ATEN PE0118S 1U Basic PDU with Surge Protection User Guide

PE0118S 1U Basic PDU
with Surge Protection
User Guide

ATEN NRGence™
PE0112, PE0212, PE0110S, PE0209S, PE0210S, PE0118S, PE0218S, PE0116S, PE0216S, PE0224S, PE0316S, PE0324S, PE0316B, PE0324B

Package Contents

1 power distribution unit
1 power cord (inapplicable to PE0316S,
PE0324S, PE0316B, and PE0324B)
1 L-shaped mounting kit (inapplicable to
PE0112, PE0212, PE0110S, PE0209S,
PE0210S, PE0118S, and PE0218S)
1 user instructions

Hardware Review

Mounting

1U Mounting (PE0112, PE0212, PE0110S, PE0209S, PE0210S, PE0118S, PE0218S)

1. Align the unit in 1U of space on the rack. Lift one end of the unit such that you can slide the unit where its rack mounts ears appear on either side of the rack poles. Refer to diagram “a”.
2. Stabilize the rack mount ears of the unit to the rack using screws. Refer to diagram “b”.

0U Mounting (PE0116S, PE0216S, PE0224S, PE0316S, PE0324S, PE0316B, PE0324B)

Using Rack Mount Ears

1. Align one of the screw holes of the ear to the rack’s screw holes and screw a screw to stabilize the unit to the rack. Refer to diagram “c”.
2. Repeat for the other rack mount ear to complete the rack mount.

Using Rack Mount Buttons

1. Identify where the buttonholes are on the rack, position the unit near the rack vertically and align the rack mount buttons to the buttonholes.
2. Insert the buttons into the buttonholes. Refer to diagram “d” (only the upper button configuration is shown in the diagram).
3. Let the buttons stabilize in the buttonholes, and the mounting is complete.

Using L-Shaped Mounting Kit

1. On the rear of the unit, unscrew the screw of the rack mount buttons and the screw below it. Refer to diagram “e”.
2. Position the unit near the rack vertically and align the 2 screw holes of the L-shaped mounting kit (as shown in diagram “f”) to the 2 screw holes of the unit. Stabilize the mounting kit to the unit using the screws from the kit.
3. Align one of the sliding holes (you can choose either) of the other half of the L-shaped mounting kit to a screw hole of the rack. Stabilize the mounting kit onto the rack using a rack screw.
4. Repeat for the other side (where the other rack mount button is) of the unit.

Hardware Installation

Note: For safety reasons, the equipment should be installed near the wall socket outlet and the disconnected device (appliance coupler on detachable power supply cord or plug on non-detachable power supply cord) should be readily accessible.

Refer to the installation diagram (the numbers in the diagram correspond to the numbered steps), and do the following:

1. Connect the unit power cord to an AC power source.
2. For each device, you want to connect, connect its power cable between the device’s AC socket (where applicable) and any available outlet on the unit.
   Note: We strongly advise that you do not plug the unit into a multi- socket extension cord, since it may not receive enough amperage to operate correctly.  Once you have finished these installation steps, you can turn on the unit and the connected devices.

Surge Protection Indicator (For PE0110S, PE0209S, PE0210S, PE0118S, PE0218S, PE0116S, PE0216S, PE0224S, PE0316S, PE0324S)
The Surge Protection Indicator is as shown in the Hardware Review.
It should normally be lit when the unit is powered.
If the indicator is not lit when the unit is powered, please power down the unit and any connected device safely. Return the unit to the dealer closest to your location for further assistance.

Support and Documentation Notice
All information, documentation, firmware, software utilities, and specifications contained in this package are subject to change without prior notification by the manufacturer. To reduce the environmental impact of our products, ATEN documentation and software can be found online at http://www.aten.com/download/

Technical Support
www.aten.com/support
Scan for more information

17802161

|

17802161  

© Copyright 2021 ATEN® International Co., Ltd.
ATEN and the ATEN logo are trademarks of ATEN International Co., Ltd. All rights reserved. All other trademarks are the property of their respective owners.
Part No. PAPE-1223-M61G Released: 03/2021

References

• ATEN - Simply Better Connections | ATEN U.S.A.
• Downloads | ATEN Corporate Headquarters

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>