PROZIS Satin Women’s Grooming Kit User Manual

Satin
Women’s Grooming Kit

User Manual Warranty Statement
V.1
09/2021

Prozis is a registered trademark of PROZIS.COM, S.A.

Prozis reserves the right to adjust or modify the product or any of the associated documenta­tion in order to ensure its suitability for use, at any time and without prior notice.

NOTE: The most recent version of this product’s user manual can be found at www.prozis.com/user-manuals

Legal compliance statement

By means of this document, PROZIS declares that the Prozis Satin – Women’s Grooming kit- is fully compliant with all the standards specified in the applicable legislation as well as other relevant clauses.

Prozis will always be available for any additional explanation through our customer support communication channels, available at www.prozis.com/support

To avoid any impact on the environment or human health due to dangerous substances present in electrical and electronic devices, the end-users of such devices are expected to understand the meaning of the symbol consisting of a crossed-out waste container. Do not dispose of electrical and electronic equipment along with the unsorted household waste. Dispose of it separately and properly instead.

Used batteries should not be disposed of along with the household waste. They must be placed in a special container for used batteries. This is an obligation intended to ensure the ecological disposal of batteries. Dispose of them only when they are empty.

The packaging that protects the device against transport damage is made from non-polluting materials that can be disposed of via local recycling bins.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving
• Increase the separation between the equipment and
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
• Consult the dealer or an experienced radio/ TV technician for

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Safety warnings

DANGER! This symbol, when combined with the note Danger, means high risk. Failure to observe this warning may lead to injury to life and limb.

DANGER FOR CHILDREN AND PEOPLE WITH DISABILITIES

• Packing materials are not Children must not play with the packing materials. There is a suffocation risk.
• This product may be used by children 8 years and up as well as persons with physical, sensory, or mental impairments or lacking experience and knowledge, when supervised or instructed in the safe use of the product and understanding the associated
• Children must not play with the
• Cleaning and maintenance must not be performed by children without
• Keep the device out of the reach of

DANGER! KEEP THE APPLIANCE DRY.

• Never submerge the appliance in water or other
• Do not use the appliance while taking a bath. Risk of fatal electric shock!
• Check the appliance for visible external damage before use. Do not use an appliance that is There is a risk of fatal electric shock.
• Do not use this appliance if the foil and blade are broken or damaged, as injury may
• Before using the appliance, make sure the cutting head is securely fitted.
• Always check blade alignment before Do not touch the blades as they are very sharp.
• The appliance can become hot during use Use it for a maximum of 30 minutes, and then allow it to cool down for 30 minutes.
• The appliance is only intended for clipping and shaving humans Do not use this appli­ance for any other purposes.

CAUTION! This symbol highlights dangerous situations that can lead to minor to moderate injuries, damage, malfunction, and/or destruction of the device.

To prevent harm or damage from happening to users or others, make sure to comply with the following requirements.

Women whose skin is sensitive to cosmetics or easily irritated by shaving, or who suffer from skin allergies, should test one area of the leg or arm before using the shaver head.

Do not use the appliance if:

• You have a sunburn.
• You have skin irritation or redness.
• You have a skin condition such as neurodermatitis.
• You have pimples, moles or
• You have wounds, open sores, or raised scars.

Suitable for cleaning underwater! Use cold water to clean the device. Do not use hot water or any cleaning agents, as these can cause damage to the waterproof seals.

CAUTION, HANDLING BATTERIES.

• Observe the plus (+) and minus (-) polarity symbols.
• If your skin or eyes come into contact with battery fluid, rinse the affected area with water and seek medical assistance.
• Choking hazard! Small children may swallow and choke on batteries. Store batteries out of the reach of small children.
• If a battery has leaked, put on protective gloves and clean the battery compartment with a dry cloth.
• Protect batteries from excessive heat.
• Risk of explosion! Do not throw batteries into a fire.
• Do not charge or short-circuit batteries.
• If the device is not going to be used for a long period of time, remove the batteries from the battery compartment.
• Never open, solder, or weld batteries. There is a risk of explosion and injury!

User manual

PACKAGE CONTENTS

• 1 x Prozis Satin – Women’s Grooming Kit
• 1 x Eyebrow Trimmer Head
• 1 x Bikini Trimmer Head
• 1 x Facial Brush Head
• 1 x Cleaning Accessory
• 1 x Carrying Bag
• 1 x Quick Guide

PRODUCT OVERVIEW (SEE PAGE 2)

1. Shaver’s head
2. “0” marking
3. Bottom housing

Maintenance and cleaning

Cleaning:

• Switch the product off and remove the battery before cleaning!

• Do not use aggressive or abrasive cleaning agents or materials such as scouring milk or steel wool. They can damage the upper surface of the appliance!

• Protect the device from water drops and water spray.

• Only use a clean, dry cloth for cleaning the appliance and never use any corrosive liquids. Use a slightly damp cloth and a mild cleaning agent to remove any stubborn dirt.

• Only use cold water. Do not use hot water, as it can damage the waterproof seals.

• Make sure moisture does not enter the product while cleaning to prevent damage to the product and related repairs.

• To clean the shaving head, remove it by rotating the top of the “0” head to the right, and aligning the arrows.

• To remove the shaver cap, rotate the top of the head to the left and align the arrows.

• Wash the shaver and the foil frame under running water or in a sink. Do not use hot water. Use only cold water.

• After cleaning, allow the foil frame and the cutters to air dry before closing the foil frame and the shaver head. Replace the shaver head on the main unit – it will click into place. Clean the surface of the main unit with a dry towel.

Monthly deep deaning:

1. Remove the inner cutter lock away from the cutters.
2. Remove the cutters.
3. Carefully wash off any residue.
4. Replace the inner cutters by matching them with the corresponding outer cutter
5. Place the inner cutter lock back into position by sliding it back into the holder until it clicks into place.
6. Mount the cutter head back onto the main unit.

How to dean your trimmer head:

Since the trimmer blades are specifically made for very special use, they should always be handled with care. Each time you finish using the trimmer, remove the supplied cleaning brush and brush off any loose hair left on the blades. Afterward, rinse them with water only, allow them to air dry, and store the trimmer until you need to use it again.

When shaking off any excess water, hold the main unit firmly to avoid releasing the head assembly or dropping the unit.

Do not use a dryer or a heater to dry the trimmer. This may result in malfunction or damage to the trimmer.

How to clean your facial brush head:
Separate the brush head from the brush holder. Clean with warm soapy water. Dry the brush with a towel.

Storage:

• Store the product in a dry environment, protected from dust and direct sunlight.
• If the appliance is not going to be used for a long period of time, you should remove the battery to prevent leakage.
• Store your appliance inside the original case provided.

INSTRUCTIONS

How to use

Battery installation:

1. Twist the bottom housing to the left, align the   triangles and pull.
2. Insert the battery (not included).
3. Slide the bottom housing back into place and align the O.
4. Make sure the battery is installed correctly, according to the polarity symbols (+ and -).
5. Remove the battery when depleted or if the trimmer has not been used for a long period of time.
6. Clean the battery contacts and also those on the device prior to installing the battery.
7. Promptly remove the depleted battery.
8. Always purchase the correct battery, which will be the one suitable for the device.

Trimmer Head Replacement:

1. Make sure the unit is switched off.
2. Twist the head counterclockwise and align the triangles.
3. Switch the head attachment, turn the head clockwise and align the triangle with the “O” marking.

How to use:

The unit will start working once the “I” and the triangle markings are aligned. After use, switch off the device by rotating the bottom housing, aligning the triangle with the “O” marking.

Shaving:

1. Attach the shaver head.
2. Twist the bottom housing to the right and align the “I” and the triangle markings to start the unit.
3. Hold the shaving foil against the skin, moving the shaver slowly and smoothly in circular motions against your natural hair growth.
4. Don’t press the device too hard against the skin as this will cause irritation and may damage the foil.
5. Since your skin may be sensitive after shaving, test your moisturizer on a small patch of skin and wait to see if any irritation occurs.
6. Clean the shaver after each use to ensure long-lasting performance.
7.  Twist the bottom housing to the left and align the “O” with the triangle marking to switch off the unit.

Using the bikini trimmer:

1. This trimmer comes with two trimming blades. The larger blade can be used to trim body hair and eyebrows. The smaller blade is ideal for detailing. It also comes with a comb attachment that helps you achieve an even cut when you do not want to fully remove the hair. The comb attachment has two sides: the long tooth is for body hair, and the short tooth is for eyebrow trimming.
2. Aligning the indicator with the 6 mm marking on the comb leaves hair longer while aligning it with the 3 mm marking leaves the hair shorter.
3. To use the comb attachment, make sure the unit is switched OFF and slide the comb over the trimming blades. Make sure the comb’s teeth are facing in the same direction as the trimming blade, and that the top of the comb is even with the top of the trimmer. If you want to fully remove hair, use the trimmer without the comb attachment.
4. To operate the trimmer, twist the bottom housing to the right, pointing the arrow towards the “I” marking. After trimming, switch off the device by twisting the bottom housing to the left, pointing the arrow to the “O” marking.
5. To store the trimmer, slide the comb attachment cover over the trimming blades.

Using the facial brush head:

1. Make sure the unit is switched off.
2. Twist the head to the right aligning the triangles.
3. Change the accessory and fit a new one, then twist it to the left and align the “0” with the triangle marking.
4. Add a drop of facial cleanser to the head of the brush and moisten it under the tap or shower.
5. Twist the bottom housing to the right and align the “I” and the triangle markings to start the unit.
6. Divide your face into 4 main sections for deep cleansing: forehead, nose and chin, left cheek, and right cheek.
7. While applying gentle pressure, move the roller brush in circular motions over each section for approximately 30 seconds.

Troubleshooting

Some issues that arise may be solved by the user. If the problem persists after having tried the following solutions, please contact Prozis customer service.

the battery is properly placed in the battery compartment. Test the battery to make sure it is working / Check the blades to see if they are clogged with any hair residue. If so, use the cleaning brush to remove it.

Warranty statement

All electrical and electronic products commercialized by Prozis via www.prozis.com are cov­ered by the warranty applicable to the purchase and sale of consumer goods.

GENERAL CONSIDERATIONS
This document contains the terms and conditions of Prozis’ warranty for final consumers.

This warranty is valid exclusively for consumers who purchase the product for non-profession­al purposes.

WARRANTY PERIOD
Prozis guarantees the product is to remain free from material and production defects for a 2-year period, counting from the date of initial purchase by a consumer and respective deliv­ery, or for longer if legally established by the applicable national law.

In the event that repair is required, this 2-year period is suspended during repair time.

CONSUMABLES
The gradual performance decrease caused by prolonged use of the product’s consumable components, such as batteries, is not covered by this warranty unless the malfunction is caused by faulty design, materials or production.

HOW TO MAKE A CLAIM
If the need arises to exercise the rights conceded to you through this warranty, please contact Prozis customer service via the communication channels provided on the Prozis website,

and follow the provided instructions or recommendations. Contact and technical assistance information is also provided at the end of this warranty.

Any claims made regarding this warranty will only be valid if proof of purchase is presented by the original customer. This proof of purchase may be the original invoice or receipt, as long as it includes information regarding the date of purchase and the product’s model name.

WARRANTY REPAIRS
Any repairs made under this warranty cannot be made by third parties. This warranty does not apply to any repairs, or damage caused directly by such repairs, that have impacted or caused the damage that is the subject of the respective warranty claim.

EXCLUSIONS
The following situations are not covered by this warranty:

1. Any wear and tear of parts and components resulting from normal product use.
2. Cracks, dents, scratches, and other types of surface damage that only affect the prod­uct’s appearance.
3. Any malfunction caused by inappropriate use of the product that does not comply with user manual instructions.
4. Use and storage of the product not complying with user manual instructions.
5. Opening of the product by a third party who is not authorized to proceed to its repair.
6. Altering or changing parts or components, whether internal or external.
7. Damage caused by battery leakage resulting from the breaking of any of its components, or from product misuse.
8. Malfunction or damage due to reasons that cannot be ascribed to the production or design of the product.
9. Use of the product in the context of a business, occupation, or commerce.
10. Malfunction due to use that does not comply with the technical or security norms in force, or with user manual instructions.

The services provided by Prozis in order to repair or fix any fault or malfunction resulting from the verification of any of the aforementioned excluded situations will be subject to payment of labor, transport, and component costs.

The customer shall bear all risks of loss and damage to the product during transportation to Prozis. This warranty will be void if the returned product arrives with labels or stickers that have been removed, damaged, tampered with or modified in any way.

LIMITED RESPONSIBILITY

Prozis cannot be held responsible for indirect damage or loss due to usage of the product.

WHAT TO DO?
To request warranty service, you must first contact Prozis customer service via the commu­nication channels provided on the Prozis website, and follow the provided instructions and recommendations.

Send back the product inside its original packaging, including all accessories and documen­tation, to the following address:

PROZIS
Rua do Cais n° 198
4830-345 Povcia de Lanhoso Braga – Portugal

CONTACTS
Prozis is always available for additional clarification through their customer service communi­cation channel at www.prozis.com/support

Zona Franca Industrial
Plat 28 – Pavilhão K – Mod 6
9200-047 Caniçal, Madeira

References

• Prozis – Official Store | Exceed Yourself!
• Prozis – Official Store | Exceed Yourself!
• Customer Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>