AIYATO 725550-420539 Locator User Guide
- June 12, 2024
- AIYATO
Table of Contents
Works with Apple Find My
AIYATO Locator Quick Start Guide
Getting Started
-
Power On/ Off:
• Press the AIYATO Locator Function Button once to turn it on. It should a ringing chime to indicate that it is powered on.
• To power off, hold the same button for at least three seconds. You will hear two beeps to indicate that your AIYATO Locator is powered off. -
Check For Updates:
Add Your “AIYATO Locator “
-
Start the App
• Open Find My app on your supported iPhone* or iPad®
• Allow notifications from the app -
Connect your AIYATO Locator
• Power on your AIYATO Locator
• Tap H“+” then “Add Other Item”
• Once your AIYATO Locator is located, tap “Connect”
• Choose a recognizable name and emoji for your Item Locator and tap “Continue”
• Find My will ask for confirmation to add your AIYATO Locator to your Apple ID – tap “Continue”
• Lap “Finish” and your AIYATO Locator will be set up and ready to be connected to whatever item you wish to locate, e.g., your keys
Find Item When Out of Range
-
Enabling “Notify When Left Behind”
• Open Find My app and select the “Items” tab or open the Find Items app on your Apple Watch
• Tap on your AIYATO Locator from the list
• Under “Notifications”, enable the “Notify When Left Behind” toggle
• You will receive a notification when you leave your AIYATO Locator behind and it’s no longer in range of your device. -
Enabling “Notify When Found”
• Under “Notifications”, enable the “Notify When Found” toggle
• When your AIYATO Locator is seen by another Find My enable d device, you will receive a notification of its updated location
• Note: “Notify When Found” can only be activated when your AIYATO Locator is out of range
How to deal with device loss
- Enabling unlost Mode
• Open Find My app and select the “Items” tab or open the Find Items app on your Apple Watch
• Lap on your AIYATO Locator from the list
• Under “Lost Mode”, tap “Enable”
• A screen detailing Lost Mode will pop up, tap “Continue”
• Enter your phone number or email address and tap “Next”
• You may enter a message that will be shared with the person that finds your item
• Tap “Activate” to enable “Lost Mode”
• Note: When “Lost Mode” is enabled, “Notify When Found” is automatically enabled
• Note: When “Lost Mode” is enabled, your AIYATO Locator is l docked and cannot be paired to a new device
Resetting Your AIYATO Locator
-
Remove the AIYATO Locator from Find My™ app
• Open Find My app and select the “Items” tab
• Tap on your AIYATO Locator from the list
• Please ensure “Lost Mode” is disabled
• Scroll to the bottom of the screen and tap “Remove Item”
• A summary will open, tap “Remove” to confirm -
Factory Reset Your AIYATO Locator:
• After successfully removing the AIYATO Locator from Find My ™ app, press the AIYATO Locator’s function button four times rapidly and t hen hold it a fifth time until you hear a ringing chime.
• The AIYATO Locator is now reset and ready to be paired to a new Apple ID.
AIYATO Locator Product Specification
| 1. PPID No | 725550-420539 |
|---|---|
| 2. Product Size | 47 x 28.5 x 6.0 mm /1.85 x 1.12 x 0.23 inch |
| 3. Product Weight | 8 g / 0.282 oz. |
| 4. Battery | Built in battery |
| 5. Voltage | DC 3V |
| 6.Current | ≤5uA(Standby) / ≤10mA(Max) |
| 7. Wireless | BLE 5.2 |
| 8.Wireless range | ≥40m（Line-of-sight） |
| 9. Buzzer | Built-in ≥75db (in 10cm) |
| 10. Temperature | －5°C — 45°C (23°F — 113°F) |
| 11. Humidity Range | ≤95%（Non-condensing） |
| 12.Color Box Size | 50mm x 18.5mm x 84mm |
| 13. Product Cortication | FCC / Rohus / UU CE |
But Wait… There’s More
-
Replace the Battery:
• Use your fingernails at the small gap on the side of your AIYATO Locator to carefully open the case
• Replace the battery with a new CR2032 battery placing it positive side up (text facing up)
• Carefully align the top hole on both sides to close -
Unwanted Tracking Detection:
• If any Find My network accessory separated from its owner is seen moving with you over time, you’ll be notified in one of two ways:
(1) If you have an iPhone, iPad, or Find My will send a notification to your Apple device.
This feature is available on iOS iPod touch, or iPadOS 14.5 or later.
(2) If you don’t have an iOS device or smartphone, the owner’s locator will automatically make a sound after a period of time. These features were created specifically to discourage people with its owner for a pend of time will emit a from trying to track you without your knowledge.
The Fine Print
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harm full interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
The Fine Print
(1)This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 0cm between the radiator and your
body.
Use of the Works with Apple badge means that a product has been designed to
work specifically with the technology identified in the badge and has been
certified by the product manufacturer to meet Apple Find My network product
specifications and requirements.
Apple is not responsible for the operation of this device or use of this
product or its compliance with safety and regulatory standards. ©Apple, Apple
Watch, watches’, iPad, iPadOS, iPod touch, Mac, and macOS are trademarks of
Apple Inc., registered in the U.S. and other countries. 10S is a trademark or
registered trademark of Cisco in the U.S. and other countries and is used
under license.
Regulatory safety information：
Put the battery out of the reach of children. Due to chemical burn and
potential esophageal perforation, swallowing may cause serious injury or death
in just 2 hours. The causes are chemical burn and potential perforation of the
esophagus. If you suspect your child has swallowed or inserted a button cell,
please call the 24-hour Poison Information Center immediately for quick expert
advice.
Battery warning：
This device uses a CR2032 button battery. Rated voltage 3V, rated current
210-240 mAh If the following guidelines are not followed, the lifespan of the
lithium-ion battery in the device may be shortened or damaged. Do not
recharge, disassemble, heat (-20 ℃+70 ℃), or burn it. The risk of equipment,
fire, chemical burns, electrolyte leakage, and/or injury. Do not disassemble,
hole or damage the device or battery. Do not expose the battery to flames,
explosions, or other hazards. Do not use sharp objects to remove the battery.
EU Disposal Information:
The above symbol indicates that according to local laws and regulations, your
product and/or its battery should be disposed of separately from household
waste. At the end of the product’s service life, take it to the designated
collection point authority in the local area. Disposal time will help protect
natural resources and ensure that they are recycled in some way to protect
human health and the environment.
Made in China
Account ID: 312215
Manufacturer: Dong Guan Kenway Photoelectric Technology Co.,Ltd.
Address: 2/F, Building E1 , Qiangrongdong Industrial area, Zhoushan Road No.
723 ,
XiXiang, BaoAn, ShenZhen, China
Address: Room 418, Building 6, No. 36 Foxing Road, Chang’an Town, Dongguan
City,
Guangdong Province