YYS2521 YI Home Camera User Guide
- June 6, 2024
- YI
Table of Contents
Thank you for choosing YI Home Camera 3
In the box
Product Configuration
Parts Description
- Reset: Press and hold the Reset button for 5 seconds or until the indicator light turns yellow.
- Indicator light: solid (yellow) – camera on; flashing (yellow) – ready to connect to WiFi network; flashing (blue) – connecting to WiFi network; solid (blue) – connected to WiFi network.
It is recommended that you insert an 8-32GB Micro SD card. Otherwise, important functions such as saving videos and viewing saved videos cannot be performed.
Basic Instructions
a) Turning the camera on
Plug the camera into a power outlet using the power cable and adapter. The
indicator light will turn on when the camera receives power.
b) Pairing with YI Home app
- Download the YI Home app from Googe Play Store or App Store, or scan the QR code below and follow onscreen instructions to install
- If you have a YI account, log in directly and add a device based on the prompts in the interface. Otherwise, please sign up for a YI account first.
YI Home app QR code
c) Adding a device to your YI account
Note: You must connect the camera to a 2.4GHz band network to
successfully pair. 5GHz band networks are not supported.
- Log in to the YI Home app and navigate to the device selection interface to add a camera.
- Select YI Home Camera 3.
- Tap the ‘I heard Waiting to connect’ icon on the app when the voice prompt indicates that the camera is ready to connect.
- Use the YI camera to scan the QR code displayed on your phone.
- Once the QR code has successfully scanned, tap ‘Next’. The voice prompt will indicate that the camera is connected.
Caution
-
Do not place the camera near a microwave oven.
-
Do not place the camera in an environment with tangled wires, such as audio cables, video cables, and USB cables, and keep as far away as possible from cables.
-
Make sure that you are in a place that is as close as possible to the WiFi signal coverage.
Switching network environment -
If you want to connect the camera to a different WiFi network, hold the reset button for 5 seconds or until the indicator light turns yellow to reset the camera. Follow the pairing process again to connect to the new network.
Installation notes
Magnetic base: attach the camera base to a metal surface to mount
This device complies with Part 15 of the FCC Rules / Industry Canada license-
exempt RSS standard(s). Operation is subject to the tollawlig two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, during interference that may cause undesired
operation. Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
MPE Requirements
To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm
or more should be maintained between the antenna of this device and persons
during device operation.To ensure compliance, operations at doser than this
distance is not recommended.
IC WARNING
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the device
The distance between user and products should be no less than 20cm
Manufacturer: Shanghai Xiaoyi Technology Co., Ltd.
Address:
Building 18, Lane 55 Chuanhe Road, China(Shanghai) Pilot
Free Trade Zone, Shanghai, China, 201203
Website: www.yitechnology.com
Y26GA EU V1.0 FCC ID: 2AFIB-YYS2521
IC: 20436-YYS2521
KEVIN: YES. 2521