Xing Da Electronics XO-10028 Wireless Earbuds User Guide

: June 6, 2024
: Xing Da Electronics

Table of Contents

Xing Da Electronics XO-10028 Wireless Earbuds
SPECIFICATIONS:
FCC Statement
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Xing Da Electronics XO-10028 Wireless Earbuds

FCC ID：2ADK3XO-10028

SPECIFICATIONS:

BT version : 5.1
Charging time : 1.5 hour(earabuds),2.5 hours (charging box)
Battery capacity Earbuds : 40 mAh
Battery capacity Charging box 400 mAh
Input of the charging box :5V/350mA Loo

Charging :

Included with your device is a Micro USB cable. Insert the Micro USB end into the Micro USB Port on the bottom of the charging case.
Insert the charging cable’s USB plug into the USB port of a computer or suitable USB charging adapter.
Case charge the earbuds: Solid Red LED on earbuds when charging, LEDs on both earbuds turn off when earbuds are fully charged.
Charge the case: Red LED flash when charging and LED turn off when case fully charged.

Bluetooth pairing:

Remove earbuds from case, prompt a voice “Power on”, then a beep to indicate both earbuds sync to each other, now main earbud LED flash Red& Blue, secondary earbud flash Blue slowly.
After connect Bluetooth, prompt a voice “connected”, now both earbuds LEDs flash blue slowly.
Touch and hold the button 1 second to enter “Transparency Mode’,touch and hold the button 1 second again to enter “ANC
ON”,touch and hold the button 1 second again to enter “ANC OFF”,
disconnect Bluetooth will prompt a voice “Disconnected”. Long press earbuds button about 5 seconds to power off earbuds and hear a voice prompt “Power off”.
If disconnect Bluetooth after 5 mins, the earbuds will auto shut off.

Earphones control:

A single touch of the Right or Left button to Play/Pause/Answer/Refuse/End a Call.
Double-touch the right multifunction button to go to the next track and double-touch the left button to go to the previous track.
Triple touch earbud button , you will hear a beeping sound to indicate that your voice Assistant/Siri is “activated” and awaiting your commands.
Put one earbud into case, the other will stay on. Put both earbuds into case, earbuds will turn off.

Note:

Keep the product dry; do not place the product in damp places.
Keep out of direct sunlight and high temperatures High temperatures may result in damage.
Keep out of cold temperatures, this will help avoid internal damage.
Do not disassemble the product.
Avoid dropping the product.
Do not continue to charge the product over 10 hours.
When charging use the Micro USB charging cord that came with the product.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modiﬁcations to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.