Yi Zhao Q2 Pro Hybrid Active Noise Cancelling Earbuds User Guide
- June 6, 2024
- Yi Zhao
Table of Contents
Yi Zhao
Q2 Pro Hybrid Active Noise Cancelling Earbuds
User Guide Hybrid Active Noise Cancelling Earbuds
True Wireless Earphones
PRODUCT PARAMETERS
| Model name | SuperEQ Q2 Pro |
|---|---|
| Bluetooth version | 5. |
| Bluetooth range | 10m/33ft |
| Input | 5V |
| Over-voltage protection | YES |
| Speaker | 12mm Dynamic |
| Noise reduction | (FF+FB) x 2 |
| Acoustic code | SBC, AAC |
| Power display | IOS |
| Battery capacity | 55mAh x 2 (earbuds), 370mAh (charging case) |
| Playtime (varies by volume level and content) | 70% volume, ANC OFF: Up to 11 |
hours (Total 40 hours with the charging case)
70% volume, ANC ON: Up to 8 hours (Total 30 hours with the charging case)
PRODUCT DESCRIPTION
- Indicator light
- Type-C charging port
- Microphone
- Microphone
CHARGING
Fully charge both the earbuds and the charging case before the first use. The 3 LED indicators are lit when fully charged. Note: Please remove the insulating film on the earbuds when using it for the first time, otherwise it will not be able to charge.
WEARING
Choose the ear tips that fit your ears best
Install the ear tips on the earbuds Install the ear tips
Insert the earbuds into the inner canal of your ears and turn gently until you
find the most comfortable and secure position 4
LED DISPLAY
1. The two earbuds have been paired with each other (normal): the main earbud
flashes alternately blue and white and the second earbud flashes white every 5
seconds.
2. The two earbuds lose their pairing: The two earbuds flash alternately blue
and white.
POWERING ON/OFF
ON Open the charging case, the earbuds will automatically power on.
To power off, and close it. place the earbuds in the charging case
BLUETOOTH PAIRING
CONTROLS
CONTROLS Normal/Transparency/ANC ON………………………………… Long Press(L/R)
| Voice assistant | Press 3 times(L/R) |
|---|---|
| Play / Pause | Press once (L/R) |
| Previous track | Press twice (L) |
| Next track | Press twice (R) |
| Answer a call | Press once (L/R) |
| End a call | Press once (L/R) |
| Reject a call | Long Press(L/R) |
CONTROLS
Normal Mode
It’s the normal mode when you turn on the earbuds at the first time, and it
will turn off if you do not connect it to any Bluetooth device in 3 minutes.
ANC Mode
Reduce the low-frequency ambient noises, press and hold(L/R) to start the
ANC mode.
Transparency Mode
Chat with people without taking off your earbuds, press and hold (L/R) to
start the Transparency mode.
Voice Assistant Press 3 times(L/R)to Activate Siri or other voice
assistant software.
IMPORTANT
Please try to reset the SuperEQ Q2 Pro and restore the factory default if
you face any difficulties:
Place both 2 earbuds into the charging case. Quickly tap 5 times in both ears
at the same frequency. The blue LED flashes and resets successfully.
If the right and left earbuds disconnect with each other
Please click the left earbud three times to send the pairing instruction to
the right earbud, and the pairing will be successful again.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:(1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
FCC ID:2A25A-Q2P52
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>