Xing Da Electronics XO-9902 Wireless Headphone Instructions

Xing Da Electronics XO-9902 Wireless Headphone

Functions

1. Vol -/ Previous Track
2. Play/Pause/Answer/Reject
3. Vol +/ Next Track
4. LED Indicator
5. Micro USB Input
6. 3.5mm Aux Input
7. Microphone

What’s included:

• 1 x Bluetooth Headphones
• 1 x USB to Micro-USB Charging Cable 1 x Instruction Manual
• 1 x 3.5mm Aux Cable

Tech Specification

• Playing Time: 4 hours (at max volume)
• Charging Time: 2-3 hours
• Pairing Name: “Oppo Bluetooth Headphones”
• Battery: 3.7V/200mAh Li Polymer

Instructions

1. Charging the Earbuds:

   • Connect the provided USB cable to a regulated USB adapter. Connect the Micro-USB end of the cable to the charging port of the headphones(5).
   • LED indicator will turn RED when charging, once fully charged LED will turn OFF.

2. Bluetooth® Connection:

   • Press and hold Multifunction Button(2) to turn ON the headphones, headphones will and BLUE when in pairing mode.
   • Turn on the Bluetooth function on mobile device, Select “Oppo Bluetooth Headphones” pairing name.
   • Headphones will prompt and LED will slowly flash BLUE if successfully paired
   • Headphones will automatically turn
     OFF after 5 minutes if not connected to bluetooth.

3. Call Controls:

   • When receiving a phone call, press the multifunction button to answer and press again to end call.
   • Long press the multifunction button to reject a phone call.
   • Double press Vol+/Next Track(3) to activate voice Assistant/Siri.

4. Music Controls:

   • Single press Multifunction button to Play/Pause audio.
   • Short press Vol+/Next Track(3) to increase volume.
   • Long press Vol+/Next Track(3) to skip to the next track.
   • Short press Vol-/Previous Track(1) to decrease volume.
   • Long press Vol-/Previous Track(1) to skip to previous track.

5. Aux Connection:

   • Connect the provided 3.5mm Aux cable to the 3.5mm Aux Input of the headphones and mobile device to play music directly.

SAFETY PRECAUTIONS

WARNING-When using this product, basic precautions should always be followed:

• Read all the instructions before use.
• Never store or use this product in temperatures below 32°F(0°C) or above 115°F(45°C).
• The unit’s full performance is achieved only after 2 or 3 completed charge and discharge cycles.
• Do not expose the device to moisture. Do not use the device in excess of its output rating. Overload outputs above
• Do not use the device if damaged or modified
• Do not disassemble the device. For repair seek a qualified service professional. Incorrect reassembly may result in a risk of fire or injury.
• Do not expose the device to fire or excessive temperature.
• To reduce the risk of injury, close supervision is required when the product is used near children.
• Ensure that qualified service professionals use only identical replacement parts to ensure product safety

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference,
2. this device must accept any inte rference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>