OPTONICA LED Industrial High Bay Light User Manual

OPTONICA LED Industrial High Bay Light

Product Information

Specifications

• Product Name: LED Industrial High Bay Light
• Material: Aluminum Alloy
• Ring: PC Lens/Tempered glass
• IP Rating: IP65 (suitable for outdoor use)

Important Safety Information

• Do not wire this floodlight into the lighting circuit – use a switched fused spur.
• Before installation and servicing, disconnect the electrical supply at the mains.
• Carefully observe all instructions or warnings that are labelled on, or supplied with, your product.
• If in any doubt, consult a qualified electrician.

Fixing Instructions

• Do not wire this floodlight into the lighting circuit – use a switched fused spur.
• This fitting must be earthed, contact a qualified electrician to install a suitable earth facility.
• Ensure the electricity is turned off at the mains before installing or maintaining any electrical fitting.

Note
For new installations, check for any electrical cables or pipe work (gas/water) in the vicinity of the intended mounting point for this product before proceeding with the installation.

General Information
Do not mount ceiling/wall fittings onto damp surfaces such as newly painted or plastered areas as this may cause discoloration of the finish.

Tolls Required

• Drill
• Cross Head Screwdriver
• Small Electrical Slotted Screwdriver
• Insulation Tape

Product Usage Instructions

Installation
Note: Before installation, only use a round cable supplied to connect this fitting (6mm diameter minimum).

1. Install the ring with the light body. This is required in order to create a good water seal when connected to the fitting.
2. Connect the Main Line to the power wire of the lamp.
3. Ensure the terminal connection is made inside a suitable IP65 rated junction box (not included).
   • From Floodlight
   • From IP65 Rated Junction Box
4. Install the LED High bay lights on the roof or ceiling.

This product should be disposed of responsibly at the end of its life. Please recycle where facilities exist (Waste Electrical and Electronic Equipment Directive).

Importer
Prima Group 2004 LTD, Bulgaria, 1784 Sofia, Mladost 1, bl. 144, Ground Floor; Phone: +359 2 988 45 72

FAQ

• Q: Can I wire this floodlight into the lighting circuit?
  A: No, you should use a switched fused spur instead.

• Q: Is this product suitable for outdoor use?
  A: Yes, it has an IP65 rating which makes it suitable for outdoor use.

• Q: What tools do I need for installation?
  A: You will need a drill, cross head screwdriver, small electrical slotted screwdriver, and insulation tape.

USER MANUAL

LED INDUSTRIAL HIGH BAY LIGHT

Please take time to read this leaflet carefully and retain it for future reference.

DIAGRAM

IMPORTANT SAFETY INFORMATION

• Do not wire this floodlight into the lighting circuit – use a switched fused spur.
• Before installation and servicing disconnect the electrical supply at the mains.
• Carefully observe all instructions or warnings that are labeled on, or supplied with your product.
• This product is suitable for outdoor use. If in any doubt, consult a qualified electrician.

FIXING INSTRUCTIONS
Do not wire this floodlight into the lighting circuit – use a switched fused spur.
This fitting must be earthed, contact a qualified electrician to install a suitable earth facility. Ensure the electricity is turned off at the mains before installing or maintaining any electrical fitting.

NOTE
For new installations, check for any electrical cables or pipe work (gas/water) in the vicinity of the intended mounting point for this product, before proceeding with the installation.

GENERAL INFORMATION

Do not mount ceiling/wall fittings onto damp surfaces such as newly painted or plastered areas as this may cause discoloration of the finish.

Tolls which may be required

• Drill
• Cross Head Screwdriver
• Small Electrical Slotted Screwdriver
• Insulation Tape

INSTALLATION

Note: before installation.
Only use a round cable supplied to connect this fitting. (6mm Diameter minimum.)

This is required in order to create a good water seal when connected to the fitting.

1. Install the ring with the light body.
2. Connect the Main Line to the power wire of the lamp
3. Ensure the terminal connection is made inside a suitable IP65 rated junction box. (not included)
4. Install the LED High bay lights on the roof, ceiling.

This product should be disposed of responsibly at the end of its life. Please recycle where facilities exist.
(Waste Electrical ane Electronic Equipment Directive)

IMPORTER: Prima Group 2004 LTD, Bulgaria, 1784 Sofia, Mladost 1, bl. 144, Ground Floor; Phone: +359 2 988 45 72;

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>