEMF OFF

PEMF is set as cycles of 20 min on and 100 min off, for up to 12 hr with automatic shut-off (sleep mode).

PHOTON LIGHT
ON/OFF

Press the

PHOTON

to turn lights ON or OFF.

FACTORY RESET

Press

WITH THE CONTROLLER ON & Hold

for 10 sec.

The controller will shut down and then turn back ON automatically.

OMFORT
Each HealthyLine mat is designed with the sole purpose of improving your health and wellness. It is a powerful wellness device. Each mat contains several pounds of real gemstones. Our Mesh models utilize large round pieces of tourmaline and jade. These mats have a hard surface. TAO, TAJ, Rainbow Chakra, SOFT, Platinum, 360-Wrap Set, as well as Portable models, utilize crushed gemstones that feel more like large pieces of sand.This is not the same as lying on a mattress as there will be varying degrees of firmness. This can be softened by covering your mat with additional layers of padding to cushion the surface.
11

ARE
1. Protect your mat from moisture at all times. Cover the entire mat with a blanket, towel, or provided cover to protect your body from direct heat and to protect the mat from sweat. You can also purchase a padded waterproof cover from HealthyLine.
2. For sanitary purposes, change and wash covers after each user. You can also use a disposable cover for each use.
3. After use, set the mat to a high temperature to allow any moisture to evaporate. After 15-20 minutes power down the controller and unplug. Do not leave your mat unattended while it is powered on.
4. Clean the surface of the mat and controller with a dry cloth as needed or use a slightly damp sanitizing wipe.
5. Do not use chemicals or solvents during cleaning. 6. If you need to store your mat, use the dustproof bag provided. 7. To fold the mat, unplug the controller, and then fold the mat inward
at predetermined places. 8. Keep the mat in a dry and ventilated place. 9. Your mat will last longer the less you fold or bend it.
12

NOTES
1. Our mats are good for people of all ages, including children. Pets can benefit from the mats, too!
2. We only sell new mats. The box you receive your package in may or may not contain our branding. The box may show signs of wear due to shipping.
3. Check our website for other products and accessories. We have special models designed for chairs, knees, arms, shoulders, and non-powered energy bedding.
4. Spread the word! Share your experience with friends, family, neighbors, social media, and groups. You may also become an affiliate or referrer.
5. For helpful videos, please visit HealthyLine.com/video.
13

FEATURES THERAPIES

Our gemstone heating pads are intended for muscular relaxation, temporary relief of stiffness, minor muscle and joint pain; for the temporary relief of joint pain associated with arthritis; for the temporary relief of muscle spasms, minor sprains, and strains; for the temporary relief of minor muscular back pain; for the temporary relief of stiffness, and increase of circulation where applied.
HOT STONES
HealthyLine uses a variety of natural gemstones to create a natural healing experience. These gemstones release far-infrared rays and negative ions when heated. They can also impact pressure points to release tension in the body. Not only can they help improve physical discomfort, but also achieve the common goal of improved health.
FAR INFRARED
Advanced heating systems and natural gemstones deliver far-infrared rays (FIR). FIR penetrates deep into the body, promoting temporary relief from stiffness, joint pain, and elevating muscle relaxation. The higher you set the temperature, the greater the level of far-infrared rays. Even organic heat from your body activates the gemstones to deliver far-infrared benefits, but at a lower level.
NEGATIVE IONS
Negative ions are found in abundance in mountains, near waterfalls, and beaches. They are also naturally emitted from gemstones. When your mat is turned on, the negative ion output significantly increases. The higher you set the temperature, the greater the level of negative ions you receive. The output of negative ions varies from 300 to 3000 per cubic centimeter, depending on the type of gemstone and temperature.
PHOTON LIGHTS
The photon lights in HealthyLine products use visible red light at a wavelength of 660 nm, that reaches just below the surface of your skin, penetrating the skin on a cellular level. For maximum benefits, photon lights should come into contact with the skin directly. Benefits are reduced when applied through a cloth or a cover. Photon light therapy may help with skin rejuvenation and improvements to your overall levels of wellness.
PEMF
Our PEMF system replicates the Earth’s electromagnetic field, which is delivered directly to your body. PEMF is the process of supplying the body with much-needed magnetic fields, bypassing the electrical pollution that affects our bodies on a daily basis. By default, PEMF is emitted at the frequency of 7.83Hz in a pulsed sinusoidal waveform — the most consistent with the biorhythms of the human body. The unique combination of revitalizing natural elements in our mats takes wellness to the next level.
14

21 UP TO LAYERS

External casing. Flexible membrane that keeps gemstones in place. Synthetic leather exterior. Durable and easy to clean.
Natural gemstones that produce far-infrared rays and negative ions. Thermal distribution layer guarantees even heat distribution.
Photon LED lights. Pulsed electromagnetic field (PEMF) system. Waterproof eleusine cloth that prevents wear.
Non-woven functional fabric for increased negative ion output. Oxford waterproof fabric to reduce damage from perspiration.
Bamboo carbon fiber cotton. Adds an additional layer of protection. Copper fabric net to shield from EMFs.
Electric discharge patented layer. Heating system. State-of-the-art silicon heating wire with EMF filtration and smart heat sensors.
Yellow mud that maximizes negative ion output. Charcoal layer. Magnetically charged layer to boost energy. Heat absorption release layer. Redistributes heat to avoid discrepancies.
Thermal insulation to prevent heat from being conducted downwards. Ecological compression cotton for comfort.
15

OUR POLICIES

WARRANTY

LIFETIME TRADE-IN

HealthyLine offers a comprehensive 1-Year Limited Warranty for all mats, and a 5-Year Limited Warranty for TAO, TAJ, Rainbow Chakra, SOFT, Mesh, Platinum, 360-Wrap Set, and any new series sold after August 1, 2020. In order to make a warranty claim, you will need to provide a purchase confirmation that verifies the purchase condition like new, purchase date, model, and serial number, as well as the price paid (see page 17). For detailed information please visit https://healthyline.com/ warranty-policy.
Scan this code for product registration or visit healthyline.com/warranty and conveniently store all the information needed to verify your claims if needed.

HealthyLine offers the world’s best lifetime trade-in policy. After the warranty period is over, regardless of your mat’s condition, you can always send it to us as a trade-in and use half of the price you paid for a new purchase. So, if something happens to your mat — it will never become a complete loss.

90-DAY FREE TRIAL
PERIOD AND PRICE
GUARANTEE
Price adjustments can be made within 90 days of your purchase if an item is further reduced in price after you purchased it. Each purchase of an Inframat Pro comes with a 90-day free trial period. You can purchase with confidence, knowing that you can return your product within that period for a full refund.

LIFETIME UPGRADE
If at any point you decide you want a larger or more advanced mat, you have the option to upgrade your current one. Please note that the new purchase must be at least twice the value of the mat you are intending to upgrade. As long as your mat is in good condition, simply send it in with assistance from our customer service team and you will get a credit of the full purchase price that will be put towards your new purchase of one or more items.

16

TROUBLESHOOTING
If for any reason your mat does not work, please be advised that this may be a minor issue that can be easily resolved. Make sure you set your mat correctly according to the instructions provided.
If there is an issue, try disconnecting the controller from the mat and the outlet; fold and unfold the mat to make sure that it lies flat so that it can function normally; turn on the controller again. Try using different sockets. Make sure you plug the controller all the way in on both ends and set the timer before trying to adjust the temperature (your mat will not heat up if the timer has not been set). Heat the covered mat at the maximum temperature for 30 minutes to check the controller is showing an increase in temperature. If you’re still having problems, please prepare the following information and then contact us:
1. Have your order number or a copy of your invoice ready. 2. Determine if your product is still within the 5 year limited
warranty period. 3. Find the model number and the serial number of your mat
on the tag of your mat. 4. Your shipping address, including zip code. 5. Once you have this information ready, contact us by email
at support@healthyline.com or call us at 1-888-774-4422
DISCLAIMER
This information is not intended to cure, diagnose, advise, or treat any medical condition, nor is reading this a substitute for reading the product User Guide. Please consult with a physician before use of this product. These statements have not been evaluated by the Food and Drug Administration. These products are not intended to diagnose, treat, cure or prevent any disease. Information with regard to our products does not reflect or represent product claims. HealthyLine assumes no responsibility for the improper use of its products or for a user’s selfdiagnosis and/or treatment using its products. HealthyLine products should not be used as a substitute for medically supervised therapy. If you suspect you suffer from clinical deficiencies, consult a licensed, qualified medical doctor. No action should be taken solely on the content provided by HealthyLine; regardless of any perceived scientific merit, readers should consult healthcare professionals on any matter related to their health. The information in HealthyLine’s materials was obtained from materials that are believed to be accurate, as presented by their respective authors, but HealthyLine assumes no liability for any errors or personal interpretation. Users and customers who fail to consult their physicians prior to the purchase or use of any product assume the risk of any adverse effects incurred. The Food and Drug Administration has not approved or evaluated the information contained in the literature here or on the website. Any printed reference or direct link to a specific product is for your information or convenience only and may not be construed as an enticement to purchase and further is not intended or implied to be used in the mitigation, diagnosis, treatment, cure, or prevention of any disease. Except as specifically stated, neither HealthyLine nor any of its directors, employees, or other representatives will be liable for damages arising out of or in connection with the use of this product or information. This is a comprehensive limitation of liability that applies to all damages of any kind, including (without limitation) compensatory, direct, indirect, or consequential damages, loss of data, income or profit, loss of or damage to property, and claims of third parties.
– All information in this booklet is subject to change without notice. – HealthyLine is not responsible for any mistakes or misprints. – Check the latest updates at HealthyLine.com.
17

FAQ

Can I use it on the floor or bed?

If I have a serious illness, can I use this mat?

Yes, our mats can be used on any flat surface such as a bed, massage table, or floor.
What size should I get to sleep on?
72″ x 24″ is recommended to sleep on. However if you roll over during the night, you might consider getting a 80″ x 30″ or 80″ x 38″ mat. Some models are also available in Queen or King sizes.
How can I burn calories?
Using our mat at high temperatures gives your body similar effects to doing cardiovascular exercise. As a reference, an hour of cardio can burn up to 500 calories. Setting the infrared heat to a temperature of 122oF-140oF (50oC- 60oC) will increase your heart rate, boost metabolism, increase your energy, and elevate blood circulation on a cellular level. You can also use the sauna effect for the calorie burner. Set the temperature to 158oF and cover your body with a regular or a mylar blanket. You will receive all the benefits of a sauna, including sweat and detoxification. At these temperatures, please keep it reasonably under one hour. And always drink plenty of water, before and after.
Is your mat protected against EMFs?
Yes, we use industry leading double insulated wiring for advanced EMF shielding. The system is then placed under EMF-filtering copper mesh layer. Mats are also made with grounding for additional EMF protection.

If you have any preexisting conditions that may be cause for concern, or if you have heart disease, hypertension, or any other serious medical condition you should consult with a doctor before using this or any other medical device.
Can I use my mat overseas?
All mats use 110V power for the USA and Canada, but you can still use the mat overseas with a good power converter. Most models are now available in 220V power — just ask or look carefully through the website.
How is 20 lbs. of gemstones so affordable?
It would cost a fortune to buy small quantities. If you were to buy 100 lbs, it costs considerably less. At HealthyLine, we buy thousands of pounds of certified gemstones each year. Because of this, we can afford to sell our mats at a fraction of its cost!
Can I wash and protect my mat?
Covering your mat fully with a towel, bed sheet, or waterproof cover will help avoid messy issues. If you must clean your mat, unplug it, and use a damp towel. If your mat is truly dirty, unplug it, and use a damp cloth with a small amount of soap. To rinse the soap, use a damp cloth and then let it air dry.

How long can I use the mat?
You can use this mat for short or extended periods — even overnight. It all depends on your preference. For extended or overnight use, settings should be at a low or comfortable setting.

18

If I have more questions what is the best way to get answers?
You can always email us at support@healthyline.com, and we’ll get right back to you, typically that same day.
What to do in case of a spill of something smelly?
1. Unplug and turn off the controller; 2. Use paper towels or dry soft cloth to absorb excess moisture
as much as possible; 3. Thoroughly wipe the affected area with multi-surface
cleaning wipes. 4. Spray odor remover on the damaged area from 6-8 inches
away. Leave the mat in a well-ventilated area until it dries completely. 5. Turn on the mat and set the maximum temperature. After the maximum is reached keep the mat running for 30-60 minutes. Do not cover the mat so that it can ventilate. Do not leave the mat unattended. 6. Repeat steps 2-5 and blow-dry the mat from a reasonable distance until it is completely dry.
I have a slight headache after using the mat. What do I do?
A headache is a sign of detoxing too fast and being dehydrated. Use a lower temperature and drink more water. Enjoy the process. Maximize your wellness at a comfortable pace.
I see your mats are made with different gemstones. Which gemstone mat should I buy?
Each mat is made with a different combination of gemstones. What you choose should depend on ailments or the area of wellness you would like to focus on. In general, the best mats come with a combination of gemstones, along with built-in PEMF.
Can I fold the mat?
Yes, you can. PEMF models are rigid and should only be folded inward at predetermined places. Please note that your mat will last longer the less you fold or bend it.
19

INFRAMAT PRO
FAR INFRARED HEATING MATS FILLED WITH NATURAL GEMSTONES

SCAN QR CODE TO SHOP
ONLINE
FAR INFRARED HEAT THERAPY MATS FILLED WITH NATURAL GEMSTONES

515 7th Avenue, New York, NY 10018

1 888 774 44 22 support@healthyline.com

@healthylinebrand @healthylineshop

References

• The Patented Pemf Mats and Original Therapy - HealthyLine™
• Warranty register - HealthyLine®
• The Patented Pemf Mats and Original Therapy - HealthyLine™

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>