1Mii M2 Wireless Guitar System User Manual

**1Mii M2 Wireless Guitar System User Manual

**

In the Box

A. Transmitter

B. Receiver

C. Hello C. Type-C charging cable 2

D. User manual

Control Functions

2 Channel selection
Tot and pairing switch| Transmitter: Short press to switch frequency group, long press to enter pair mode.
Receiver: Long press to enter pairing mode.
5 Type-C charging port| Type-C DC5V charging.
6 3.5mm audio interface| Transmitter: Audio input Receiver: Audio output
7 Input / output signal| Transmitter: Suitable for all electric guitars and acoustic instruments
Receiver: Connect an amplifier or other sounding device.
LED indicator| Status
---|---
| LED flashes quickly| Pairing mode
LED stay Green/Blue/
Orange/Purple| Transmitter and receiver pairing successful.
Channel group display:
Green–Channel 1 , Blue–Channel 2,
Orange– Channel 3, Purple– Channel 4.
| Battery indicator| LED will be blinked during charging and be stable
for fully charged, each LED represent 25% of battery.

Installation Diagram

Usage For Guitar/Amplifier

• Transmitter shoud plug into the output jack of guitar.

• Receiver should plug into the input jack of amplifier.

Specification

Frequency Response: 5.8GHz
Frequency Broad: 20Hz-20kHz
Sampling Rate: 24bit, 48kHz
Distortion: s 0.05
Signal to Noise Ratio: 95dB
Latency: s 6.8ms
Transmission Distance: 50 meters
Charge Port: Type-C DCSV
Charge Time: 2h
Working Time: 10h
Size: 87.50>28.5 mm
Weight: 50g

Cautions
When using, do not make it face to the speaker, keep distance with guitar in order to avoid acoustic feedback even a howling problem. If a howling problem happens, try to turn down the speaker.

FQA

1. Q: The device cannot be turned on and cannot work normally.
   A: If the device is not used for a long time, or the battery is not charged in time, the battery enters the protection mode due to low power, you need to charge it and activate the battery.

2. Q: The device can be turned on, but cannot run, and there is no sound at all.
   Answer: Please check if the status indicator is always on. If the LED flashes, you need to pair the transmitter and receiver.

3. Q: Strange noise while in use.
   A: There is strong electromagnetic interference, or the transmission distance is too long, so most of the communication data is lost. Please minimize the transmission distance.

4. Q: The device cannot be charged normally.
   Answer: If the lithium battery is in a low battery state for a long time, it will enter a protection state, so you need to charge for more than 10 minutes to activate the battery.

5. Q: Can this wireless transceiver receive multiple receivers from one transmitter?
   Answer: Yes. When pairing, first put all receivers into the pairing state, and then put the transmitter into the pairing state. After pairing is complete, you can use one transmitter with multiple receivers.

FCC Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two oonditions:

1. This devioe may not cause harmful interference, and
2. this devioe must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interferenoe to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenoe to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is oonnected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

https://1mii.com/download-2/

Scan the code to get more language instructions.

Any questions? Contact:
support@1mii.com
(Response Time:4-24h,excl. holidays)

MANUFACTURER
ShenZhen 1Mii Technologies Limited.
Address: 4th FI, Bldg B, Runfeng Industrial Park, No. 4197 Baoan Blvd.,
Gushu Community, Xixiang St., Baoan Dist., Shenzhen, China.
FCC ID: 2AUFR-RT916

www.1mii.com
MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>