FLYLINKtech CF900 Car Jump Starter User Manual

FLYLINKtech CF900 Car Jump Starter

Instructions

• Thank you for choosing the jump starter!
• Always follow basic safety precautions when using electrical appliances.
• Read all instructions carefully, please keep this instruction manual for easy reference.
• Model: CF900

PRODUCT LAYOUT

OPERATION GUIDANCE

LED Display

• Press the switch button to check the storage level of the jump starter.
• On the screen, it shows the remaining power and activated output ports.
• Different number displayed on the screen shows different storage level of the jump starter.
• The number will reach to 100% when the charging is completed.

Jump starter charging instruction:

1. Plug the Charging Cable to electronic devices with USB output.
2. Connect the 5V/2A input port of the jump starter to charge.

Or

1. Plug the car adaptor into the socket of the cigarette lighter.
2. Connect the 5V/2A input port of the jump starter to the other end of the car adaptor if you have one in your car.
   • Note: Don’t charge the jump starter unit immediately after starting the engines, but at least 30 minutes later.

Jumpstart 12V vehicle instruction:

1. Make sure that the remaining power is not less than what charged is suggested.
2. Plug the cord of the jumper cable into the jump start socket.
3. Connect the RED clamp to the vehicle’s battery positive (+) terminal and connect the BLACK clamp to the vehicle’s battery negative (-) terminal.
4. Start the vehicle, and the interval time between each starting must be OVER 30; if after 3 times fail, stop trying again; please check if there are problems with the vehicle engine or circuit, meanwhile, check the jump starter, if problem, please return it to the distributor.
5. When the vehicle is started, remove the jumper cable from the jump starter and disconnect the red and black clamps to the vehicle battery terminals within 30 seconds.
6. Leave the vehicle’s engine running.

Functions

1. Low voltage protection
2. Reverse polarity protection with alarm
3. Short circuit protection
4. Over-heating protection
5. Start Protection
   • Detecting: Green and Red LED flashing
   • Low voltage: Green LED off, Red LED solid
   • Ready to start: Green LED solid, Red LED off
   • Short circuit: Green LED off, Red LED solid, beeping
   • Reverse polarity: Green LED off, Red LED solid, discontinuous beeping
   • Over-heating: Green LED off, Red LED solid
   • Start Protection: Red Light solid five seconds after starting the vehicle

Instructions

1. Connect the smart cable to the jump starter unit, if the “start” and “error” indicators alternately flash with “green” and “red” lights, it proves the circuit is normal. If only the red light is on, it proves the voltage of the jump booster is too low to start the vehicle.
2. Correctly connect the smart cable to vehicles’ battery terminals; positive (+) to positive (4), negative (-) to negative (-)
3. The smart cable will detect the circuit for ‘3’, if the “start” indicator turns green, and the “error” indicator turns off, then they can start the vehicle (the green light will be on ’30’, if no start within ’30’, the smart cable will automatically shut down, and the green and red light all will be on at the same time. if want to start the vehicle again, should pull the smart cable out of the jump starter, and plug it into the jump starter again.)
4. Start the vehicle; after the vehicle starts, the “error” indicator will be red solid and beeping.
5. Immediately remove the smart cable from the vehicle battery terminals once the vehicle starts, and pull it from the jump starter unit.
6. If wrongly connect the smart cable to the vehicles’ battery terminals; positive (+) to negative (-), and negative (-) to positive (+), the circuit will be shut off immediately to protect the jump starter and vehicle; meanwhile the “error” indicator will be red solid and beeping.
7. Pull the smart cable out of the jump starter, and remove the clamps from the vehicle battery terminals, then repeat the right steps.

Charging cell phone

Charging cell phone or tablet instruction:

1. Plug the USB cable to the USB 1 or USB 2 output port.
2. Select the appropriate connector for your cell phone or pad.
3. Press the switch button to charge, the indicator will be on when the device is charging.

LED flashlight:

• Press the switch button for 3 seconds to start the LED light.
• There are 3 modes for LED light to appear in order (illumination, strobe, SOS ) if you press slightly.

PARTS LIST

TECHNICAL SPECIFICATIONS

protection
Lifetime:| >1000 cycles

FAQ

• Q. How to turn off this appliance?
• A. This appliance will power Off automatically when no load is found or charging is completed.
• Q. How many times can this appliance charge for my cell phone?
• A. 3 times for iPhone mobile phones.
• Q. How long will this appliance take to charge my mobile phone full?
• A. Approx. 1 hour.
• Q. How many times can this appliance be on a full charge to start the vehicle?
• A. Approx. 20 times.
• Q. How long will the power of the battery of this appliance remain?
• A. 3-6 months, however, we suggest to recharge it every 3 months.

WARNING

1. DO remove the from the vehicle within 30s.
2. DO NOT connect the two clamps. Otherwise, it may be dangerous!
3. DO NOT disassemble the host. Otherwise, it may be dangerous!
   • Always take care when using the appliance
   • This appliance is not intended for use by young or infirm persons without supervision.
   • Do not use it as a toy.
   • Do not allow the appliance to become wet.
   • Do not immerse the appliance in water.
   • Do not operate the appliance in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
   • Do not modify or disassemble the Jump starter. Only a suitably qualified technician may repair this unit.
   • Do not expose the appliance to heat.
   • Do not store in locations where the temperature may exceed 700C.
   • Charge only at ambient temperatures between OOC – 600C.
   • Charge only using the charger provided with the appliance.
   • Under extreme conditions, battery leakage may occur. Carefully wipe the liquid off using a cloth and avoid skin contact when you notice liquid on the batteries.
   • ln case of skin or eye contact, rinse immediately with clean water and seek medical attention.
   • At the end Of its useful life, discard the appliance with due care for our environment.

Warranty Information

1. We offer a limited warranty for this product against any defects in material and workmanship for 12 months from the date of the factory. The conditions of the warranty are as follows.
2. The warranty is only valid upon presentation of the original receipt (from the dealer/retailer) by the original purchaser with the product to be repaired or replaced.
3. The warranty is invalid if the serial number, date Of purchase, and label have been removed.
4. The warranty does not cover damage or product failure resulting from normal wear and tear, physical abuse, improper installation, modification, Or repairs by unauthorized third parties.
5. We do not assume responsibility for any loss or damage incurred during shipment or as a result of a force majeure.
6. We are not liable for any incidental or consequential damages arising from the use or misuse of the product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>