i Safe MOBILE M53A01 Mining+GD Smartphone User Manual

: June 6, 2024
: i safe MOBILE

Table of Contents

References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

IS530.1
SAFETY INSTRUCTIONS
MODEL M53A01

ATEX:
II 2G Ex ib IIC T4 Gb
II 2D Ex ib IIIC T135°C Db IP6X
EU Type Examination Certificate:
EPS 19 ATEX 1 037 X
CE-designation: 2004
IECEx:
Ex ib IIC T4 Gb
Ex ib IIIC T135°C Db IP6X
IECEx Certificate: IECEx EPS 19 .0014X
SANS:
Ex ib IIC T4 Gb
Ex ib IIIC T135°C Db IP6X
SANS Certificate: MTEx-S/20 .0011 X

|

North America:
Class I Div 1 Groups A, B, C, D, T4
Class II Div 1 Groups E, F, G , T135˚C
Class III Div 1
CSA19CA70220251
Temperature range:
-20°C … +60°C (EN/IEC 60079-0)
-10°C … +50°C (EN/IEC 62368-1)
Manufactured by:
i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda-Koenigshofen
Germany

---|---

EX-RELEVANT SAFETY REGULATIONS
Use of this device assumes that the operator observes the conventional safety regulations and has read and understood manual, safety instructions and certificate.
The following safety regulations must also be complied with:

Inside ex-hazardous areas the covers of all interfaces must be closed.
To ensure the IP-protection, it has to be ensured that all gaskets are present and functional. There must be no large gap between the two halves of the housing.
The device may only be charged outside ex-hazardous areas using the i.safe PROTECTOR 2.0 or i.safe PROTECTOR 3.0 USB-cable or other equipment approved by i.safe MOBILE GmbH.
When using the IS-HS1.1 headset, the headset must be securely fastened to the ISM interface.
Physical connections to equipment other than the IS-HS1.1 headset are only allowed outside ex-hazardous areas using the i.safe PROTECTOR 2.0 and i.safe PROTECTOR 3.0 USB-cable or other equipment approved by i.safe MOBILE GmbH.
The device may only be charged at ambient temperatures between +5°C . . . +35°C.
The device may not be exposed to any aggressive acids or alkalis.
The device may only be used in zones 1, 2, 21, or 22.
Only accessories approved by i.safe MOBILE GmbH may be used.

EX-RELEVANT SAFETY REGULATIONS FOR NORTH AMERICA
Conditions of Acceptability:

The battery shall only be charged outside the explosion hazardous areas only and using a suitably certified Class 2 power supply with the following output parameters: V = 5VDC I = 2000mA.
The smartphone must be protected against excessive UV light emission and high electrostatic processes.
The USB interface (type C) located at the bottom side is for data transmission and it is used in non hazardous areas. It is not permitted to open the USB interface cover in hazardous locations.
The ISM interface of the IS530.1 located at the right side can be used within hazardous areas with approved headsets, Remote Speaker Microphones(RSM) and add-ons.
For the ISM interface connection the intrinsically safe approved accessories must comply with entity parameters according to document 1029AD04
i .e . Headset IS-HS1.1 is approved to be used on ISM interface. If the ISM interface is not used, it must be securely closed by the cover provided for this purpose.

INFORMATION CONCERNING SAR CERTIFICATION (SPECIFIC ABSORBATION RATE)
Maximum SAR values for this model and the conditions under which these were determined:

SAR (head)	0 .81 W/kg
SAR (body-worn)	1 .54 W/kg

This device was tested for typical body-worn operations with the back of the handset kept 5 mm from the body . The device complies with RF specifications when the device used at 5 mm from your body .

The product shall only be connected to a USB interface of version USB2 .0.
Adapter shall be installed near the equipment and shall be easily accessible.

NB WARNING
CAUTION

Use careful with the earphone maybe possible excessive sound pressure from earphones and headphones can cause hearing loss.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
Operation temperature: -20°C …+60°C (EN/IEC 60079-0)/ -10°C …+50°C (EN/IEC 62368-1) .
The device shall only be connected via the i.safe PROTECTOR 2.0 and i.safe PROTECTOR 3.0
USB cable or another accessory authorised by i.safe MOBILE GmbH.
AC Adapter:
♦ Approved external adapter model ICP12-050-2000B (Input: AC100-240V 50/60Hz 0 .3A; Output: 5VDC, 2A) or other approved external AC/DC adapter which complies with the requirements of LPS (Limited Power Source) and has output rated 5VDC/2A .
♦ Adapter shall be installed near the equipment and shall be easily accessible .
♦ The plug is considered independent of the adapter .
The device complies with RF specifications when the device used at 0 .5 cm from your body.

The i.safe MOBILE GmbH hereby declares that this smart phone is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU . This information has to be presented in such a way that the user can readily understand it. Typically, this will necessitate translation into every local language (required by national consumer laws) of the markets where the equipment is intended to be sold. Illustrations, pictograms and using international abbreviations for country names may help reduce the need for translation.

Restrictions in the 5 GHz band:
According to Article 10 (10) of Directive 2014/53/EU, the packaging shows that this radio equipment will be subject to some restrictions when placed on the market in Belgium (BE),Bulgaria (BG), the Czech Republic (CZ),Denmark (DK), Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain(ES), France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania(LT), Luxembourg (LU), Hungary (HU), Malta (MT), Netherlands (NL), Austria(AT), Poland (PL), Portugal (PT), Romania (RO), Slovenia (SI), Slovakia (SK),Finland (FI), Sweden (SE), the United Kingdom (UK), Turkey (TR), Norway(NO), Switzerland (CH), Iceland (IS), and Liechtenstein (LI) . The WLAN function for this device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range .

| AT| BE| BG| CH| CY| CZ| DE
---|---|---|---|---|---|---|---
DK| EE| EL| ES| FI| FR| HR
HU| IE| IS| IT| LI| LT| LU
LV| MT| NL| PL| PT| RO| SE
SI| SK| TR| UK| | |

EU – Declaration of Conformity
according to directive 2014/34/EU, 2014/53/EU and 2011/65/EU (2015/863/EU)
The company i.safe MOBILE GmbH declares under its sole responsibility that the product to
which this declaration relates is in accordance with the provisions of the following data,
directives and standards:

Name & address of the manufacturer in the EU| i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda – Koenigshofen Germany
---|---
Description of the devices| Explosion protected smartphone
type: IS530.1 & IS-HS1.1
model: M53A01
Ex – marking| II 2G Ex ib IIC T4 Gb
II 2D Ex ib IIIC T135°C Db IP6X
Type examination certificate 2014/34/EU issued by
Applied harmonized standards| EPS 19 ATEX 1 037 X
Bureau Veritas E&E Product Services GmbH Businesspark A96
86842 Tuerkheim, Germany identification number: 2004
EN IEC 60079-0:2018; EN60079-11:2012
Conformity statement 2014/53/EU issued by
Applied harmonized standards| PHOENIX TESTLAB GmbH
Koenigswinkel 10
32825 Blomberg
Germany
identification number / Kenn-Nummer: 0700EN 62368-1:2014+A11:2017;
EN 50332-1:2013;
EN 50332-2:2013;
EN 50360:2017;
EN 50566:2017;
EN IEC 62311:2020;
EN 62479:2010;
EN 50663:2017;
EN 62209-1:2016;
EN 62209-2:2010+A1:2019;
|
Conformity statement 2015/863/EU amending 2011/65/EU issued by
Applied harmonized standards| SGS-CsTC Standards Technical Services Co., Ltd.
198 Kezhu Road,
Scientech Park Guangzhou Economic & Technology Development District, Guangzhou, China 510663
IEC 62321-2: 2013; IEC 62321-1: 2013;
IEC 62321-3-1: 2013; IEC 62321-5: 2013;
IEC 62321-4: 2013 + A1: 2017;
IEC 62321-7-1: 2015;
IEC 62321-7-2: 2017 & ISO 17075-1: 2017;
IEC 62321-6: 2015;
IEC 62321-8: 2017
CE Marking| 2004