Fontastic 260803 PISA Two-In-One TWS Speaker User Manual
- June 6, 2024
- fontastic
Table of Contents
EXCLUSIVE
Two-In-One TWS Speaker
PISA
User Manual
Thank you for purchasing the Pisa wireless speaker.
Pisa consists of 2 TWS speaker units that can be placed together or
separately, as desired, and will provide perfect surround sound. The
exceptionally balanced sound of the Pisa, combined with a deep bass
distinguishes the Fantastic speaker. Have fun using your Fontastic Pisa
speaker.
Please read the user manual carefully and follow the safety instructions.
Package contents:
- Speaker Pisa
- Dual Micro-USB charging cable
- Instruction manual
Overview:
- Microphone
- Micro USB port
- On/off button / multifunction button
- Status LED
Getting started Charging the battery
Both Pisa units are equipped with an internal rechargeable Lithium-Ion
battery. Connect the Dual Micro-USB cable, which is included, to the Micro USB
charging port of both Pisa units. Connect the USB-A connector to a USB
charger. Any standard USB charger can be used, although we recommend chargers
with 5V/2A or more than 2A. The speaker’s status LED will glow red during
charging. When fully charged, the LED will turn off. The cable can now be
disconnected from the speaker and the charger. Fully charge both units before
using them for the first time.
Note: A low battery level is indicated by an acoustic signal. Please
charge the speakers.
Note: To save power, the speaker will turn off after 10 minutes if there
is no connection.
Switching on/off
To turn on the speaker, press and hold the ON/OFF button for about three
seconds. The device switches on. The status LED flashes blue, the device is in
pairing mode.
To turn off the speaker, press and hold the ON/OFF button for about three
seconds. The device and the status LED switch off.
TWS function
Pisa consists of 2 separate speaker units. To enjoy full stereo music
streaming, it is recommended to connect both Pisa units together (TWS).
Set up TWS connection The TWS function allows you to connect both Pisa units
together. To connect the two units, turn on both Pisa speakers at the same
time. The blue LED of both units will start blinking and the units will
connect automatically. After both units are connected (approx. 4-6 seconds), a
signal will sound and the LED of the TWS speakers will light up permanently.
Pairing with a Bluetooth® source
Pisa must be paired with a Bluetooth device before it can be used. After a
successful TWS connection, pairing with a Bluetooth device can take place.
- Activate the Bluetooth® search function in your music source (e.g. smartphone).
- The searching Bluetooth® device indicates that it has found the speaker „Pisa”.
- Confirm the pairing with „Pisa”. Enter „0000″ if you are asked for a pairing code. A successful connection is indicated by an acoustic signal and the constant glow of the blue LED.
When using a Bluetooth device without a display, switch it to pairing mode and wait a few seconds for the connection with the speaker to be established.
Note: If the connection is lost or the transmitter is disconnected for a short time, Pisa will automatically try to reconnect. If the connection cannot be restored after 3 seconds, restart the pairing process.
Music playback
Play music via Bluetooth. Start music playback on the Bluetooth® source paired with the Pisa. The music is transmitted to the Pisa speaker. Stop the music playback of the Bluetooths source to interrupt the music streaming.
Music control
To play or stop music, briefly press the multifunction button.
Volume adjustment
The volume must be adjusted via the audio source.
Hands-free function
The built-in microphone and intelligent noise cancellation make the speaker
suitable to be used as a hands-free speaker for phone calls.
Note: High volume may cause feedback with the microphone. This will cause
echo on the phone side, not on the speakerphone side.
Accepting/ending/rejecting calls
To answer an incoming call, briefly press the multifunction button on one of
the speakers once. To end an ongoing call, briefly press the multifunction
button on one of the speakers once. To reject incoming calls, press the
multifunction button twice briefly. To transfer an ongoing call to the
smartphone, briefly press the multifunction button twice. Repeat the process
to return the call to the speaker.
Separating/assembling loudspeaker units
To separate the units, take the device in both hands and turn the units
against each other. To put them back together, proceed in reverse.
Safety information:
- Never open the device.
- Do not submerge the device in water and keep it away from moisture.
- Never forcibly connect a cable.
- Place the device only on flat surfaces.
- Remove electronic devices from the power supply if they will not be used for a length of time.
- Do not use the device if it exhibits visible damage.
Technical Specification:
- BT: 5.0
- True Wireless Stereo (TWS)
- Transmission range: 10m
- Speaker per unit: 53 mm diameter, 10 watts, 40
- S/N ratio: 70dB
- Charging voltage: 5V/0.8A
- Protection class: IPX6 (splash-proof and suitable for outdoor use)
- Battery capacity: 2 x 1500mAh
- Internal microphone
- Operating time: 12-13 hours
- Charging time: 2-3 hours
- Total dimensions: 204 x 74.5 x 74.5mm
- Total weight: 792g ± 10
No liability is accepted for any damage which may occur through the improper
operation.
If you require technical support, please contact our support team via email at
[email protected].
Registration and Safety Certification/General Information
We hereby declare that this device carries the CE mark in accordance with the
regulations and standards. It conforms with the fundamental requirements of
the RED 2014/53/EU, as well as the RoHS directive 2011/65/EU. The full text of
the EU declaration of conformity is available at the following internet
address: www.d-parts.de/Konfo
Note on environmental protection:
****After the implementation of the European Directive 2012/19/EC in the
national legal system, the following applies: Electrical and electronic
devices may not be disposed of with domestic waste. Consumers are obliged by
law to return electrical and electronic devices at the end of their service
lives to the public collecting points set up for this purpose or point of
sale. Details of this are defined by the national law of the respective
country. This symbol on the product, the instruction manual, or the package
indicates that a product is subject to these regulations. By recycling,
reusing the materials, or other forms of utilizing old devices, you are making
an important contribution to protecting our environment.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.
and any use of such marks is under license.
Improvement and changes of the technical specifications and other data’s could
be made without prior notice.
Registered trademarks are the property of their respective owners.
Fontastic, by D-Parts GmbH
Birkenweiher Str. 16 • 63505 Langenselbold, Germany