spigen PF2004 PowerArc ArcField Wireless Charger User Manual
- June 6, 2024
- Spigen
Table of Contents
Spigen PowerArc
ArcField™ Wireless Charger
User Manual
PC2004
Instruction
Caution
20W USB-C PD Power Adapter is Recommended for high-speed wireless charging.
USB Power Adapter is not included.
Charging Mode
The green LED light turns on when charging starts.
When the device is removed from the charger, it enters into standby mode with
an LED indicator oft
LED Indicator Display
Status|
LED
---|---
Initial power-on| 3 seconds of green. and then turn off
On-standby| The LED will turn off
While charging| Greenlight
When foreign material (metal) is detected| Greenlight blinks
Input power error (low voltage. Overvoitaeo)| Orange light blinks
When foreign material (metal) is detected:
Check to see if there is any foreign material (metal) stuck between the
smartphone and the wireless charging pad.
‘This wireless charger is not compatible with devices containing Metal Plates
or Magnets like iPhone 12 series.
Cautions
- Do not exert excess force on the product.
- Do not disassemble the product or let it come into direct contact with heat or water.
- Be careful when using the product in a hot or humid environment as it may damage the circuit.
- A magnet may cause the product to break or malfunction; do not place magnetic chip cards (eg. ID cards. credit cards) near the product
- Medical devices (e.g. pulse measuring device, hearing aid) may indirectly interfere with the product; keep them at least 20cm away from the product.
- Keep away from children. ‘ The product image herein is provided as an example and user guide for the portable high-speed wireless charger and may differ from the actual product.
*For smartphones that do not support wireless charging, you need to use a separate wireless charging patch or wireless charging case.
Note
B Class Equipment (Equipment for home use)
• This product is mainly for home use with radio wave acceptability
registration; therefore, it can be used in all areas.
Specifications
- Model : PF2004
- Input: PD 5.0Vm2.0A, 9.0V=2.0A, 12.0V=2.0A
- Output: 5.0W / 7.5W / 10.0W /15.0W
- Dimensions: 72.0 x 72.0 x 10.55mm / 2.83 x 2.83 x 0.41in
- Weight: 58g / 2.04oz
FCC Part 15 Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the product.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
ISED Regulatory Compliance
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
IC warning
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>