FLASH F7100331 LED Par 18x15W RGBWA+UV IP65 User Manual

: June 6, 2024
: FLASH

Table of Contents

INTRODUCTION
SAFETY INFORMATION
PRODUCT INFORMATION
INSTALLATION
CONNECTION
DMX CHANNELS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

User Manual

LED PAR 18x15W

INTRODUCTION

THANK YOU FOR PURCHASING LED PAR 18x15W RGBWA+UV IP65. FOR SAFETY REASONS AND TO ENSURE A TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.

SAFETY INFORMATION

Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.
Unpack and check carefully there is no transportation damage before using the fixture.
Before operating, ensure that the voltage and frequency of the power supply match the power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Disconnect main power before servicing and maintenance.
Use a safety chain when fixing this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
Do not use the device in high humidity conditions. Use in -10°C to +35°C
In the event of a serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type of spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light spot while the fixture is on.

WARNING! The device must be connected to the power supply in order to avoid condensation.

WARNING!

IMPORTANT!
Do not point to the strong light output from other fixtures at the LED PAR, as intense illumination can damage the display.

Figure 2. Lenses can focus sunlight and strong light, presenting a risk of fire and damage to the fixture. Shield or shade the head if necessary.

PRODUCT INFORMATION

Light source: 18pcs 15W RGBWA+UV 6 in 1 LED
Power supply: AC 110V/240V 50/60Hz,
Lens Angle: 40
Signal: DMX 512
RGBW color mixing system can create innumerable colors
Housing: Extruded aluminium par housing
Waterproof: IP65
3-Pin XLR DMX input/output
Power consumption: 182 W
Net Weight: 5,2kg
Dimensions: H(24)xW(24)xD(14)[26] cm
Dim. (box): H(34)xW(29)xD(29) cm
Weight (cbox): 5,8 kg

INSTALLATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

CONNECTION

The device is equipped with the following interfaces:
1. DMX (in/out): XLR 3(5)-pin socket
2. Power (in/out): powerCON socket
5.1 Connecting DMX signal
The connection is performed using a cable with XLR-female -> XLR-Male plugs.
CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between signal (-) and signal (+) into an XLR plug and plug it in the DMX output of the last fixture.

5.2 Voltage specification

Input Voltage	Total Power	Frequency
110/240V	182W	50/60Hz

5.3 Connecting power supply
The connection is performed using a power cable with a PowerCon connector(included). The device must be operated by qualified personnel.
Make sure that the power grid supply parameters are consistent with device parameters and limitations are not exceeded.
CAUTION! In the case of cable, damage does not attempt to repair.
Replacement or repair can be made only by the manufacturer or by a person with appropriate permissions.
Using a lamp, the change rate of power voltage should be within ± 10%, if the voltage is too high, it will shorten the light’s life; if it’s not enough, the lamp will be dark. Please restart it after turning off the light for 20 minutes until full-cooling. Frequent switching will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.

5.4 LED Display function

A. Function
B. Up
C. Down
D. Enter

HOW TO OPERATE?
Press button A, there will be eight different effects.
The first two numeric stands for functions
The last two numeric stands for DMX address, or speed.
You can modify it with the B or C button.
D button is to confirm while you settled.

No.	Display	Function
1	D0001	10CHs Address Code, (001-512) Change the address code by B or C

DMX CHANNELS

Channels	Function	Details
CH.1	Dimmer	R, G, B, dimmer, linear, Dark to Bright
CH.2	Red	R dimmer, linear, Dark to Bright
CH.3	Green	G-dimmer, linear, Dark to Bright
CH.4	Blue	B-dimmer, linear, Dark to Bright
CH.5	White	W-dimmer, linear, Dark to Bright
CH.6	Yellow	Y-dimmer, linear, Dark to Bright
CH.7	Purple	P-dimmer, linear, Dark to Bright
CH.8	Strobe	Strobe from slow to fast
CH.9	Macro	0-50 dimmer mode, 51-100 jump changing program,

51-100 gradual changing program, 151-200 pulsive changing program, 201-255 sound-activated on
CH.10| Speed| Speed from slow-fast, music activated sensitivity from slow-fast

F7100331
www.flash-butrym.pl