fontastic SHAGI Noise Cancelling Headset User Manual

fontastic SHAGI Noise Cancelling Headset

User manual

Thank you for purchasing this Fontastic® TWS Headset ,,Shagi” with active noise cancellation. Please read the user manual carefully and follow the safety instructions.

Package content

• 2 x Shagi wireless headset
• Storage and charging case
• USB Type-C™ charging cable
• 3 pairs of ear tips
• User manual

Overview

1. Microphone
2. Multifunction sensor
3. Earpiece
4. Loudspeaker
5. Charging contacts
6. Headset slot
7. Wireless charging area (on the back)
8. Charging status indicator
9. USB Type-CTM charging port (on the bottom)

Getting Started

Charging the headsets

Insert the headsets into the charging case slots. Close the charging case. By closing the charging case, the headsets get contact and are automatically charged in the case.

Charging the case

Charge with cable:
Connect the charging cable that came with the case to the Type-CTM charging input of the case and a travel charger or USB port of a computer to charge the built-in battery. The charge status indicator flashes while charging and lights up solid when fully charged.

Wireless charging:
Place the charging case with the rear side centered on a connected wireless charging pad. The LED indicates that the case is charging.

Switching On/Off

Automatic:
Take both headset units out of the charging case, they turn on automatically. Put the headsets into the charging case and close it, the headsets turn off automatically.

Manual:
Tap and hold the multifunction sensor for 3 seconds, the headset will turn on. Tap and hold the multifunction sensor for 5 seconds, the headset will turn off.

Note: Both headsets turn on and off automatically when removed from the case or inserted.

Pairing

The Shagi headset must be paired with a Bluetooth® enabled device to be used.

1. By removing both headset units from the charging case, they will automatically turn on, sync with each other, and enter pairing mode to connect to a Bluetooth® source.
2. Search for ,,Shagi” on your Bluetooth® enabled device and select it from the list of found devices to pair the headset with the Bluetooth device.

Note: When the headset is placed in the charging case, the connection is interrupted. As soon as both headsets are removed, they will automatically reconnect. If the headset units do not connect automatically or an existing connection is disconnected, switch both headsets off and on again either by inserting and removing them from the charging case, or manually.

Note: If the headset does not find a Bluetooth®-enabled device, it switches off after approx. 3 minutes.

Music Control

All control commands are executed with the multifunction sensor.

Play/Pause: Tap the multifunction sensor on one of the two heasdsets once.
Skip Backwards: Tap the multifunction sensor of the left head 2 times.
Skip Forwards: Tap the multifunction sensor of the right headset 2 times.

Hands-free functions

Answer/hang up/reject call:
Answer incoming call: Tap the multifunction sensor on either headset unit once.
End ongoing call: Tap the multifunction sensor on either headset unit once.
Reject incoming call: Tap the multifunction sensor on either headset unit twice.

Modes

Shagi features active ambient noise cancellation (ANC) so that ambient noise is not distracting when streaming music or making phone calls.

Transparent Mode: Tap and hold the multifunction sensor on the right headset for 2 seconds to activate Transparent Mode. When activating the transparent mode, ,,Transparency” sounds, here the ambient noise is transported directly into the loudspeakers of the headsets. Thus, the ambient noise can be perceived better.

ANC mode: Tap and hold the multifunction sensor on the right headset again for 2 seconds to activate active noise cancellation. When activating ANC mode, a high pitched tone will sound, by activating ANC mode, some ambient noise will be suppressed.

Normal mode: Tap and hold the multifunction sensor on the right headset for 2 seconds again to switch back to Normal mode. When activating Normal mode (ANC Off), a slightly deeper sound is heard.

Gaming Mode: Tap and hold the multifunction sensor on the left headset for 2 seconds to activate Gaming Mode. This lowers the latency so that the transmission is less than 60 ms and gaming or TV is possible without audible delay.

Voice assistant

Tap the multifunction sensor on either headset unit three times to activate the voice assistant.

Adjusting the volume

The volume is adjusted via the Bluetooth source.

Note: In rare cases, the super bass of the headset may be overdriven by the settings of the mobile phone. In this case, use the ,,Normalise” function (also ,,Adjust volume”) in the audio settings of your phone.

Safety advice:

• Do not use the headset at high volume for prolonged periods of time.
• Be careful not to use headset in potentially dangerous situations.
• Do not use the headset while operating a vehicle.
• Never open the device.
• Never immerse the device in water, always protect it from moisture.
• Disconnect electronic devices from the power when not using them for longer time.
• Do not use headphones if they show any visible damage.

Technical data:

Headsets

• BT version 5.1
• Profiles: Headset, Handsfree, A2DP, AVRCP
• Range: up to 10 m
• Driver: 13 mm
• Frequency: 20hz-20Khz
• Impedance: 32 ± 15%
• AAC audio decoding
• Active noise cancelling
• Built-in high performance microphone
• Status LED
• Battery: 40 mAh
• Operating time: up to 6 hrs
• Dimension per unit: 36 x 26 x 22 mm
• Weight per unit: 4.5 g

Charging case:

• Built-in battery for charging the headsets
• USB Type-CTM charging port
• Battery: 320 mAh
• Dimensions: 61 x 26 x 48 mm

The company is not responsible for any damage due to improper operation.

If you need technical support, please contact our support team by e-mail at service@fontastic.eu.

We hereby declare, that this device carries the CE mark in accordance with the regulations and standards. It conforms with the fundamental requirements of the (RED) 2014/53/EU directive.
The full text of the EU Declaration of Conformity is available at the following Internet address www.d-parts.de/Konfo

Note on environmental protection:

After the implementation of the European Directive 2012/19/EU in the national legal system, the following applies: Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details of this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, re-using the materials or other forms of utilising old devices, you are making an important contribution to protecting our environment.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks is under license.
USB Type-CTM and USB-CTM are trademarks of USB Implementers Forum.
Improvement and changes of the technical specifications and other data’s could be made without prior notice.
Registered trademarks are the property of their respective owners.

Fontastic, by D-Parts GmbH Birkenweiher Str. 16 63505 Langenselbold, Germany
www.d-parts.de

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>