Bissell 2513, 2694 Series Spotclean Little Green Vacuum User Guide
- June 8, 2024
- Bissell
Table of Contents
- IMPORTANT SAFETY INSTRUCTIONS
- What’s In The Box?
- Product View
- Cleaning Formula
- Assembly
- Filling the Clean Water/Solution Tank
- Pre-Treating
- Cleaning with Tools
- Cleaning with Stain Trapper Tool
- Cleaning with LED Spraying Crevice Tool
- Emptying the Dirty Water Tank
- Cleaning the Float Stack
- Thermal Protector
- Troubleshooting
- Warranty
- Service
- Register your product today!
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SPOTCLEAN®, LITTLE GREEN®
USER GUIDE 2513, 2694 SERIES
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR PORTABLE CARPET CLEANER.
When using an electrical appliance, basic precautions should be observed,
including the following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:
» Connect to a properly grounded outlet only. See grounding instructions. Do
not modify the three-prong grounded plug.
» Do not leave appliance when it is plugged in. Unplug from outlet when not in
use and before servicing.
» Do not expose to rain. Store indoors.
» Do not allow to be used as a toy. Close attention is necessary when used by
or near children.
» Do not use for any purpose other than described in this user guide. Use only
the manufacturer’s recommended attachments.
» Do not use with damaged cord or plug. If the appliance is not working as it
should, has been dropped, damaged, left outdoors, or dropped into water, have
it repaired at an authorized service center.
» Always install float before any wet pick-up operation.
» Do not pull or carry by cord, use cord as a handle, close a door on cord, or
pull cord around sharp edges or corners. Do not run appliance over cord. Keep
the cord away from heated surfaces.
» Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
» Do not handle plug or appliance with wet hands.
» Do not put any object into openings. Do not use with any opening blocked;
keep openings free of dust, lint, hair, and anything that may reduce airflow.
» Keep hair, loose clothing, fingers, and all parts of body away from openings
and moving parts.
» Turn OFF all controls before plugging or unplugging appliances.
» Use extra care when cleaning on stairs.
» Do not use to pick up flammable or combustible materials (lighter fluid,
gasoline, kerosene, etc.) or use in areas where they may be present.
» Do not use the appliance in an enclosed space filled with vapors given off
by oil-based paint, paint thinner, some moth-proofing substances, flammable
dust, or other explosive or toxic vapors.
» Do not use to pick up toxic material (chlorine bleach, ammonia, drain
cleaner, etc.).
» Do not pick up anything that is burning or smoking, such as cigarettes,
matches, or hot ashes.
» Use only BISSELL® cleaning products intended for use with this appliance to
prevent internal component damage. See the Cleaning Fluid section of this
guide.
» Keep appliance on a level surface.
» Risk of fire and chemical burn hazard. Keep batteries out of reach of
children and in the original package until ready to use. Do not recharge,
disassemble, heat above 60°C (140°F), or incinerate batteries. The batteries
can explode in a fire. The battery terminals are not to be short-circuited.
Dispose of used batteries safely and promptly. Even used cells may cause
injury.
» This attachment contains a lithium button/coin cell battery. If a new or
used lithium button/coin cell battery is swallowed or enters the body, it can
cause severe internal burns and can lead to death in as little as two hours.
Always completely secure the battery compartment. If the battery compartment
does not close securely, stop using the product, remove the batteries, and
keep them away from children. If you think batteries might have been swallowed
or placed inside any part of the body, seek immediate medical attention.
» Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burns.
» Unplug the appliance and disconnect the accessory. Remove battery cover to
replace the batteries. Observe battery polarity when replacing batteries.
» If the attachment is to be stored for a long period, the batteries should be
removed. Different types of batteries or new and used batteries are not to be
mixed. The battery must be removed from the accessory before it is scrapped.
» Never put batteries in mouth. If swallowed, contact your physician or local
poison control.
» Replace the battery with CR1632 only. Use of another battery may present a
risk of fire or explosion. CR1632 cells may be purchased any where batteries
are sold.
» Plastic film can be dangerous. To avoid the danger of suffocation, keep away
from children.
» Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner,
etc.).
» Do not use the appliance in an enclosed space filled with vapors given off
by oil base paint, paint thinner, some moth-proofing substances, flammable
dust, or other explosive or toxic vapors.
» Do not pick up hard or sharp objects such as glass, nails, screws, coins,
etc.
» Liquid must not be directed towards equipment containing electrical
component s.
» Do not immerse. Use only on surfaces moistened by the cleaning process.
» Use only the type and amount of liquids specified under the operations
section of this guide.
» Use only on carpet moistened by the cleaning process.
» Recycle batteries, do not mix with household waste.
» The battery is to be disposed of safely.
» Do not incinerate the accessory even if it severely damages. The batteries
can explode in a fire.
SAVE THESE INSTRUCTIONS FOR FUTURE USE
This model is for household use only. Commercial use of this unit voids the
manufacturer’s warranty.
WARNING
Improper connection of the equipment-grounding conductor can result in a risk
of electrical shock. Check with a qualified electrician or service person if
you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If
it will not fit the outlet, have a proper outlet installed by a qualified
electrician. This appliance is designed for use on a nominal 120-volt circuit
and has a grounding attachment plug that looks like the plugin illustration.
Make certain that the appliance is connected to an outlet having the same
configuration as the plug. No plug adapter should be used with this appliance.
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded wiring system. If it should
malfunction or break down, grounding provides a safe path of least resistance
for electrical current, reducing the risk of electrical shock. The cord for
this appliance has an equipment-grounding conductor and a grounding plug. It
must only be plugged into an outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Thanks for buying a BISSELL® portable carpet cleaner!
We love to clean and we’re excited to share one of our innovative products
with you. We want to make sure your portable carpet cleaner works as well in
two years as it does today, so this guide has tips on using, maintaining, and
if there is a problem, troubleshooting. In just a few simple assembly steps,
you’ll be ready to spot clean. Flip to page 6 and let’s get started!
What’s In The Box?
NOTE: Standard accessories may vary by model. To identify what should be included with your purchase, please refer to the “Carton Contents” list located on the carton top flap.
Product View
-
Clean Water/Solution Tank
-
Power Button
-
Dirty Water Tank
-
Flex Hose
-
Flex Hose Clip
-
Power Cord
-
Quick Release™ Cord Wrap
-
Hose Grip Bracket
Cleaning Formula
WARNING To reduce the risk of fire and electric shock due to internal component damage, use only the BISSELL® cleaning formula intended for use with this machine.
Keep plenty of genuine BISSELL Spot & Stain Cleaner formula for portable carpet cleaning machines on hand so you can clean whenever it fits your schedule. Always use genuine BISSELL cleaning formulas.
NOTICE : Use of cleaning formulas that contain lemon or pine oil may damage this appliance and void the warranty. Chemical spot cleaners or solvent-based soil removers also should not be used. These products may react with the plastic materials used in your cleaner, causing cracking or pitting.
Assembly
WARNING Do not plug in your cleaner until you are familiar with all instructions and operating procedures.
Filling the Clean Water/Solution Tank
NOTE: Follow the fill lines on your Clean Water/Solution Tank to add the correct amount of hot tap water (140 degrees F / 60 degrees C MAX) and portable machine formula. Note: There are different directions on the tank for small and large messes. DO NOT BOIL OR MICROWAVE WATER.
Pre-Treating
IMPORTANT: Check the manufacturer’s tag before cleaning upholstery. “W” or “WS” on the tag means you can use your cleaner. If the tag is coded with an “S” (with diagonal strike-through), or says “Dry Clean Only,” do not proceed. If the manufacturer’s tag is missing or not coded, check with your furniture dealer.
WHY PRETREAT? Cleaning effectiveness will be enhanced if you pre-treat heavily stained or highly soiled areas.
NOTE : When pre-treating with the Deep Reach Tool or Deep Stain Tool, it should be kept in contact with the carpet as noted on the next page.
Cleaning with Tools
WARNING Keep the spray away from the face. Failure to do so may result in
personal injury.
CLEANING WITH THE 3″/4” Tough Stain Tool
Attach the 3”/4” Tough Stain Tool to the handheld cleaning hose. Press the
spray trigger to mist solution over and onto the soiled area. Release spray
trigger and gently scrub the stain.
To lift the stain away, apply downward pressure on the tool and slowly pull it
toward you. Then use “drying strokes” (by not pressing down the trigger) to
remove the remaining moisture. Repeat as needed.
CLEANING WITH THE DEEP STAIN/REACH TOOL (select models)
Attach the Deep Stain/Reach Tool to the cleaning hose. Set the tool directly
on top of the carpet before pulling the spray trigger to inject formula deep
into the carpet fibers.
Always keep the tool in direct contact with carpeting to avoid over-spraying.
CLEANING WITH THE 3-N-1 STAIR TOOL (select models)
Attach the 3-n-1 Stair Tool to the cleaning hose. This versatile 3-way tool
sprays, scrubs and suctions up dirt and stains from the outer curves, corner,
and tread of a carpeted stairs. Twist the tool head to the desired setting to
clean. The downward-facing edge is the active cleaning mode: (a) use the flat
area to clean the top of the stairs, (b) use a pointed edge to clean the
inside of the crevice, (c) use an indented area to clean the outer corner.
CLEANING WITH THE HYDRORINSE™ TOOL (select models)
Attach the HyrdoRinse™ tool to the cleaning hose. Hold the hose and attachment
in an upright position. Then hold down the trigger to rinse the hose for 30
seconds.
The HydroRinse tool can be stored on the right handle or on the hose in
between use.
NOTE : Ensure that the cleaning solution and water are in the tank before
use.
Cleaning with Stain Trapper Tool
WARNING Keep the spray away from the face. Failure to do so may result in personal injury.
CLEANING THE STAIN TRAPPER TOOL : Clean the front of the tool by removing the plate over the suction plate. Pull down to remove and rinse with water. Then replace the plate by sliding it back into place.
Cleaning with LED Spraying Crevice Tool
Pull tabs out of the battery door area before use to activate. Connect to the
end of the hose and the LED Light will automatically turn on. Pull the trigger
to the spray solution. Scrub and suction the area to lift and remove the
stain.
To replace the LED battery, unscrew the small screw with a Phillips-head
screwdriver. Pull the cover off to reveal two batteries (CR1632 3V). Slide and
pull out each battery and replace it with new. Be sure the “+” sign on the
battery is facing out.
Dispose of used battery promptly. Keep away from children. Do not disassemble
and do not dispose of in fire.
Emptying the Dirty Water Tank
WARNING To reduce the risk of electric shock, turn the power OFF and disconnect from the electrical outlet before performing maintenance or troubleshooting.
NOTE : Store unit is a protected, dry area at room temperature (40
degrees F to 110 degrees F).
NOTICE To reduce the risk of a leaking condition, do not store a unit
where freezing may occur. Damage to internal components may result.
Cleaning the Float Stack
WARNING To reduce the risk of electric shock, turn the power OFF and disconnect from the electrical outlet before performing maintenance or troubleshooting.
Thermal Protector
An internal thermal protector has been designed into your carpet cleaner to protect it from overheating. When the thermal protector activates, the suction motor will stop operating. If this happens proceed as follows:
NOTE : If the thermal protector continues to activate after following the above steps, your cleaner may need servicing. Call BISSELL® Consumer Care or visit the website.
Troubleshooting
WARNING To reduce the risk of electric shock, turn the power switch OFF and disconnect from the electrical outlet before performing maintenance or troubleshooting checks.
Problem
| Possible causes|
Remedies
Reduced Spray or No Spray| Spray nozzle clogged.| Clean spray nozzle using an
unfolded paper clip.
Clean Water/Solution Tank empty.| Check/fill tank.
Clean Water/Solution Tank insert clogged.| Clean insert at bottom of Clean
Water/ Solution Tank.
Pump needs priming.| Gently lift Clean Water/Solution Tank while depressing
the spray trigger OR gently squeeze clean tank while depressing spray trigger.
Clean Water/Solution Tank not fully seated.| Remove and reinstall Clean
Water/Solution Tank.
Carpet Cleaner Won’t Pick Up Cleaning Solution| Poor upholstery/carpet tool
position.| Reposition upholstery/carpet tool on surface, follow recommended
cleaning procedures.
Dirty Water Tank is full.| Empty Dirty Water Tank.
Excess solution in flex hose.| Lift tool and point upwards to allow water in
hose to flow into the Dirty Water Tank.
Incorrect cleaning formula.| Use BISSELL® 2X Portable Machine formulas only.
Dirty Water Tank is improperly seated onto base.| Remove Dirty Water Tank and
reseat onto unit.
Dirty tank plug is unplugged.| Push in Dirty Water Tank plug until properly
sealed.
Deep Reach Tool is Over-Spraying Formula (Formula is Spraying Out the
Sides)| Formula trigger is being pulled when tool is above carpeting.| Make
sure the Deep Reach Tool’s formula injection needles are burrowed deeply
within your carpeting before pressing the formula spray trigger. To avoid
over-spraying, make sure the tool stays in direct contact with the carpet at
all times.
Deep Reach Tool is being used on upholstery.| The Deep Reach Tool is designed
for highpile carpets and rugs. Switch to the 3” Tough Stain Tool for
upholstery cleaning.
Dirty Water Tank Leaking| Duckbill valve is dirty.| Clean the duckbill valve
that is located at the bottom of the Dirty Water Tank. Once cleaned, make
sure it is placed securely back in place.
Float stack not fully locked on Dirty Water Tank.| Remove float stack and
twist until the arrow is aligned with lock symbol on Dirty Water Tank pg. 12.
Dirty Water Tank not properly seated onto machine.| Remove and reseat onto the
unit.
Warranty
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL® Consumer Care by E-mail or telephone as described below.
It may be necessary to obtain some of your personal information, such as a mailing address, to fulfill the terms of this warranty. Any personal data will be handled pursuant to BISSELL’s Privacy Policy, which can be found online at www.BISSELL.com/privacy-policy.
Limited Two-Year Warranty
Subject to the *Exceptions and Exclusions from the Terms of the Limited Warranty, upon receipt of the product, BISSELL will repair or replace (with new, refurbished, lightly used, or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for two years, any defective or malfunctioning part.
See information below on “If your BISSELL product should require service”.
This warranty applies to products used for personal, and not commercial or rental, service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the user guide is not covered. This warranty will only be valid if the product is used in the same country in which it was sold.
BISSELL is not liable for incidental or consequential damages of any nature associated with the use of this product. BISSELL’s liability will not exceed the purchase price of the product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
*Exceptions and Exclusions from the Terms of the Limited Warranty
This warranty is exclusive and in lieu of any other warranties, either oral or written. Any implied warranties, which may arise by operation of law, including the implied warranties of merchantability and fitness for a particular purpose, are limited to the twoyear duration from the date of purchase as described above.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
NOTE : Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim.
Service
Please do not return this product to the store.
Other maintenance or service not included in the manual should be performed by
an authorized service representative.
If your BISSELL product should require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in
your area. If you need information about repairs or replacement parts, or if
you have questions about your warranty, contact BISSELL Consumer Care.
Website: www.BISSELL.com/service-centers
E-mail: www.BISSELL.com/email-us
Call: BISSELL Consumer Care
1-800-237-7691
Monday – Friday: 8am – 10pm ET
Saturday: 9am – 8pm ET
Sunday: 10am – 7pm ET
Register your product today!
Registering is quick, easy and offers you benefits over the lifetime of your
product.
You’ll receive: BISSELL® Rewards Points Product Support Reminders
Automatically earn points for and Alerts
BISSELL® Rewards Points
Automatically earn points for discounts and free shipping on future purchases.
Faster Service
Supplying your information now saves you time should you need to contact us
with questions regarding your product.
Product Support Reminders and Alerts
We’ll contact you with any important product maintenance reminders and alerts.
Special Promotions
Optional: Register your email to receive notice of offers, contests, cleaning
tips, and more!
Visit www.BISSELL.com/registration!
Visit the BISSELL website: www.BISSELL.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number:
Please record your Purchase Date:
NOTE: Please keep your original sales receipt. It provides proof of purchase
date in the event of a warranty claim. See the Warranty page for details.
For cleaning tips and more visit www.BISSELL.com or find us at:
BISSELL BISSELLClean BISSELLClean BISSELL
BISSELL
We can’t wait to hear from you!
Rate this product and let us (and millions of your closest friends) know
what you think!
www.BISSELL.com
©2018 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 161-7524 10/18 RevC
Visit our website at www.BISSELL.com
Bissell 2513, 2694 Series Spotclean Little Green Vacuum User Guide – Download
[optimized]
Bissell 2513, 2694 Series Spotclean Little Green Vacuum User Guide –
Download
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>