SLINEX SQ-04 4 Inch Video Intercom User Manual

LINEX SQ-04 4 Inch Video Intercom

OVERVIEW

As a result of continuous upgrades and functionality improvements, the technical characteristics of the device can be changed without any preliminary declaration. This manual can contain some inaccuracy or misprint. The owner reserves the right to make corrections to the information described in the user manual and device package. The last revision of this manual is available on www.slinex.com

Safety instructions
Read and keep that manual.
The device installation process should be carried out by qualified specialists. Use the device from –10 ˚C to +55 ˚C, always keep it within that temperature range. The installation surface should be free from vibration and impact influence. Keep this device far from open sources of heat, such as radiators, heaters, and ovens. The device can be installed near other electronic equipment in case if the temperature of the environment does not exceed the previously mentioned range. The device should be protected from the direct influence of natural phenomena, such as direct sunlight, rain, or snow. Don’t use aggressive or abradant detergent for the device’s surface cleaning. Use a soft wet cloth or tissue to remove strong dirt. Don’t overpower outlets. It can cause fire or electric shock.
Nature protection
Don’t throw away the device with other industrial or nutritive trash if you see that symbol. Some regions have separation and recycling systems for electronic equipment. Connect with local authorities to receive information about the recycling of electronic equipment for your region.

Rights and limitation of liability
All rights reserved. Any part of that document can not be published in any form, translated into other languages, or reproduced in any way including electronic or mechanical. Document recording and copying is strictly denied without the owner’s permission.

 Package

• SQ-04 indoor monitor
•  1 pc. Wall mounting bracket
• 1 pc. Connection wires
• 1 pkg. Mounting screws and nuts
•  1 pkg. User manual
• 1 pc.

SPECIFICATION

• SCREEN                                  STANDBY MODE POWER CONSUMPTION
  4.3”, color TFT                        1 W

• RESOLUTION                      WORKING MODE POWER CONSUMPTION
  480×272 px.                          6 W

• VIDEO SYSTEM                POWER SUPPLY
  PAL / NTSC                        Built-in power supply, ~100–240 V

• AUDIO TYPE                    MOUNTING TYPE
  Half-duplex                          Surface mount

• CALL DURATION            DIMENSIONS
  120 seconds                        175×119×21 mm (6.89×4.68×0.83″)

• MEMORY                          WORKING TEMPERATURE
  No                                    10 … +55 °C (+14…+131 °F)

Description

• Display;

• Power switch;

• «Monitor» button – door panel or camera image monitoring;

• «Answer» button – incoming call answer and start talking with the visitor; «Unlock» button – door unlocking;

• «Hang Up» – stop conversation with the visitor;

• Microphone;

• Settings joystick :
  press the joystick while monitoring or talking to enter brightness/contrast/chroma settings. Change current parameter by pressing joystick again;
  move the joystick up or down to change the current parameter value;

• Ring volume tuning slider                      . Slide up to increase ring volume or down to decrease it;

• Talking volume tuning slider.                Slide up to increase talking volume or down to decrease it.

 Installation

Cable requirements
Disconnect all power cables before device installation.

The cable type that is used for device connection depends on the distance between the last indoor monitor in the system and the outdoor panel:

• Use a 4-wire cable with such parameters:
  • distance up to 25 meters (82 ft.) use a cable with 0,22 mm˛ square of one wire (AWG 24);
  • distance 25 to 50 (82-164 ft.) meters use a cable with 0,41 mm˛ square of one wire (AWG 21);
  • distance 50 to 100 meters (164-328 ft.) use a cable with 0,75 mm˛ square of one wire (AWG 18).

• If the distance between the door monitor and the door panel is between 80 and 100 meters (262-328 ft.) then use a 3-wire cable with 0,75 mm˛ (AWG 18) square of one wire and RG-59 or RG-6 coaxial cable for the video signal.

• Shielded or non-shielded twisted pair (not recommended):
  • distance up to 25 meters (82 ft.) non-shielded twisted pair can be used;

Schematic diagram
SQ-04 outdoor panels and locks connection.

Unit mount

•  Take the surface mount bracket from the kit and place it 150-160 cm (approx. 5 ft.) from the floor line.
•  Mark and drill four halls in the wall.
•  Take four wall anchors from the kit and hammer them into the drilled halls.
•  Fix surface mount bracket on the wall with four screws from the kit.
•  Connect all communication wires and fix the monitor on the surface mount bracket.

Operation

Incoming call

Notes:

• The monitor will be automatically switched into standby mode if the user doesn’t answer an incoming call during 60 seconds;
•  Image and sound from the door panel will be active for 20 seconds after the moment the user presses}
  button. It let the user know if the visitor passed through the door.

Outdoor panels image view

Notes:

If someone presses the call button on the door panel while monitoring is active then the image from this door panel appears on the monitor screen and the call melody starts. Press the «Answer» button to start a conversation.

Limited warranty

The manufacturer guarantees the product’s normal functioning during the warranty period if the user keeps all safety instructions described in that manual. The warranty period is 12 months from the moment of the product purchasing (warranty period could be extended up to 24 months or more, depending on the local regulations). The warranty period allows the user to make a guaranteed repair in cases when the normal functioning of the product was violated by the fault of the manufacturer and the user has not offended transporting, installation and working conditions. This limited warranty does not cover any damage to the product that results from improper installation, accident, abuse, misuse, natural disaster, insufficient or excessive electrical supply, abnormal mechanical or environmental conditions, or any unauthorized disassembly, repair or modification. Warranty void in such cases:

•  the product was damaged by the fault of the customer;
•  the product wasn’t properly installed according to reccomendations from the manual;
•  the sticker on the backside of the product was broken;
•  the product was not used for its intended function.

This limited warranty covers only repair, replacement, refund, or credit for defective products, as provided above. The manufacturer is not liable for and does not cover under warranty, any damages or losses of any kind whatsoever resulting from loss of, damage to, or corruption of, content or data or any costs associated with determining the source of system problems or removing, servicing or installing products. This warranty excludes third-party software, connected equipment, or stored data. The manufacturer is therefore not liable for any losses or damage attributable to third-party software, connected equipment, or stored data. In the event a product has been discontinued, the manufacturer shall either repair the product, offer to replace it with a comparable product, or provide a refund at the lesser of the purchase price or the product’s current value.
Repaired or replacement products will continue to be covered by this limited warranty for the remainder of the original warranty term.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>