ENGLAON LED32M80 32 Inch Led TV DVD Combo User Manual

LED32M80 32 Inch Led TV DVD Combo

Product Information:

Product: 32 LED TV DVD COMBO

Model: LED32M80

Important Safety Instructions:

• Immediately pull out the AC power plug if there is an abnormal
  sound or smell or if the LED TV has sound but no picture.

• Keep the LED TV free from rain, moisture, and dust to prevent
  electrical shock and short circuits.

• Do not cover the ventilation openings with table clothes,
  curtains, newspapers, etc.

• Avoid placing the LED TV near high temperature heating sources
  or direct sunlight. Maintain good ventilation by allowing at least
  10 cm of space between the LED TV and other appliances or built-in
  cabinet walls.

• When wiping the front cabinet, ensure that the power plug is
  pulled out. Use a soft, dry, lint-free cloth and handle it with
  care. Do not repeatedly wipe the panel or scrape, tap, or strike it
  with a hard object.

• Avoid using petrol, chemical, or alcohol-based solvents to
  clean the LED TV as it may damage the panel and cabinet.

• When not using the television receiver for an extended period
  of time, disconnect the AC power cord from the outlet.

• Avoid placing the LED TV on an unstable surface.

• Avoid placing the power cord or other cables across a walkway
  to prevent them from being trampled on. Do not overload the power
  cord or power socket.

• Do not disassemble the back cover as it contains high voltages.
  Only qualified professionals should conduct internal adjustments,
  maintenance, and checks.

• Avoid exposing the TV set to water droplets, vapor, or splash.
  Do not place flame sources, such as lit candles, on or near the LED
  TV. If abnormal objects or water are found in the TV, pull out the
  power plug and contact after-sales support.

• During electrical storms, pull out the power cord and antenna
  cable to protect the LED TV from damage caused by electrical
  surges. Keep all people away from the antenna cable during
  electrical storms.

Product Usage Instructions:

Assembling Stand:

1. Refer to the user manual for detailed instructions on
   assembling the stand.

Installing Batteries in the Remote Control:

1. Open the battery compartment on the back of the remote
   control.

2. Insert the batteries according to the polarity markings (+/-)
   inside the compartment.

3. Close the battery compartment.

Antenna Connection:

1. Connect the antenna cable to the RF input on the back panel of
   the LED TV.

External Connection:

Refer to the user manual for detailed instructions on connecting
external devices such as a DVD player or set-top box via different
input terminals (HDMI, USB, COAXIAL, RJ45).

Turning the TV On and Off:

1. Press the power button on the remote control or on the TV
   itself to turn it on or off.

OSD Menu Operations:

Refer to the user manual for detailed instructions on navigating
and using the On-Screen Display (OSD) menu.

DVD:

Refer to the user manual for detailed instructions on using the
DVD player functionality of the LED TV.

Troubleshooting:

Refer to the user manual for troubleshooting tips and solutions
for common issues.

Picture Defects and the Reason:

Refer to the user manual for a list of picture defects and their
possible causes.

USER’S MANUAL

32″ LED TV DVD COMBO
Model: LED32M80
User’s Manual
Please read this manual carefully and retain for future reference

Scan to download the Manual
For support please contact our service department at service@englaon.com.au

Safety Information
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacture’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two blades with one wider than the other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at the plugs, convenience receptacles, and at the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus combination to avoid injury from tip- over.
Unplug the apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. CAUTION: These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. WARNINGTo reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and that objects filled with liquids, such as vases, shall not be placed on apparatus. WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
– This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. – Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel. – The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance. Apparatus with class I construction shall be connected to a mains socket outlet with a protective earthing connection.

Important Safety Precautions
Please, immediately pull out the AC power plug from adapter if there is an abnormal sound or smell or the LED TV has sound but no picture, and contact after sales support.
The LED TV should be kept free from rain, moisture and dust to prevent electrical shock and short circuits. Do not cover the ventilation openings with table clothes, curtains, newspapers, etc.
The LED TV should be kept from high temperature heating sources or direct sunlight. Good ventilation is required. Allow 10 cm. between the LED TV and other appliances or built-in cabinet walls.
When you wipe the front cabinet, please make sure the power plug is pulled out and use a soft, dry, lint-free cloth and handle it with care. Do not repeatedly wipe the panel, nor scrape, tap or strike the panel with a hard object.
Do not wipe the LED TV with any petrol, chemical or alcohol based solvents as it will lead to product damage of the panel and cabinet.
When the television receiver is not used for an extended period of time, it is advisable to disconnect the AC power cord from the AC outlet.

Important Safety Precautions
Do not place the LED TV on an unstable surface.
Do not place the power cord or other cables across a walkway in case it is trampled on. Do not overload the power cord or power socket. When the power plug is used to disconnect and connect the device, it should easily go into the power source.
Do not disassemble the back cover, as it contains high voltages inside and will cause electric shock. Only qualified professionals should conduct internal adjustments, maintenance, and checks.
The TV set should not be subjected to water droplets, vapor, or splash. This equipment should not be placed on objects filled with liquids. Do not place flame sources, such as lit candles, on or near the LED TV. Please, pull out the power plug and contact after sales support if there are abnormal objects or water in the TV.
Pull out the power cord and antenna cable during electrical storms so the LED TV is not damaged by electrical surges. Keep all people away from the antenna cable during electrical storms.

Table of Contents
Introduction Features Accessories Specifications
General Description Overview of front and side panel Overview of back panel Assembling Stand Process Overview of remote control Installing Batteries in the Remote Control Antenna connection
External Connection Connecting DVD Player/Set-Top Box Connecting DVD Player /Set-Top Box via HDMI Connecting EARPHONE
Supporting signals
Basic operation Turning the TV On and Off
OSD Menu Operations
DVD
Troubleshooting
Picture defects and the reason

1-2 1 1 2 3-8 3 4 4 5-7 8 8
9-11 9 10 11
11
12 12
13-30
31-32
33
34

Introduction

Features

Input terminals used for external equipment connection

One AUDIO L/R output One EARPHONE output One RF input

Two HDMI input Two USB input One COAXIAL output One RJ45 input

Batteries (AAAx 2)

Instructions Manual

Remote Control 12V/24V Accessory Plug

Base

Screw

1

Introduction WSpaercniifincgastions
Model Power supply
Video input Format Antenna input Average Power Consumption

Color LED display LED32M80 1920X1080 DC 12V 5A PAL/DVB-T
48.25MHz-863.25MHz PAL/NTSC
antenna socket 75 50W
28.8 x 7.5 x 18.9 inch
4.2 Kg
0oC-35oC

Remarks: The above listed specifications and data are subject to change without prior notice.

Hardware Configuration

CPU GPU DDR SIZE eMMC Flash

ARM Cortex-A55 quad core Mali G31MP2 1.5 GB 8 GB

2

General Description
Overview of front and side panel
POWER Press POWER button to toggle between normal and standby mode. VOL+/Press to increase or decrease the volume. In the on-screen menu, use the VOL +/buttons as left/right arrow buttons. CH+/Press to change channels. In the on-screen menu, use the CH +/buttons as up/down arrow buttons. SOURCE Toggles between all the available source MENU Press to see an on-screen menu of your TV’s features.

POWER VOL+ VOL-

CH+

CH-

SOURCE MENU

3

General Description

Overview of back panel

Side port

DC 12V

RJ45

COAXIAL OUT

L

R HDMI2

HDMI1 RF

1 Port
USB1

2

3

EARPHONE OUT

USB2

4

5

67

8

9

10

1. DC 12V

6. HDMI1

DC input.

Connecting for HDMI signal.

2. RJ45

7. RF

Ethernet connection.

Connected to external antenna to receive

3. COAXIAL

the ATV/DTV program in ATV/DTV mode.

Coaxial Digital audio output.

8. USB IN

4. L/R

USB input.

Connect to the audio output jacks on your 9. EARPHONE

amplifier/home theater.

Connecting for headphone.

5. HDMI2

Connecting for HDMI signal.

Assembling Stand Process

Screw hole A Screw hole B

Screw hole C Screw hole D

Screw

Instruction: 1.Place the TV unit on a flat and clean table. 2.Fix stand by 2 pcs screws via screw hole B and A. 3.Fix stand by 2 pcs screws via screw hole D and C.

4

General Description
Overview of remote control

1

2

3

4

5

7

6

8

9

11

10

12

13

15

14

16

18

19 17

20

21

23

22

24

5

General Description
Overview of remote control
1. POWER: Turn the TV on and off. 2. : Search function. 3. Digital Buttons(0-9, -): Directly select channel with digital buttons. 4. SOURCE: Press to open the input source list. 5. NETFLIX: If network connects, press this key to view NETFLIX directly. 6. Google Play: If network connects, press this key to view Google Play directly. 7. YouTube: If network connects, press this key to view YouTube directly. 8. Prime Video: If network connects, press this key to view Prime Video directly. 9. HOME: Display the HOME page. 10. Arrow button : Use to select on-screen menu items and change menu values. 11. MENU: Display the main menu or exit the current menu. 12. OK: Confirms selection. 13. BACK: Return to the previous menu. 14. MUTE: Press this button to cut off the sound of the TV set temporarily, press again to resume. 15. EXIT: Exit the menu. 16. VOL +/- : Press these buttons to adjust the volume. 17. COLOR BUTTONS: It’s used in the APPS.
: Open/close in DVD mode. D.MENU: Quick navigation during Teletext or setup settings / DVD: Video DVD Menu button. SETUP: DVD system setup. D.DISP: Quick navigation during Teletext or setup settings / DVD: DVD Information button.
6

General Description
Overview of remote control
18. CH/: Press these buttons to change channel upward or downward. 19. GUIDE: Select electronic program guide, in DTV mode, it will display all the information of program in a week when pressing this button. 20. DIGITAL MEDIA PLAYER CONTROL BUTTON: Include backward, forward, play/pause, stop in USB mode. In DTV mode, press button to record the TV program. Please refer to relevant instructions in the section of multimedia player. 21. LIST: Press to display the channel list. A-B: Press the A-B button once to set point A. Press the A-B button a second time to set point B. After setting the program repeat playing from A to B. Pressing the AB button a third time will cancel the repeat. 22. TEXT: Press to select the teletext mode. REPEAT: DVD: Repetition mode button. 23. AUDIO: Press to select mono, nicam, stereo for ATV channel, audio language for DTV channel. 24. SUBT: Open or close subtitle. TITLE: Press this button to return to the title of the disc.
7

General Description
Installing Batteries in the Remote Control
Installing Batteries
1 Open the battery compartment cover on the back side.
Battery Cover

Insert two 1.5V AAA size batteries in
2 correct polarity. Don´t mix old or used batteries with new ones.

2xsize AAA 1.5V

Point the remote towards the remote control sensor of the wireless TV and use it within 7 meters.
Put the used batteries into the recycling bin since it can negatively affect the environment.

3 Closed the cover.
Battery Cover

The battery (battery or batteries or battery pack) shall not be exposed to excessive heat such as sunshine, fire or the like.

External Connection

Antenna connection

Antenna input impedance of this unit is 75ohm. VHF/UHF 75ohm coaxial cable can be

connected to the antenna jack directly, if the antenna cable is 300ohm parallel flat feeder

cable, you need to use the 300ohm/75ohm converter to connect the antenna cable to the

antenna jack. For details Please refer to the following drawing.

Antennas with 300ohm flat twins Leads

Antennas with 75ohm Round Leads

Use a 75ohm – 300ohm converter ANT IN

300ohm coaxial cable Antenna feeder
8

75ohm coaxial cable

Antenna cable

External Connection
Connecting DVD Player/Set-Top Box
The rear panel jacks on your TV make it easy to connect a DVD to your TV. DVD Player/Set-Top Box
Audio Cable (Not supplied)
AUDIO L OUT R
Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red) for enhanced video quality. Be sure to match the component video and audio connections. For example, if connecting the video cable to COMPONENT IN, connect the audio cable to COMPONENT IN also.
Each DVD player/STB has a different back panel configuration. When connecting a DVD player/STB, match the color of the connection terminal to the
cable. We recommend the use of cables with a Ferrite Core. 1. Connect a Component Cable between the COMPONENT IN [Y, PB, PR] jacks on
the TV and the COMPONENT [Y, PB, PR] jacks on the DVD player. 2. Connect Audio Cables between the COMPONENT IN [R-AUDIO-L] jacks on the TV
and the AUDIO OUT jacks on the DVD player.
9

External Connection

Connecting DVD Player/Set-Top Box via HDMI

This connection can only be made if there is a HDMI Output connector on the external device.

DVD Player/Set-Top Box

TV Rear Panel

HDMI Cable (Not supplied)
What is HDMI? HDMI, or high-definition multimedia interface, is a next- generation interface that enables the transmission of digital audio and video signals using a single cable without compression. Multimedia interface is a more accurate name for it especially because it allows multiple channels of digital audio (5.1 channels). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP(High Bandwidth Digital Copy Protection) coding feature installed, and supports multi-channel digital audio. Each DVD player/STB has a different back panel configuration. We recommend the use of cables with a Ferrite Core.
1. Connect an HDMI Cable between the HDMI connector on the TV and the HDMI connector on the DVD player/Set-Top Box.

External Connection
Connecting EARPHONE
EARPHONE OUT
Phone Out
1.Plug EARPHONE out connector into EARPHONE out jack on the TV the TV speaker will be muted.
Supporting signals

10

11

Basic Operation
Turning the TV On and Off
How to turn the TV on or off 1. Insert the power cord plug into a polarized DC outlet.
2. Press POWER button on the remote control or button on the LED TV. 3. Normal picture will be displayed on the screen after
6 seconds. If no signal input, “No Signal” will be displayed on the screen.
4. If temporary POWER off is required, press POWER button on the remote control or button on the LED TV.
5. If you want to completely switch off the power for this unit, unplug the power cord plug for this unit.
6. After switching off the unit, you should turn on the TV again at least 5 seconds later.
Status indication lamp Green: In power on mode. Red: In standby mode.
Auto power-off If there is no signal input in any Mode, the TV will automatically accesses the standby state in about 15 minutes.
Memory before turning TV off The settings of picture and the preset channels will be memorized at turning off the unit. When being started up again, the unit will work according to the mode set before being turned off.

OSD Menu Operations
INITIAL SETUP Press / to select the system language and press OK to confirm the language.
Connect your Android phone to your TV, select “Continue” to continue the connection, and choose “Skip” to skip this step.

12

13

OSD Menu Operations
Press / to select the wifi to connect, press OK and enter the password to confirm the connection is successful.

OSD Menu Operations

By agreeing to automatically send diagnostic information to Google to improve discriminative power, choose “YES” to accept.

Press / to select the country of your deviceand press OK to confirm.

1. Your device is powered by Android TV and press the button to select the browsing feature. 2. You can get more apps from Google Play and press the button to go to the next screen. 3. Transfer photos and other content to the TV via the built-in chromecast, press OK to complete the browsing.

14

15

OSD Menu Operations
HOME SCREEN After completing the wizard Settings, you can watch TV and go to the home screen.
1
2

OSD Menu Operations
Under live TV, press the SOURCE button to display the list of input sources. You can select the desired source.

1. Open Google Assistant or start a text search. 2. Among the applications installed on the TV, the icons for the favourite applications are shown inside here. (Favourite applications can be added/ deleted/changed its order by users.)
Inputs: Icon to select an input source. Settings: Various settings can be configured here. For details on the settings, see the next explanation.
INPUT SOURCE In the HOME interface, press /// to select the “Inputs” icon, press OK to open the input source list, then press up to highlight an input and press OK to switch.

NAVIGATING THE ON-SCREEN MENU 1. In the HOME interface, press the key to select the icon of the circular settings menu, press OK to confirm.

2. Press / button to select what you want set. 3. Press OK to enter setting.

16

17

OSD Menu Operations
Network 1 Press / button to select what you want set. 2. press OK button to adjust. 3. After finishing your adjustment, press OK button to save and return to the previous menu.

OSD Menu Operations
DEVICE PREFERENCES ABOUT

APPS

In this menu, you can read the information and settings of TV. 1. Press / button to select what you want set. 2. Press OK button to adjust. 3. After finishing your adjustment, press BACK button to return to the previous menu.

In this menu, you can set the APP permissions, and read the app lists. 1. Press / button to select what you want set. 2. Press OK button to adjust. 3. After finishing your adjustment, press BACK button to return to the previous menu.

18

19

OSD Menu Operations
DATE & TIME

OSD Menu Operations
LANGUAGE

Automatic date & time- Press / button to select the option then press OK button to enter the sub-menu.(Optional: Use network-provided time, Off)
Manually adjusting date & time settings will automaticall change the Automatic date & time to OFF.
Set date- Press / button to select the option then press OK button to enter the sub-menu. Set time- Press / button to select the option then press OK button to enter the sub-menu. Set time zone- Press / button to select the option then press OK button to enter the submenu. Use 24-hour format-Press / button to select the option then press OK button to choose ON/OFF.
20

Language- Press / button to select the optionthen press button to enter the OK select language. KEYBOARD
Current keyboard- Press / button to select the option then press OK button to enter the sub-menu. Gboard Settings- Press / button to select the option then press OK button to enter the sub-menu. Manage keyboards- Press / button to select the option then press OK button to enter the sub-menu.
21

OSD Menu Operations
STORAGE

OSD Menu Operations
GOOGLE

Internal shared storage- Press / button to select the option then press OK button to enter the sub-menu. Removable Storage- Press / button to select the option then press OK button to enter the sub-menu.(Note: Show external devices if available)
HOME SCREEN

In this menu, you can set searchable apps, safe search filter, block offensive words, open source licenses. 1. Press / button to select what you want set. 2. Press OK button to adjust. 3. After finishiing your adjustment, press BACK button return to the previous menu.
CHROMECAST BUILT-IN

In this menu, you can set channels, apps, open source licenses. 1. Press / button to select what you want set. 2. Press OK button to adjust. 3. After finishing your adjustment, press BACK button return to the previous menu.
22

In this menu, you can read the information and settings of Chromecast. 1. Press / button to select what you want set. 2. Press OK button to adjust. 3. After finishing your adjustment, press BACK button return to the previous menu.
23

OSD Menu Operations
SCREEN SAVER

OSD Menu Operations
L O C AT I O N

English

Screen saver- Press / button to select the option then press OK button to enter the sub-menu.(Optional: Turn screen off, Backdrop, Colors) When to Start- Press / button to select the option then press OK button to enter the sub-menu. (Optional: 5 minutes, 15 minutes, 30 minutes, 1 hour, 2 hours.) Start now- Press / button to select the option then press OK button to enter screen saver.
ENERGY SAVER

Location status- Press / button to select the option then press OK button to enter the sub-menu. (Optional: Use Wi-Fi to estimate location, Off)
USAGE & DIAGNOSTICS

Turn off Display- Press / button to select the option then press OK button to enter the sub-menu. (Options: 15 minutes, 30 minutes, ….24 hours, Never.) 24

Usage & diagnostics- Press / button to select the option then press button OK to choose ON/OFF.
25

OSD Menu Operations
ACCESSIBILITY

OSD Menu Operations
R E S TA R T Press OK button to enter the sub-menu. Restart the TV.

Captions- Press / button to select the option then press OK button to enter the submenu. High contrast text- Press / button to select the option then press OK button to choose ON/OFF. Text to speech- Press / button to select the option then press OK button to enter the sub-menu. Accessibility shortcut- Press / button to select the option then press OK button to choose ON/OFF. TalkBack- Press / button to select the option then press OK button to enter the submenu. Switch Access- Press / button to select the option then press OK button to enter the sub-menu.

26

27

OSD Menu Operations
ADD AND USE OF MEDIA PLAYER

OSD Menu Operations
PICTURE

1. In the HOME interface, select the + icon in the APP column to add the application, and click OK. Press up and down to select the Media Player application, and click to add it OK to the HOME interface.
2. Focus on the corresponding USB driver and press OK to display video, photo, audio files. Press navigation button to select the file.
28

Picture Mode- Press / button to select the option button to enter the submenu.(Optional: Standard, Dynamic, Movie, Eye Comfort, Gentle, Vivid, Sport, Personal). Brightness/Color Saturation/Hue/Contrast/Gamma/Black Level SharpnessPress / button to select the option. Press to decrease the parameter. Press to increase the parameter. Gamma- Press / button to select the option. Press to decrease the parameter. Press to increase the parameter. ECO Press MENU key to the main menu, and select Picture. Press button to ECO option and press OK to select the option.
29

OSD Menu Operations
SOUND
Press MENU key to the main menu, and select Sound. Sound Mode- Press OK to enter the sub-menu, press button to select option and press OK to select the option. Pure Sound- Press / button to select the option then press OK button to choose ON/OFF. Surround- Press / button to select the option then press OK button to choose O N / O F F. Sound Only- Press OK to enter the sub-menu, press OK button to select option. Output Device- Press / to enter the sub- menu. Audio Output Type- Press / to enter the sub-menu. Advanced Settings- Press / to enter the sub-menu. SYSTEM

DVD
SOURCE Press the “SOURCE” button menu, through the up and down direction keys can be select, Press the left or right button to select the DVD, and press the Enter button to enter. Press the DVD SETUP button to enter.
TV SYSTEM Set the options are: NTSC/PAL/AUTO. POWER RESUME Press the ENTER function on or off with. TV TYPE Set the screen ratio options are: PS(4:3 Pan Scan), Normal/PS(4:3 Letter Box), and Wide (16:9)the default settings is wide. PA S S W O R D Enter “0000” to enter. R AT I N G Level Disc Options. D E FA U LT This option will return the DVD to it’s factory default settings.

Press MENU key to the main menu, and select System. Press / button to select option and press OK to select the option.

30

31

DVD
OSD LANGUAGE Set the OSD Language options. AUDIO LANG DVD language selection options. SUBTITLE LANG This player can display DVD subtitle languages if supported by the DVD disc. when playing DVD’s you can hide the subtitle or choose any of them as the current subtitle language. MENU LANG Set the MENU Language options.
AUDIO OUT Press the “ENTER” Key enter, through the up and down direction keys can be select. KEY Press the “ENTER” Key enter, through the up and down direction keys can be select.
DUAL MONO Press the “ENTER” Key enter, through the up and down direction keys can be select. 32

Troubleshooting
Disconnect the power cord, wait 60 seconds then reconnect the power cord and restart the TV. C
Increase the volume. please check sound settings.
C No support for this function.
E E
E E
33

Picture defects and the reason
34

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>