MICHELIN CAI 713517 Mems Data Capture Wand+ Receivers Instructions

MICHELIN CAI 713517 Mems Data Capture Wand+ Receivers Instructions

PRODUCT NAME

MEMS DATA CAPTURE WAND+ Basic – Part Number CAI 713517

PRODUCT DESCRIPTION

The MEMS DATA CAPTURE WAND+ receives, via internal antennas, pressure and temperature data transmitted by the MEMS sensors. This information is to be forwarded to the MEMS EVOLUTION4 mobile application through Bluetooth Low Energy, together with any messages that may require corrective action to be taken in order to maximise the service life of the tire.

PRODUCT SPECIFICATION

Radio Frequency Characteristics

• RF sensor reception : 433.92 MHz
  Trigger for sensor : 125 Khz

• BLE frequency: 2.4 GHz

Electrical Performance

• Battery: Li-ion rechargeable 7.4V, 2600mAh (UN3480)
  Typical battery performance:

  3 weeks in stand-by mode
  8 hours in normal operation

Charging parameter

• Use DC 12v / 1A charger 12W max- The DC supply must be ES1 and PS2 according to IEC62368-1 standard
• plug Jack 5.5 x 2.1 x 12 mm DC
• Indoor operation within temperature range: 0°C / +40°C (32°F / +104°F)
• Typical battery charging time: 4.5 hours to achieve full charge

Physical Characteristics

• Approximate dimensions: Long= 250mm Width=95mm Height=50mm
• Approximate weight: 400g

Operating Conditions in normal Autonomous mode :

• Temperature: -20°C to +40°C (-4°F to / +104°F)
• Indoor or outdoor use – IP 44

IP44 means product is protected against ingress of solid foreign objects ≥1mm and against ingress of water with harmful effects splashing.

Storage condition:

• Temperature 1 year : -20°C / +25°C (-4°F / 77°F)
• Temperature 3 months : -20°C / +45°C (-4°F / 113°F)

Warning/Caution: Do not try to replace internal battery of MEMS DATA CAPTURE WAND+ Battery replacement can only be done by skilled and trained people, with only appropriate specific battery designed for this device. Contact MEMS representative if it has to be done. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Risk of fire explosion or burns.

Meaning of the symbols on the device:

 Barred bin : the device must not be thrown away with normal waste.
It must be recycled
 CE : Product complies with EU requirements

FCC ID : FI5-WAN02-1

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference
(2) this device must accept any interference received, including interference that may cause undesired operation

Any changes or modifications to this equipment not expressly approved by MICHELIN may cause, harmful interference and void the FCC authorization to operate this equipment

This portable equipment with its antenna complies with FCC’s radiation exposure limits set forth for an uncontrolled environment. To maintain compliance, follow the instructions bellow:
(3) This transmitter must not be co-located or operating with any other antenna or transmitter
(4) Avoid direct contact to the antenna, or keep contact to a minimum while using this equipment

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

ISED ID : 5056A-WAN021

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.

This portable equipment with it’s antenna complies with RSS102’s radiation exposure limits set forth for an uncontrolled environment. To maintain compliance, follow the instructions below :
(1) This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
(2) Avoid direct contact to the antenna, or keep contact to a minimum while using this equipment

DISPOSAL

The MEMS DATA CAPTURE WAND+ must not be disposed of in landfill.

At the end of its life, the MEMS DATA CAPTURE WAND+ must be deposited in a container dedicated to the recycling of electronic equipment that contains batteries. If users do not have access to the appropriate recycling facility, your local Michelin MEMS representative is able to provide a container dedicated to the purpose of collecting MEMS equipment.

CONTACT

For more information or assistance, please contact the Michelin MEMS representative for your country.

Brasil, Chile & Perú : +55 (21) 36 21 4646
USA, Canada & México : +1 864 458 5000
Australia : +61 3 86 71 1003
South Africa : +27 115 790 300
Russia : +7 495 258 09 26
China : +86 21 22855000
Europe : +33 4 73 32 20 00

Features, specifications are subject to change without notification.

MFP MICHELIN © 2021 All rights reserved.
Exclusive property of Manufacture Française des Pneumatiques Michelin. Any reproduction or utilization prohibited without the consent of Michelin.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>