FLASH F7300247 LED Derby Laser RG+LED User Manual
- June 6, 2024
- FLASH
Table of Contents
FLASH F7300247 LED Derby Laser RG+LED User Manual
1. INTRODUCTION
THANK YOU FOR PURCHASING LED DERBY LASER RG + LED. FOR SAFETY REASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CAREFULLY READ THE INSTRUCTIONS.
2. SAFETY INFORMATION
Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.
- Unpack and check carefully there is no transportation damage before using the fixture.
- Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture.
- t’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
- Disconnect main power before servicing and maintenance.
- Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
- Do not use the device in high humidity conditions. Use in 20°C to +35°C
- In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
- Do not connect the device to any dimmer pack.
- Do not touch any wire during operation and there might be a hazard of electric shock.
- To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
- The housing must be replaced if they are visibly damaged.
- Do not look directly at the LED light spot while the fixture is on.
WARNING! The device must be connected to the power supply in order to avoid condensation.
IMPORTANT!
Do not point strong light output from other fixtures
at the LED DERBY LASER RG + LED, as intense illumination can damaged the
display.
Figure 2. Lenses can focused sunlight and strong light, presenting a risk of
fire and damage to the fixture.
Shield or shade the head if necessary.
3. PRODUCT INFORMATION
- Power supply voltage: 110-240V (50/60Hz)
- Power consumption: 30W
- Number of diodes: 9
- Color: RGB
- Beam angle (min/max): 6
- DMX standard: DMX 512
- Control interface: 4 buttons
- Operating modes: Operation: Auto, DMX512,Sound, Master/Slave
- Additional information: Laser Effect: Red 120mW & Green 30mW
- DMX IN/OUT: XLR – 3 pin
- IP Rating: IP20
- Housing made: Steel
- Dimensions: 18,5×16,2×21 cm
- Weight: 1,48 kg
- Type of packaging: Carton Box
4. INSTALLATION
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.
5. CONNECTION
The device is equipped with the following interfaces:
- DMX (in/out): XLR 3(5)-pin socket
- Power (in/out): powerCON socket
5.1 Connecting DMX signal
The connection is performed using cable with XLR-female -> XLR-Male plugs.
CAUTION! At the last fixture, the DMX signal has to be terminated with a
terminator. Solder a 120Ω resistor between signal (-) and signal (+) into a
XLR plug and plug it in the DMX output of the last fixture.
User Manual
5.2 Voltage specification
| Input Voltage | Total Power | Frequency |
|---|---|---|
| 220/240V | 40W | 50/60Hz |
5.3 Connecting power supply
The connection is performed using power cable with PowerCon connector
(included). The device must be operated by qualified personnel
Make sure that the power grid supply parameters are consistent with device
parameters and limitations are not exceeded.
CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions
5.4 LED Display function
Operation
- When power is on, the digital LED display works with red dots. When a DMX signal is present, the dot will be shiny.
- DMX address code setting: Press „MENU” button. When the digit LED displays d001-d512, press „UP” or „Down” to set the addrress code. The code ranges from 001-512.
Button Specyfications:
| | All Effects| | Motor Speed| |
---|---|---|---|---|---|---
Autn| ®| An01-An07| ®| S.01-S.09| ®|
| | Derby effects| | Motor Speed| |
Autp| ®| Ap01-AP07| ®| S.01-S.09| |
| | Laser effects| | Motor Speed| |
AutF| ®| AF01-AF04| ®| S.01-S.09| |
| | Sound effect Whole Unit| | Sound Effect – Derby| |
Sound Effect Laser
Sound| ®| S.01-S.03| ®| S0.4| ®| S.05
SLAU| ®| Slave| | | |
D001-d512| ®| DMX| | | |
5.5 DMX 8CH
| CH no. | Value | Description |
|---|
CH1
| 0-9| /
10-19| Effect of the Whole Unit (An01-7)
20-29
30-39
40-49
50-59
60-69
70-79
80-89| Derby Effects (Ap01-AP07)
90-99
100-109
110-119
120-129
130-139
140-149
150-159| Laser Effect
160-169| (AF01-AF04)
170-179
180-189
190-199| Sound Effect (Whole Unit) (S.01-S.03)
200-209
210-219
220-229| S.04 Sound Effect (Derby)
230-255| S.05 Sound Effect (Laser)
CH2| 0-9| /
10-255| Speed adjustable
CH3| 0-255| Derby (Red, Blue, Warm White)
CH4| 0-255| Derby (Orange, White, Yellow)
CH5| 0-255| Derby (Green, Purple, UV)
CH6| 0-255| Motor Speed
CH7
| 0-63| /
64-127| Red Laser
128-191| Green Laser
192-255| RG Laser
CH8| 0-255| Laser Motos Speed
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>