MOBI 70299 Fingertip Pulse Oximeter Instruction Manual

June 6, 2024
MOBI

Fingertip Pulse Oximeter
Model No:
Instruction Manual
Please read this instruction manual completely before operating.

Package Contents

Parts Quantity
1pc Oximeter
1pc Device Strap
2pc AAA 1.5V Batteries
1pc Instruction Manual

Oximeter Specification

Display Type:+A1:B14 OLED display
Sp02
Measurement range: 70% – 99%
Accuracy: ±2% from 70% – 99%, unspecified for readings below

70%
Resolution:| ±1%
Pulse Reader|
Measurement range:| 30BPM – 240BPM
Accuracy:| ±1 BPM or ± 1%
Power supply:| 2AAA 1.5V batteries
Dimensions:| 60 x 35 x 35 mm
Environment|
Operating Temperature:| 1°F – 102°F (5°C – 40°C)
Storage temperature:| 14°F – 102°F (-10°C – 40°C)
Operation humidity:| 15% – 80%
Storage humidity:| 10% – 80%
Air pressure:| 70 – 106 kPa

Measurement Preparation For Best Results

Instructions For Safe Operation & Use

  • Service of this device should be completed by qualified service personnel, do not attempt to service this pulse oximeter yourself.
  • Do not use the oximeter in situations where an alarm notification may be needed.
  • Prolonged use of the oximeter may require a periodical change to the site of the sensor.
  • It is recommended to change the sensor site, check skin integrity, circulatory status, and correct alignment at least every two hours.
  • Sp02 measurements may be adversely affected in the presence of high ambient light, therefore, shielding the Oximeter from light during use.

The following medical reasons may cause inaccurate measurements and should be avoided:

  • Placement of a sensor on an extremity with a blood pressure monitor/cuff, arterial catheter, or another intravascular line.
  • The patient has hypotension or severe vasoconstriction, anemia, or hypothermia.
  • The patient is in cardiac arrest.

Note: Fingernail polish or false nails may cause inaccurate Sp02 readings.

Installation, Setup & Operation

The MOBI Fingertip Pulse Oximeter is intended for non-invasive spot-check measurement of functional oxygen. It is used to measure human hemoglobin (Hb) saturation (Sp02) and pulse rate (HR) through the finger. This product is suitable for personal and clinical use (e.g. hospital, surgery, pediatrics, etc.)

Figure 1. Front panel & display description

Installing/Replacing Battery

  • Remove the battery cover by sliding it toward the bottom of the unit.
  • Insert or replace 2 x AAA batteries into the battery compartment, ensuring to match the indicating polarity symbols visible on the device. The springs are not an indicator of battery direction. (Always replace batteries with new, unused batteries).
  • Place the battery cover on the unit and slide back in place so it snaps closed.

Operating The Oximeter

  • Squeeze the white end of the unit to open the clamp.
  • Place the unit on the patient’s finger, inserting the finger as far as comfortable, covering the black rubber and sensor. The fingernail should be facing up towards the top (OLED screen).
  • Release the clamp and allow the device to close on the finger.
  • Turn on the device by pressing the ‘power’ button.
  • Device will display Sp02 and HR.

Turning Off the Unit

  • The unit will automatically be powered off when the device has not been used for longer than 10 seconds

Changing OLED Display and Direction

  • This device has six screen options to ease the viewing of the measurements while on a patient.
  • To switch the screen view. While the unit is turned on with the home screen being displayed, short
  • press the ‘power’ button to navigate through the screen display options.

Attaching the Strap

  • At the clamp end of the oximeter, on the base of the device, you will find a small hole in the center of the base.
  • Thread the thin loop through the hole and feed the strap back through itself to attach the strap.

Editing Settings

  • To enter the settings menu, long-press the ‘power’ button (>0.5seconds).
  • There are two sub-menus: alarm settings and sound settings.
  • To navigate through the menu, move the ‘*’ symbol by pressing the ‘power’ button
  • Short press the ‘power’ button to move up and down the menu. Long press the ‘power’ button to change the specific setting the ‘*’ symbol is on.
  • Long press the ‘power’ button when the ‘*’ is next to the menu name (alarm/sound) to switch between the sub menus.

Care & Maintenance

  • For best results, replace the batteries when a low voltage symbol is displayed.
  • Clean the surface of the fingertip oximeter between each use, using an alcoholic wipe/swab
  • Do not wet or use water to clean this device directly.
  • Remove the batteries, if you will not operate the oximeter for an extended period to reduce the risk of a battery leak.
  • If storing the device, keep the oximeter in an environment with temperatures between (14 104°F) and humidity between 10 – 80%.

Note: Please follow local and state guidelines regarding battery disposal.

Product Declaration

Guidance and manufacturers declaration – electromagnetic radiation for other equipment and systems

The MOBI Fingertip Pulse Oximeter is designed to be used in specified electromagnetic environments. Users of the unit must use it in the following environments:

Radiation Test Compliance Electromagnetic Environment – guidance
RF interference CISPR 11 Group 1 RF signal of the Fingertip Pulse Oximeter

is simply created by its internal function. Therefore, its RF interference is very low and is not likely to cause any interference to nearby electronic equipment
RF interference CISPR| Class B| The Fingertip Pulse Oximeter applies to all establishments,
including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes

Warnings

WARNING: Explosion Hazard: Avoid extreme heat or fire, batteries are flammable and may cause
WARNING: Do not attempt to recharge normal dry-cell batteries, this may cause a leak and may cause fire.
WARNING: Do not use the unit in an MRI or CT

Limited Product Warranty
MOBI® warrants its products to be free from defects in material and workmanship for a period of (1 Year) from the date of purchase. Should the product prove to be defective at any time during the warranty period, we would either replace or repair the product at our option without charge. After the warranty period, a service charge will apply for the replacement of parts and labor costs. To obtain warranty service, you must return the product complete with its original parts & accessories along with a copy of the original purchase, gift, or registry receipt to us. This warranty does not cover damage caused by any tampering, accident, misuse, abuse, improper maintenance, unauthorized modification, or connection to an improper power supply. There will be a charge for repair caused for such damage. This warranty excludes all incidental or consequential damages and any liability other than stated above.
Questions?
Please visit: www.getmobi.com
Email: service@getmobi.com

Note:
For a detailed instructional manual please follow this link:http://www.getmobi.com/users-manuals

© 2021 MOBI Technologies, Inc.
All Rights Reserved

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals