fontastic Limboso Wireless Speaker User Manual

fontastic Limboso Wireless Speaker

User Manual
Thank you for choosing Limboso wireless speaker. Please read the instruction manual carefully and follow the safety instructions.

Package contents

• Bluetooth® speaker Limboso
• Micro USB charging cable
• User manual

Overview

1. Multifunction button
2. Previous title /volume –
3. Next title / volume +
4. Play/pause/station search
5. Effect LED
6. Speaker
7. On/Off switch
8. Micro USB charging port
9. Bass reflex
10. TF card slot
11. USB port

Getting started

• Charging the battery
  Limboso is equipped with an internal rechargeable lithium-ion battery. Connect the micro USB cable, which is included in the delivery, to the micro USB charging port of the Limboso (8). The USB plug of the cable can be connected to a computer or stan-dard USB power supply. The red charging LED will light up during charging. When fully charged, the red LED will turn off.

Note : Charge the speaker for at least 2.5 hours before first use.

• Switching on/off

  • To switch on the speaker, set the on/off switch (7) to „ON“.
  • To switch off the speaker, set the On/Off switch (7) to „OFF“.

• LED illumination
  Limboso is equipped with an LED illumination that starts to glow when switched on. By pressing and holding the multifunction button (1), the illumination can be switched off and on.

• Pairing with a Bluetooth® source
  The speaker must be connected to a Bluetooth® device before it can be used for wireless music streaming.

1. Switch on the loudspeaker by setting the On/Off switch (7) to „ON“. The speaker automatically switches to pairing mode.
2. Search for Bluetooth® audio devices with your Bluetooth® device from which audio data is to be played.
3. The searching Bluetooth® indicates that it has found the speaker „Limboso“.
4. Confirm the pairing with „Limboso“. Enter „0000“ if you are asked for a code.

When using a Bluetooth® device without a display, switch it to pairing mode and wait a few seconds for the connection with the speaker to be established.
NOTE: If the connection is lost or the transmitter is disconnected for a short time, turn the speaker off and on again. After switching off and on again, both devices connect automatically.

TWS function

With the TWS function you can connect two Limboso loudspea-kers together to output your music through two speakers.
To connect two Limboso, turn on both devices. Press and hold the Play/Pause button (4) on one of the devices for about 4 seconds. A signal will sound indicating that the devices are connected. Then pair one of the two speakers with the audio source as described under „Bluetooth® connection“.

Attention: When first TWS pairing the loudspeakers, the Bluetooth® function of your smartphone must be switched off
while the TWS connection is being set up. Activate the Bluetooth® function after both speakers are connected via TWS. To pair the speakers and the smartphone, follow the steps described in the „Pairing“ section.

Music playback

• Playing music via Bluetooth®
  A Bluetooth® source must be paired with Limbosoto receive and output music wirelessly! Play or pause the music playback by briefly pressing the Play/ Pause button (4).
  Note : For music streaming, the audio source must support A2DP profile.

• Music control
  To play or pause music, briefly press the Play/Pause button (4). To skip to the next title, briefly press the Next title key (3). To skip to the previous title, briefly press the Previous title key (2).
  Note: The phone must support A2DP and AVRCP profile to play and control music through the Limboso speaker.

• FM Radio
  

1. Turn on the speaker by setting the on/off switch (7) to „ON“.
2. Please connect the Micro USB cable. It serves as an antenna to receive the FM signal better.
3. Press the multifunction button (1) to switch to FM mode.
4. In radio mode, press the play/pause button (4) to search for receivable stations.
   

• Playback from Micro SD card

1. Place a Micro SD card in the card slot of the Limboso (10).
2. The device will automatically switch to SD mode and the music will be output from the speaker.

• Playback from USB

1.  Place a USB stick in the USB port (11) of the Limboso.
2.  The device will automatically switch to SD mode and the music will be output from the speaker.

• Hands-free function
  Due to the built-in microphone, the speaker is ideally suited to be used as a hands-free speaker for phone calls.
  Note: High volume may cause feedback with the microphone. This will cause echo on the phone side, not on the speaker-phone side.

• Accepting/ending/rejecting calls
  To answer an incoming call, press the Play/Pause button (4). To end an ongoing call, press the Play/Pause button (4). To reject incoming calls, press and hold the Play/Pause button (4) for approx. 2 seconds. The call is rejected.

• Adjusting the Volume
  Press and hold the volume + button (3) to increase the volume. Press and hold the volume – button (2) to decrease the volume.

Technical Data

• BT V 5.0
• Range: up to 10 m
• TWS capable
• SD card slot
• USB-A port
• FM radio
• Internal microphone
• Speaker: 3 Watts / 4Ω / Ø 4cm
• Frequency: 100Hz-20kHz
• Micro USB charging port
• Input voltage: 5V DC
• Battery: Lithium battery 1200mAh
• Music/talk time: up to 5 hrs.
• Dimensions: 11.4 x 5.2 x 10.1 cm
• Weight: 219 g

Safety information

• Never open the device.
• Do not submerge the device in water and keep it away from moisture.
• Never forcibly connect a cable.
• Place the device only on flat surfaces.
• Remove electronic devices from the power supply if they will not be used for a longer of time.
• Do not use the device if it exhibits visible damage.

No liability is accepted for any damage which may occur through improper operation.

If you require technical support, please contact our support team via email at service@fontastic.eu.

Registration and Safety

Certification/General Information

We hereby declare, that this device carries the CE mark in accordance with the regulations and standards. It conforms with the fundamental requirements of the RED 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address: www.d-parts.de/Konfo

Note on environmental protection
After the implementation of the European Directive 2012/19/EU in the national legal system, the following applies: Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details of this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilizing old devices, you are making an important contribution to protecting our environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>