fontastic MACARO Full Wireless Stereo Headset User Manual
- June 6, 2024
- fontastic
Table of Contents
fontastic MACARO Full Wireless Stereo Headset
User Manual
Thank you for choosing this Macaro wireless headset. Please read this user
manual carefully and comply with the safety instructions.
Package Contents
- 2 x wireless headset Macaro
- Storage and charging case
- USB Type-C™ cable
- 3 pairs of earbuds
- User manual
Overview
- Status LED
- Multimultifunction sensor
- Earbuds
- Speaker
- Charging contacts
- Microphone
- Cover
- Headset insertion
- Charging Pins
- USB Type-C™ charging port
- Charging LED case
Getting Started
Charging the headset
Insert the headset into the charging case. The headsets are automatically
charged in the case. The LEDs (1) of the headsets light up red during the
charging process, the LED of the case (11) is lights up green. After complete
charging, all LEDs will turn off.
Charging the case
Connect the USB Type-C™ cable, included with the headset, to the charging case
and to a power supply or USB port on a computer to charge the battery of the
case. The LED of the case (11) flashes red during charging and lights up
permanently when fully charged.
Switching On/Off
- Switch on: Tap and hold the multifunction sensor (2) for about 2-3 seconds.
- Switch off: Tap and hold the multifunction sensor (2) for about 5-6 seconds.
Note: Both headsets switch on and off automatically when they are removed or
inserted from the case.
When the headsets are switched on, the LED`s (1) flash red and blue until both
headsets are connected. After pairing, the LED on one headset will turn off
and the LED on the other headset will flash red and blue alternately. This
indicates that the headset is ready to pair with a Bluetooth® enabled device.
Pairing
The Macaro Headset has to be paired with a Bluetooth® device before use. The LED (1) of one of the headsets flashes blue and red while it is ready to pair.
- Turn on both headsets, they will be connected automatically via TWS. Now one headset starts pairing mode to connect with Bluetooth® enabled device.
- Search for “Macaro” on your Bluetooth® device and select it to pair the headset with your device. The LED of both headset will turn off after a successful pairing.
NOTE: When pairing for the first time, it is recommended to switch the
„Macaro“ TWS off and on manually before connecting it.
Activate the Bluetooth connection from the device only after turning it on.
Note: If the Headste does not find a Bluetooth® capable device, it
switches itself off after approx. 3 minutes.
Note:
- When the headset is placed in the charging case, the connection is interrupted. As soon as the headset is removed, the headset automatically reconnects.
- If the connection is interrupted, the multifunction sensor must be pressed to reconnect.
Note for Headset Use
All control commands are executed with the multifunction sensor (2). The
headsets can be worn on the left or right side, therefore the direction for
control may vary.
Music Control
- Play/Pause: Tap the multifunction sensor on one of the two heasdsets once.
- Skip Backwards: Tap the multifunction sensor of the right head 3 times.
- Skip Forwards: Tap the multifunction sensor of the left headset 3 times.
Hands-free control
- Answer/Hang up Call: Tap the multifunction sensor (2) once.
- Reject call: tap and hold the multifunction sensor (2) for one second when the call comes in.
- Voice dial /Voice Command: When in standby, tap and hold the multifunction sensor for 2 seconds. The voice Command is activated.
Volume setting
- To increase the volume, tap the multifunction sensor (2) on the right-hand headset 2 times.
- To decrease the volume, tap the multifunction sensor (2) on the left-hand headset 2 times. Refer to : „Note for Headset Use“.
Note: Rarely does it happen that the headset‘s superbass is clipping by mobile phone settings. In this case, use the „Normalise“ function (also known as „Adjust volume“) in the audio settings of your phone.
Safety advice
- Do not use the headset at high volume for prolonged periods of time.
- Be careful not to use headset in potentially dangerous situations.
- Do not use the headset while operating a vehicle.
- Never open the device.
- Never immerse the device in water, always protect it from moisture.
- Disconnect electronic devices from the power when not using them for longer time.
- Do not use headphones if they show any visible damage
Technical Specifications
Headsets
- BT version 5.0
- Profiles: Headset, Handsfree, A2DP, AVRCP
- Range: up to 10 m
- Driver: 8 mm
- Frequency: 20Hz-20KHz
- Sensitivity: 96 ± 3dB
- Built-in microphone
- Status LED
- Battery: 30 mAh
- Operating time: up to 3 hours
- Weight per unit: 3g
Charging case
- Built-in battery for headset charging
- Battery: 250 mAh
- Status LED
- USB Type-C charging port
- Dimensions: 44 x 44 x 28 mm
The company is not responsible for any damage due to improper operation.
If you need technical support, please contact our support team by e-mail at
[email protected].
We hereby declare, that this device carries the CE mark in accordance with the
regulations and standards. It conforms with the fundamental requirements of
the (RED) 2014/53/EU directive.
The full text of the EU Declaration of Conformity is available at the
following Internet address
www.d-parts.de/Konfo
Note on environmental protection
After the implementation of the European Directive 2012/19/EU in the national
legal system, the following applies: Electrical and electronic devices may not
be disposed of with domestic waste. Consumers are obliged by law to return
electrical and electronic devices at the end of their service lives to the
public collecting points set up for this purpose or point of sale. Details of
this are defined by the national law of the respective country. This symbol on
the product, the instruction manual or the package indicates that a product is
subject to these regulations.
By recycling, re-using the materials or other forms of utilising old devices,
you are making an important contribution to protecting our environment.