MICHELIN 847142 Programmable Rapid 4X4-SUV Digital Tyre Inflator User Guide

MICHELIN 847142 Programmable Rapid 4X4-SUV Digital Tyre Inflator

Please read the operating instructions carefully before using your inflator. Improper use can cause damage to property and possibly harm the user. When using the inflator ensure the vehicle is parked in a safe location, off the road, with the vehicle handbrake on and where your personal safety is not at risk.
Only suitable for vehicles with negative earth. Check your vehicle owner’s manual.

This inflator can inflate vehicle tyres up to 80 PSI (please follow your vehicle manufacturer’s recommendations) and bicycle tyres up to 100 PSI. Higher pressures can be achieved in cycle tyres due to their smaller air volumes compared to vehicle tyres.
When inflating vehicle tyres this inflator should ONLY be used for car tyres and bicycle tyres. Low-pressure items such as sports balls and small inflatable toys may also be inflated using the adaptors provided.

WARNING! COMPRESSED AIR CAN BE DANGEROUS
This appliance is not intended for use by persons (including children) with lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Never allow children to use this tyre inflator. Children should be supervised to ensure that they do not play with the appliance.
Never leave unattended when running.
Never overinflate.
Always use in a safe area away from traffic and other dangers.
Never run for more than 10 minutes. After each 10-minute run allows the inflator to cool for 10 minutes.

WARNING! ENSURE CORRECT TYRE PRESSURES
Correct tyre pressure is vital for road safety.
Under or over-inflated tyres can be dangerous.
Always ensure that regular weekly checks are carried out to the vehicle manufacturer’s recommended pressures, including the spare. Always check before a long journey or after loading or unloading the vehicle.
Always check pressures in an ambient temperature, never immediately after a long journey.
CAUTION
Inspect the tyre inflator before each use.
Please ensure that your cigarette lighter socket is clean and free of debris, failure to do this may cause overheating of the plug.
If your 12V power socket has a fuse rated at 10A or less, the wiring in your vehicle will not support this product.
Do not leave the device unattended whilst connected to a 12V DC socket.
Do not kink or block the air hose while the compressor is working.
Do not use the compressor if bent, broken, melted, burnt, wet or any of the components are damaged.
Only use the adaptors supplied with the device.
The compressor contains no user-serviceable parts – DO NOT OPEN.

This product conforms to the criteria set out in Noise Emission by Outdoor Equipment Directive 2001/14/EC, ROHS DIRECTIVE 2011/65/EC AND EMC DIRECTIVE 2014/30/EC.

OPERATING FEATURES

1. PSI, BAR & kPa / Reset button
2. White LCD digital display
3. Superbright LED lights
4. Storage compartment
5. Cushioned feet for stability
6. 300 cm (approx.) power cord with fused 12V power plug
7. LED light On/Off button
8. On/Off button
9. Tyre valve dust cap holder 10 Pressure pre-set buttons
10. Tyre valve connector
11. 65 cm (approx.) high-pressure air hose
12. Bleed valve
13. Adaptors (snap-in storage). Located in the storage compartment (4)

SPECIFICATIONS:

• Max pressure: Up to 80 PSI for vehicle tyres (please follow your vehicle recommendations)
• Pressure accuracy: Backlit pressure gauge (+/- 1 PSI up to 50 PSI, +/- 2 PSI > 50 PSI to 80 PSI)
• Pressure resolution: PSI / BAR / kPa
• Max current: 14A / 168W
• Fuse size: 15A glass
• Hose length: 65 cm (approx.)
• Power cord: 300 cm (approx.)

TO INFLATE VEHICLE TYRES:

1. Unwind the power cord completely from the storage compartment (4) 12V power socket (some vehicles may require the ignition to be on to compartment door can be replaced as there is a cut-out for the power damage. After a few seconds, the digital display (2) will momentarily s return to 0.00. It is good practice to press and hold the reset button (1 the digits will be displayed again momentarily and return to 0.00.

2. Press the PSI, BAR & kPa buttons (1) to select the desired pressure.

3. Remove your tyre valve dust cap and store on the handy holder on to sure your tyre valve is clean before removing the high-pressure hose always make sure you connect the 12V power plug before conne hose to your tyre valve. Screw the tyre valve connector (11) on and display (2) will show your current tyre pressure. If the display shows 0 Trouble Shooting guide. If this is the correct pressure stated in your v simply remove the tyre valve connector (11) and replace your dust ca

4. If the tyre is below the recommended pressure (as specified in your v either the – or + pre-set button (10) to adjust to set the correct tyre pr for 1 second will increase/decrease the pre-set pressure rapidly.

5. If the tyre is above the recommended pressure the high-pressure h handy bleed valve (13) that allows you to lower the pressure of pressure is shown on the digital display (2).

6. Switch on the inflator which will now inflate your tyre until the selected continues to run for a few seconds when it has reached the selected p the in-built pressure sensor to ensure the correct pressure has been
   Note: Although the inflator is fully automatic do not leave the inf inflating your tyre.

7. If you are inflating multiple tyres, then follow the procedure 3. to 6. ab (6) is disconnected, then always reconnect the 12V power supply (6) pressure hose (12) to your tyre valve. Remember you may have to re some vehicles have different pressures between front and rear tyres, vehicle’s handbook). If there is a power interruption during the inflation reset procedure outlined in the Trouble Shooting guide.

Note: The inflation unit will default to the PSI pressure format when removed from the power source.

ADAPTORS

Included with your MICHELIN Programmable Rapid 4X4/SUV Digital Tyre Inflator, at the front of the unit, is a storage compartment for the power cord. The storage compartment lid (4) holds various adaptors to enable you to inflate other items.

12V POWER PLUG

TO REPLACE THE FUSE IN THE 12V PLUG:

Unscrew plastic nose anti-clockwise

Replace the fuse with the same 15A rating. Screw back on the plastic nose

TYPICAL INFLATION PRESSURE

CONVERSION CHART

TROUBLESHOOTING

OTHER MICHELIN PRODUCTS AVAILABLE:

References

• Michelin Lifestyle

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>