i Safe MOBILE M655A01 IS655.2 Smartphone User Manual

: June 6, 2024
: i safe MOBILE

QUICK START MANUAL
SAFETY INSTRUCTIONS
IS655.2
MODEL M655A01

KEYS AND SPECIAL FEATURES

INTRODUCTION

This document contains information and safety regulations that are to be observed without fail for the safe operation of the device IS655.2 (Model M655A01) under the described conditions. Non-observance of this information and instructions can have serious consequences and/or may violate regulations. Please read the manual and these safety instructions before using the device. In case of any doubt, the German version shall apply. The current EU declaration of conformity, certificate of conformity, safety instructions, and manuals can be found at www.isafe-mobile.com, or requested from i.safe MOBILE GmbH.

RESERVATION

The content of this document is presented as it currently exists. i.safe MOBILE GmbH does not provide any explicit or tacit guarantee for the accuracy or completeness of the content of this document, including, but not restricted to, the tacit guarantee of market suitability or fitness for a specific purpose unless applicable laws or court decisions make liability man- datory. i.safe MOBILE GmbH reserves the right to make changes to this document or to withdraw it any time without prior notice. Changes, errors, and misprints may not be used as a basis for any claim for damages. All rights reserved.
i.safe MOBILE GmbH cannot be held responsible for any data or other loss and direct or indirect damages caused by any improper use of this device.

EX-SPECIFICATIONS

The device IS655.2 is suitable for use in potentially explosive atmospheres classified as zone 2/22 in accordance with directives 2014/34/EU, as well as the IECEx scheme.

EX-MARKINGS

ATEX:
II 3G Ex ic IIC T4 Gc IP54
II 3D Ex ic IIIB T135°C Dc IP54
Certificate of conformity:
EPS 19 ATEX 1 129 X
CE-designation:
IECEx:
Ex ic IIC T4 Gc IP54
Ex ic IIIB T135°C Dc IP54
IECEx Certificate: IECEx EPS 19.0064X
North America:
Class I Div 2 Groups A, B, C, D, T4
Class II Div 2 Groups F, G , T135˚C
Temperature range:
-10°C … +60°C (EN/IEC 60079-0)
-10°C … +55°C (EN/IEC 62368-1)
Manufactured by:
i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda-Koenigshofen
Germany
EU-DECLARATION OF CONFORMITY
The EU declaration of conformity can be found at the end of this manual.
FCC/IC STATEMENT
The FCC/IC Statement can be found under downloads on the product page of our website: www.isafe-mobile.com/en/products.

FAULTS AND DAMAGES

If there is any reason to suspect that the safety of the device has been compromised, it must be withdrawn from use and removed from any ex-hazardous areas immediately. Measures must be taken to prevent any accidental restarting of the device. The safety of the device may be compromised, if, for example:

Malfunctions occur.
The housing of the device shows damage.
The device has been subjected to excessive loads.
The device has been stored improperly.
Markings or labels on the device are illegible.

We recommend that a device displaying errors or in which an error is suspected be sent back to i.safe MOBILE GmbH to be checked.

EX-RELEVANT SAFETY REGULATIONS

The use of this device assumes that the operator observes the conventional safety regulations and
has read and understood the manual, safety instructions, and certificate.
The following safety regulations must also be complied with:

Inside ex-hazardous areas, the covers of all interfaces must be closed.
To ensure the IP-protection, it has to be ensured that all gaskets are present and functional.
There must be no large gap between the two halves of the housing.
The device may only be charged outside ex-hazardous areas.
The device may only be charged at ambient temperatures between 5°C … 35°C.
Physical connections to other equipment are only allowed outside ex-hazardous areas.
The device may not be exposed to any aggressive acids or alkalis.
Only accessories approved by i.safe MOBILE GmbH may be used.
The device may only be used in zones 2 or 22.

EX-RELEVANT SAFETY REGULATIONS FOR NORTH AMERICA

Conditions of Acceptability:

The headset connector and the USB micro connector are to be used in non-hazardous areas only.
The battery may be charged outside explosion hazardous areas only using approved external adapter model ICP12-050-2000B with output rated 5Vdc, 2A, or other external approved AC/
DC adapter for use in the US and Canada which also complies with the requirements of LPS and has output rated 5Vdc, 2A.
The battery pack is placed permanently into the housing therefore do not detach the two halves of the enclosure. It is not user-serviceable or interchangeable.
In order to maintain the IP64 protection, do not detach the two halves of the enclosure.
The device must be protected from impacts with high impact energy, against excessive UV light emission and high electrostatic charge processes.

FURTHER SAFETY ADVISES

Do not touch the screen of the device with sharp objects. Dust particles and nails may scratch the screen. Please maintain the screen clean. Remove dust on the screen with a soft cloth gently, and do not scratch the screen.
Charge the device under indoor conditions only.
Do not put the device in environments with excessive temperatures, as this could lead to
heating of the battery, resulting in fire or explosion.
Do not charge the device near any flammable or explosive substances.
Do not charge the device in environments with much dust, humidity, or excessively high or low temperatures.
Do not use the device in areas where regulations or legislation prohibit the use.
Do not expose the device or charger to strong magnetic fields, such as are emitted from induction ovens or microwaves.
Do not attempt to open or repair the device. Improper repair or opening can lead to the destruction of the device, fire, or explosion. Only authorized personnel are allowed to repair the device.
Power off the device in hospitals or other places where the use of mobile phones is prohibited.
This device may affect the proper work of medical equipment, such as pacemakers. Always keep a distance of at least 15 cm between the device and these devices.
To prevent possible hearing damages, do not listen at a high volume level for long periods. Fully understand user manual before use. Ensure your player is at low volume
levels or power off before you leave.
Observe all corresponding laws that are in force in the respective countries regarding the use of devices while operating a vehicle.
Please power off the device and disconnect the charging cable before cleaning the device.
Do not use any chemical cleaning agents to clean the device or the charger. Use a damp and anti-static soft cloth for cleaning.
Do not discard old and abandoned lithium batteries into the trash, send them to designated waste disposal locations.
The user alone is responsible for any and all damages and liabilities caused by malware downloaded when using the network or other data-exchange functions of the device.
i.safe MOBILE GmbH cannot be held responsible for any of those claims.

MAINTENANCE/REPAIR

Please note any legal requirements for periodic inspection.
The device itself has no user-serviceable parts. It is recommended to perform inspections according to the safety regulations and advice. If there is a problem with the device, please contact your vendor or consult the service center. If your device is in need of repair, you can either contact the service center or your vendor.

BATTERY

The battery is fixed installed and not user-serviceable.
The battery is not fully charged when the device is purchased, but it contains enough energy
to power on the device. To obtain the best battery performance and battery life, let the battery discharge completely before charging it completely for the first three charging cycles.

CHARGING THE BATTERY
Connect the USB cable with the USB port (5).
Then connect the cable with a power adapter.
After charging, remove the USB cable from the charger. 1.5m drop r IP68 water and dust resistant

WARNING
The device battery may only be charged within a temperature range of 5°C to 35°C! Never charge the battery outside this temperature range.

BATTERY USE
In actual use, the run time of the device varies with the network status, working environment, and usage.
When the power of the battery is lower than normal, the device will prompt you to charge it.
Please charge the battery; otherwise, you may lose any files which are not saved. If you do not charge for a long time, the device will be powered off automatically.
INSTALLATION OF THE NANO SIM CARD
The SIM card tray features the usage of 2 SIM cards or 1 SIM card in combination with 1 microSD card. This is located under the upper left cover (2) (see page 2). SIM/Micro SD

WARNING
Do only change the SIM card when the device is switched off. Do not try to insert or remove the SIM card when any external power supply is connected, otherwise, the SIM card may be damaged.

INSTALLATION OF THE microSD CARD
The device features a microSD card slot (up to 128 GB). This is located under the upper left cover
(2) (see page 2).
If you want to remove the microSD card, please make sure that the card is not in use by the
device. To remove the microSD card follow the instructions given in → → → .
WARNING
Do only change the micro SD card when the device is switched off. Do not try to insert or remove the micro SD card when any external power supply is connected, otherwise, the micro SD card may be damaged.

POWERING ON THE DEVICE
Press the [On/Off Key] until the screen lights up. Depending on the security settings of your SIM card, the device may ask you for your personal identification number (PIN) before starting up.
The first time you power on your device, you may be prompted to assign a language, date, and time zone and enter your personal information. You will also be asked to sign in or set up your Google Account. You can do this later but please note that some of the functions of the device like Google Play depend on a Google Account.

KEYS AND SPECIAL FEATURES

(see illustration on page 2)

EARPHONE JACK : To connect an earphone.
SIM CARD TRAY : To insert SIM card and microSD card.
SIDE KEY LEFT : Optional key used by different apps.
BACK KEY : Back to the previous screen mask.
USB-PORT : For charging the phone and connecting to other devices with the delivered USB cable.
HOME KEY : To go back to the home screen.
CURRENT APPLICATION : This shows all open applications.
POWER KEY : Long press to power ON/OFF the device. Short press to power ON/OFF the standby mode.
LOUDNESS CONTROL : Volume up/Volume down

RECYCLING

The crossed-out wheeled bin symbol on your product, battery, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies to the European Union. Do not dispose of these products as unsorted municipal waste. Always return your used electronic products, batteries, and packaging materials to dedicated collection points. This way you help prevent uncontrolled waste disposal and promote the recycling of materials. More detailed information is available from the product retailer, local waste authorities, national producer responsibility organizations, or your local i.safe MOBILE GmbH representative.

INFORMATION CONCERNING SAR CERTIFICATION

(SPECIFIC ABSORBATION RATE)

Maximum SAR values for this model and the conditions under which these were determined:

SAR (body-worn)	1.86 W/kg
SAR (head)	0.59 W/kg

This device was designed for typical body-worn activities and tested based on the European standards EN 62209-1:2016 and EN 62209-2:2010.

TRADEMARKS

i.safe MOBILE and the i.safe MOBILE logo are registered trademarks of the i.safe MOBILE GmbH.
EEA version: Comes with the Google app and Google Chrome™ Google and Google Play are trademarks of Google LLC.
All other trademarks and copyrights are the properties of their respective owners.

CONTACT/SERVICE CENTER

FOR FURTHER QUESTIONS PLEASE CONTACT OUR SERVICE CENTER:
i.safe MOBILE GmbH
i_Park Tauberfranken 10
97922 Lauda-Koenigshofen
Germany
service@isafe-mobile.com
www.isafe-mobile.com/service

MAXIMUM OUTPUT POWER

Frequency bands	Maximum output power
GSM 900	34dBm
DCS 1800	32dBm
WCDMA 900	25dBm
WCDMA 2100	25dBm
LTE Band 1	25dBm
LTE Band 3	25dBm
LTE Band 7	25dBm
LTE Band 8	25dBm
LTE Band 20	25dBm
LTE Band 28	25dBm
LTE Band 38	25dBm
LTE Band 40	25dBm
WiFi	20dBm
WiFi 2.4G	20dBm
WiFi 5G	15dBm
BT	15dBm

Restrictions in the 5 GHz band:

According to Article 10 (10) of Directive 2014/53/EU, the packaging shows that this radio equipment will be subject to some restrictions when placed on the market in Belgium (BE),- Bulgaria (BG), the Czech Republic (CZ), Denmark (DK), Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain(ES), France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV), Lithuania(LT), Luxembourg (LU), Hungary (HU), Malta (MT), Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT), Romania (RO), Slovenia (SI), Slovakia (SK), Finland (FI), Sweden (SE), the United Kingdom (UK), Turkey (TR), Norway(NO), Switzerland (CH), Iceland (IS), and Liechtenstein (LI). The WLAN function for this device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.

| AT| BE| BG| CH| CY| CZ| DE| DK
---|---|---|---|---|---|---|---|---
EE| EL| ES| Fl| FR| HR| HU| IE
IS| IT| LI| LT| LU| LV| MT| NL
PL| PT| RO| SE| SI| SK| TR| UK

EU-DECLARATION OF CONFORMITY

Declaration of Conformity

according to directive 2014/34/EU, 2014/53/EU, and 2011/65/EU (2015/863/EU)

The company i.safe MOBILE GmbH declares under its sole responsibility that the product to which this declaration relates is in accordance with the provisions of the following data, directives, and standards:

Name & address of the manufacturer in the EU| i.safe MOBILE GmbH
i_Park Tauberfranken 10 97922 Lauda – Koenigshofen Germany
---|---
Description of the device| Explosion protected smartphone type / IS655.2
model /M655A01
Ex – marking| II 36 Ex is IIC T4 Gc IP54

II 3D Ex is IIIB T135•C Dc IP54

Conformity statement 2014/34/EU issued by

Applied harmonized standards

| EPS 19 ATEX 1 129 X

Bureau Veritas E&E Product Services GmbH Businesspark A96

86842 Tuerkheim, Germany identification number / __ 2004

EN IEC 60079-0:2018; EN 60079-11:2012

Conformity statement 2014/53/EU issued by

Applied harmonized standards

| PHOENIX TESTIAB GmbH _
_32825 Blomberg, Germany
identification number/ 0700
EN 62368-1:2014+A11:2017;
EN 50332-1:2013; EN 50332-2:2013;
EN 50360:2017; EN 50566:2017;
EN 62209-1:2016; EN 62209-2:2010:
EN 62479:2010; EN 50663:2017: ETSI EN 301 489-1 V2.2.3;
ETSI EN 301 489-3 V2.1.1; ETSI
EN 301 489-17 V3.2.4; ETSI EN 301 489-19 V2.1.1;
Draft ETSI EN 301 489-52 V1.1.0;
EN 55032:2015+A11:2020;

EU-DECLARATION OF CONFORMITY

| EN 55035:2017+A11:2020;
ETSI EN 301 511 V12.5.1;
ETSI EN 301 908-1 V13.1.1;
ETSI EN 301 908-2 V13.1.1;
ETSI EN 301 908-13 V13.1.1;
ETSI EN 300 328 V2.2.2;
ETSI EN 301 893 V2.1.1;
ETSI EN 300 330 V2.1.1;
ETSI EN 300 440 V2.2.1;
ETSI EN 303 413 V1.1.1
---|---
Conformity statement 2015/863/EU amending
2011/65/EU issued byApplied harmonized standards| SGS-CSTC
Standards Technical Services Co., Ltd.
Guangzhou Branch Testing Center Chemical Laboratory
198 Kezhu Road, Scientech Park Guangzhou
Economic & Technology Development District
Guangzhou, China 510663
IEC 62321-2:2013; IEC 62321-1:2013;
IEC 62321-3-1:2013; IEC 62321-5:2013;
IEC 62321-4:2013+A1:2017;
IEC 62321-7-1:2015;
IEC62321-7-2:2017 & ISO 17075-1:2017;
IEC 62321-6:2015; IEC 62321-8:2017
CE Marking|