taurus 918692000 Sliding Care Non Stop 2500 Instruction Manual

SLIDING CARE
NON-STOP 2500

DESCRIPTION

1. Rotary ironing board
2. Pedestal
3. Extendable rod
4. Rotary nozzle // iron
5. Nozzle hanging bracket
6. Collar hanging bracket
7. Water tank| 8. Clothes protective cover
9. Clothing clip
10. Power switch
11. Steam setting switch
12. Temperature setting switch
13. Steam setting indicator
14. Temperature setting indicator
---|---

Please read this instruction booklet carefully before using the appliance and save it for future reference. Failure to follow and observe these instructions could result in an accident.

INSTRUCTIONS FOR USE

BEFORE USE:
Remove the protective film from the appliance.
Prepare the appliance according to the desired function:
ASSEMBLY

• Assembling the clothes hanging bracket

STEP1: (FIG 1)

• Unclip the movable clips on both sides of the pedestal, insert the two extendable rods. The extendable rods and the pedestal clips work in the same direction: 1) Open 2) Insert

STEP2: (FIG 2)

• After extending the extendable aluminum rods and set them to the appropriate height, lock the clips.
• Loosen 2) Extend

STEP 3: (FIG 3)

• Insert the collar hanging bracket into the top of the ironing board

STEP 4: (FIG 4)

• Unclip the movable clips on both sides of the ironing plate, then fit it on top of the extendable rods, and lock the clips
• Fitting the main body

STEP 1

• Install the flat ironing board into the rotary nozzle; (Fig 5)
• Disassemble

Assemble
STEP 2

• After extending the extendable rods and setting them to the appropriate height, lock the clip and place the rotary nozzle into the nozzle hanging bracket. (Fig 6)
• Slot into

STEP 3

• Position the main body and installation is finished. (Fig 7)

FUNCTIONAL CHARACTERISTICS (FIG 8)

• Steam setting indicator, from 1 to 3
• Heating indicator, for both dry ironing and steam ironing at temperature; 180º, 200º //Heating indicator for dry ironing only, at temperature: 80, 100, 120, 140, 160º C – Power switch + Indicator Lamp  BUTTONS. (FIG 9)
• A steam setting button from setting 1 to 3
• Temperature setting button, from setting 1 to 7

NOZZLE BUTTON

• Before use, the nozzle can be adjusted to suit ironing needs: pressing the button allows the nozzle panel to rotate 90 degrees counterclockwise. (Fig 10)
• Press down the button
• The body rotates 90 degrees counterclockwise

WARNING!

1. To avoid any risk of burns/scalding, do not adjust the nozzle angle if the temperature of the nozzle’s base plate is not at room temperature.
2. To avoid any risk of burns/scalding, do not adjust the angle if the device is still plugged in or immediately after use.

FUNCTIONAL CHARACTERISTICS

• Safety pressure relief device (Fig 11)
• Pressure relieve valve opening
• When steam pressure in the heating body becomes too high, the safety pressure relief device on the base of the main body automatically relieves pressure.
• To avoid any risk of burns/scalding, pay attention when using the high-temperature steam spray.

PRE-HEATING AND STANDBY

• 0 seconds: Power on, pre-heating time starts temperature setting 1: Approximately 15 seconds. temperature setting 7: approximately 40 seconds
• About 40 seconds: After finishing steam preheat for about 40 seconds, press the steam switch to enter into the steam ironing operation mode.
• About 1800 seconds: The machine automatically switches off after 30 minutes

OPERATION

• Filling the water tank:
•  Remove the water filler plug, pour about 1.2l water into the water tank, and refit the water filler plug, pressing tightly.
• Tip: For maximum performance and longer service life, it is best to use purified water. (Fig 12)
• Purified water
• Assemble

POWERING UP AND PRE-HEATING

1. Switch on the power supply, the main body “beeps”.

2. Press and hold the power switch on the main body for about 1 second to start the steamer, it “beeps” and the power light comes ON;

3. After connecting the power supply, the indicator flashes, as shown in the diagram, (indicating the pre-heating process),
   this remains ON constantly after finishing the pre-heating process;

4. Use the steam setting and temperature setting switch to select the desired settings based on ironing needs

FOLDING THE IRONING BOARD (Fig 13)
Ironing clothes

1. Steam ironing clothes (rotate the nozzle 90 degrees)
   – Set the temperature to 200°C or 180°C, the steam ironing function cannot be used at any other temperature settings. The steam setting can be selected by the user as required, when the temperature indicator lamp stops flashing, press the steam button switch to steam iron. While ironing, use one hand to pull the clothes taut, and the other hand to hold the steamer, iron the clothes from top to bottom, several passes of the iron may be required for heavier garments.

2. Dry ironing clothes
   – Select an appropriate temperature depending on the fabric to be ironed, place the fabric to be ironed onto the ironing board, use your hands to smooth out any initial creases, and slowly pull the clothes taut, and then iron slowly.
   – During ironing, start in a small area slowly working out to a larger area. Always iron according to different fabric and temperature instructions on the care label, or use a cloth or towel placed over the garment when necessary.

3. Ironing reference table

Note: to stop the clothing and ironing board from scorching, do not leave the nozzle in the same position for more than 30 seconds and when not in use, place the ironing head into its holder(Fig 14)
USE OF ACCESSORIES

• Use of clothing clip
• When ironing clothing that is hanging, fit the clothing clip into the collar hanging bracket, secure the clothing by moving the lips on both sides depending on the size of clothes to be ironed, and then iron the clothes. (Fig 15)
• Hook insertion slot
• Clamp the ironing board into it with the plane facing inwards

MAINTENANCE AND CLEANING

Shutdown and cooling

1.  Press and hold the power switch on the main body for 1 second, the main body “beeps” to indicate that the steamer is off, the power indicator lamp goes OFF, unplug the device and wait at least 30 minutes for the steamer to cool fully.

2. Prolonged use of tap water often results in a build-up of scale inside the steam chamber. The best way to reduce scale is to use filter water, mineral water or distilled water, it is also advisable to descale the appliance at least twice per year.

3. If it is not possible to use purified water, then scale can be reduced by doing the following steps at least once per month:
   A. Ensure the appliance is unplugged from the main supply and completely cold.
   B. Fill the water tank with a vinegar and water mixture, 1:2 proportion.
   C. Plug in the appliance and allow it to heat up, turn on the steam switch and continuously spray steam for 5 minutes, then turn off the steam switch.
   D. Empty any remaining mixture out of the water tank. Use fresh water to flush out any vinegar remaining in the tank until there is no smell of vinegar, then fill with clean water to reuse after 1 hour.

4. Remove and empty the water tank, adjust the extendable rods to accommodate storage. (Fig 17)

REMOVE

MAINTENANCE NOTES

1. Take the steam brush off the steam head and use a wet cloth to clean.
2. Do not use harsh or abrasive detergents or solvents.
3. Do not soak the steamer in water or any other liquid.
4. Do not drop it, throw it or attempt to bend it.
5. Do not attempt to dismantle the appliance.
6. Empty the water tank after each use.
7. Do not store the electric appliance in a damp/wet place.
8. Do not place the electric appliance in direct sunlight or near any heat source.
9. Always ensure that the steam outlet kept clean, free from scale and blockages.
10. The steamer should be stored vertically in a flat position.

supply and switch.
Produces little or no steam.| Check that the water tank is correctly installed. Check that the water tank has enough water.
There is scale or debris inside the water tank, clean it.
Water leaks from the tank.| Ensure that water does not exceed the highest level.
Ensure that the water tank filler hole is closed tightly.
In following the user manual, always keep the steamer in an upright position.
The steamer makes a buzzing or pumping noise when operating.| Check the water level; if there is no water or the water level is low, refill the water tank.
Metal accessories on clothes become discolored.| Do not use the steamer directly on metal accessories. Take care when using steam near any metal accessory.
The smell of scorched cloth.| Check that the temperature used matches the one on standard on the clothing care label, or use a towel;
The white powder appears when steam is sprayed.| This is not a mineral in water and it is quite normal. If it sticks to the clothing, gently shake it off.

COUNTRY Argentina
ADDRESS Av. del Libertador 1298,(B1638BEY), Vicente López (Pcia. Buenos Aires)
PHONE 541153685223

Avda. Barcelona, s/n
25790 Oliana
Spain

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>