bebird Ml3 Smart Visual Ear Cleaning Rod User Manual
- June 6, 2024
- bebird
Table of Contents
Ml3 Smart Visual Ear Cleaning Rod
User Manual
Open Ml3
-
Scan QR code to download APP
http://www.bebird.cn/app/en.html -
Ente APP Select bebird M 13
-
Open the cove Power on automatically
Connect Product WiFi
1. Connect product WiFi “bluebird-Ml3-XXXX”| 2. Back to be bird APP Click on
“Start” to use.
---|---
|
Accessory replacement
Unscrew the ear spoon head and pull out the silicone ear spoon for
replacement. Screw and plug the ear spoon head well.
The ear spoon must be assembled, in place before using it
to prevent falling off.
Accessory
1. Metal & Silicone wrapped Ear Spoon (Small ) x 1
Separate picks tor whole family| 5. Sponge Ear Spoon x 1
Removing of earwax and grease in ears
---|---
|
2. Double-colo Ear-elastic Ear Spoon (Big) Ix 1
Easy and thorough removing of cerumen| 6. Ear Pick Accessories Bucket x 1
Easily store and remove earwax
|
3. Double-color Q-elastic Ear Spoon (Small) x l
Thorough removing of cerumen| 7. Alcohol cottonswab xl
|
4. Double-color Annular Ear Spoon x 1
Easy Scraping; higher curvature| 8. Data Cable x 1
TYPE-c data cable
|
Troubleshooting
Trouble | Solution |
---|---|
Startup and no response | Please try several more times according to the |
correct boot-up method
Please use the attached charging base for charging. The charging time is about
lh
The camera does not turn on| Shut down and restart the ear cleaning rod
APP quits quickly| Delete the existing APP and re•scan the QR code for
installation.
The power indicator of the ear cleaning rod flashing rapidly in red light| Low
power mode, please charge
ear cleaning rod with the provided USB cable from the original package
WiFi connection is unstable, sometimes it is disconnected in seconds| Restart
ear cleaning rod, reconnect be bird APP
The product failed to display the real-time image after successfully
connecting the be bird APP| Disconnect the phone from WiFi, restart the
product and reconnect the WiFi
if the above operation still fails to solve the problem, please contact
Customer Service for further assistance
Hazardous Material
Part name | Hazardous Material |
---|---|
(Pb) | (Hg) |
Printed Circuit
Common ents| X| O| O| O| O| O
Case| O| O| O| O| O| O
Plastic Rubber
accessory| O| O| O| O| O| O
This form is formulated in accordance with SJ/T 11364
O: represent the hazardous material ratio is below GB/T26572-2011
X: represent the hazardous material ratio is over GB/126572-2011
Product parameter
Brand | bebird |
---|---|
肝oduct Name | bebird smart visual ear cleaning rod |
Model | Ml3 |
Rod weight | 24.3g |
Network standard | IEEE 802.llb/g/n |
Antenna | Internal FPC antenna |
Wo「king f「equency | 2.4Ghz |
Image transmission rate | 20fps |
Image sensor | CMOS |
Working temperature | 10⁓50 ° C( B21 |
Battery | 300mAh lithium battery |
Battery life | About 75 minutes |
Cha「ging time | lh |
Input parameters | 5V 0.4A |
Wo如ng voltage | 4.2V |
Rated power | 1.5W |
Lens diameter | 3.5mm |
Optimum focal length | 1.5 ⁓2cm |
Pixel | 1000W |
Gyroscope | 6 axis |
Warranty Card
User information
User information|
---|---
User name| Telephone number
Purchase date|
Seller| Telephone number
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>