fontastic 260568 Saya Portable Wireless Soundbar User Manual

fontastic 260568 Saya Portable Wireless Soundbar

instructions

Thank you for choosing the SAYA wireless soundbar. The soundbar offers the possibility to receive music wirelessly and has a USB port, Micro SD card slot, AUX port, and radio function. Please read the operating instructions carefully and observe the safety instructions.

Package contents

• Soundbar SAYA
• Micro USB charging cable
• 3,5 mm jack audio cable
• User manual

Overview

1. Multifunction button
2. Previous title / Volume –
3. Next title / Volume +
4. Play/Pause/Station search
5. LED display
6. Micro USB charging port
7. AUX connector
8. TF card slot
9. USB port
10. On/Off switch
11. Subwoofer
12. Speaker

Getting started

Charging the battery SAYA is equipped with an internal rechargeable battery. Connect the micro USB cable, which is included in the delivery, to the micro USB charging port of the SAYA (6). The USB plug of the cable can be connected to a computer or standard USB power supply. The red charging LED will light up during charging. The usual charging time is 2-3 hours. When fully charged, the red LED will turn off.

Switching On /Off

• Switch on: When powered off, switch the button (10) to the ,, ON” position.
• Switch off: Switch the button (10) to the “OFF” position.

Pairing with a Bluetooth® source

The speaker must be connected to a Bluetooth® device before it can be used for wireless music streaming.

1. Switch on the loudspeaker by setting the On/Off switch (7) to,, ON”. The speaker automatically switches to pairing mode.
2. Search for Bluetooth® audio devices with your Bluetooth® device from which audio data is to be played.
3. The searching Bluetooth® indicates that it has found the speaker,, SAYA”.
4. Confirm the pairing with,, SAYA”. Enter,,0000″ if you are asked for a code.

When using a Bluetooth® device without a display, switch it to pairing mode and wait a few seconds for the connection with the speaker to be established.
NOTE: If the connection is lost or the transmitter is disconnected for a short time, turn the speaker off and on again. After switching off and on again, both devices connect automatically.

TWS function

With the TWS function, you can connect two SAYA with each other to output the music through two devices. To connect two speakers, tum on both devices simul­taneously and long-press the multifunction button (1) in pairing mode. The devices connect, this is indicated by an acoustic signal. Then pair one of the two SAYAs with the audio source. After a successful connection, the audio data is output via both speakers.
Attention: When first TWS pairing the loudspeakers, the Bluetooth® function of your smartphone must be switched off while the TWS connection is being set up. Activate the Bluetooth® function after both speakers are connected via TWS. To pair the speakers and the smartphone, follow the steps described in the,,Pairing” section.

Music playback

Playing music via Bluetooth® A Bluetooth® source must be paired with SAYA to receive and output music wirelessly! Play or pause the music playback by briefly pressing the Play/Pause button (4). Note: For music streaming, the audio source must support the A2DP profile. Music control To play or pause music, briefly press the Play/Pause button (4). To skip to the next title, briefly press the Next title key(3). To skip to the previous title, briefly press the Previous title key (2). Note: The phone must support A2DP and AVRCP profile to play and control music through the SAYS speaker.

Playback from Micro SD card

1. Place a Micro SD card in the card slot of the SAYA (10).
2. The device will automatically switch to SD mode and the music will be output from the speaker.

Playback from USB

1. Place a USB stick in the USB port (11) of the SAYA.
2. The device will automatically switch to SD mode and the music will be output from the speaker.

Playback via AUX Connect the device from which the music is to be played to the AUX port (7) of the soundbar using the cable included in the scope of delivery. Start the music playback on the audio source. The music is now output via the soundbar.

FM Radio

1. Tum on the speaker by selling the On/Off switch (10) to,, ON”.
2. Please connect the Micro USB cable. II serves as an antenna lo receive the FM signal better.
3. Press the multifunction button (1) to switch to FM mode.
4. Long press the, Play/Pause” button (4) to start an automatic station search. At the end of the search, receivable stations are automatically stored.
5. In radio mode, press,,+” or,,-” to search for the desired station.

Hands-free function

Due to the built-in microphone, the speaker is ideally suited to be used as a hands-free speaker for phone calls.
Note: High volume may cause feedback with the microphone. This will cause echo on the phone side, not on the speakerphone side.

Accepting/ending a call To answer an incoming call, press the Play/Pause button (4). To end an ongoing call, press the Play/Pause button (4).

Adjusting the Volume

• Press and hold the volume+ button (3) to increase the volume.
• Press and hold the volume – button (2) to decrease the volume.

Technical Data

•  BT V: 5.0
• Input: 5V DC / 500mA
• Speaker: 2 x 5W
• Frequency: 100Hz-20kHz
• LED Display
• 3.5 mm audio line-in
• FM Radio
• Micro SD card slot
• USB port
• Hands-free function
• TWS function
• Battery: 1200 mAh
• Housing material: ABS
• Dimensions: 400 x 65 x 65 mm
• Weight: 675 g

Safety information

• Never open the device.
• Do not submerge the device in water and keep ii away from moisture.
• Never forcibly connect a cable.
• Place the device only on flat surfaces.
• Remove electronic devices from the power supply if they will not be used for a length of time.
• Do not use the device if ii exhibits visible damage.

No liability is accepted for any damage which may occur through the improper operation. If you require technical support, please contact our support team via email at service@fontastic.eu.

Registration and Safety Certification/General Information

We hereby declare that this device carries the CE mark in accordance with the regulations and standards. II conforms with the funda­mental requirements of the RED 2014/53/EU. The full text of the EU declaration of conformity is availa­ble at the following internet

Note on environmental protection

After the implementation of the European Directive 2012/19/EC in the national legal system, the following applies: Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details of this are defined by the national law of the respective country. This symbol on the product, the instruction manual, or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilizing old devices, you are making an important contribution to protecting our environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>