ZOSI 8EN-2615W8-20-US 8CH 5MP PoE Home Security Cameras System User Guide
- June 6, 2024
- ZOSI
Table of Contents
ZOSI 8EN-2615W8-20-US 8CH 5MP PoE Home Security Cameras System
For more information of your new system, please refer to www.zositech.com
Introduction of System
PoE NVR
PoE Camera
A. Adjust to the desired position.
B. The neck of the bracket is connected to the mounting base. Rotate the
bracket by loosening the radial joint locking ring.
Adjust the position to the appropriate position and tighten the locking ring.
Connect the System
- Connect the camera to the NVR using a network ethernet.
- Connect the NVR to the router using a network ethernet. Connect the camera to a power source.
- Connect the monitor to the NVR via HDMI or VGA port.
- Plug the Mouse to the USB port at the back panel
- Connect the NVR to a power source.
- After the system starting, the display will show the real-time monitoring image of the camera.
Note: The picture shown is for your reference only. Please adhere to the actual product instead.
View on App
Connect the NVR to the Internet
A:How to connect NVR to the LAN?
B:How to test the network status of the NVR?
- Rlght dick Mouse> Go to Main Menu> Setup> Network
- Tick ‘Obtain IP address automatically
- Click •rest1, if •oK’ is displayed, the network is connected successfully.
Note: Please ensure DHCP in your router is open.
Download 20S1 Smart App
View on PC Client
AVSS client can be applied to DVR/NVR/IPC monitoring, with functions such as
live view, device management, and remote video playback etc .. Make sure that
the device has completed the network configuration before adding device on PC
client.
Download and install the AVSS client.
Official Download: www.zositech.com
Login
Install and open AVSS client, select the language and click Login.
NOTE: Please register first if you don’t have an account.
It is recommended to log in with the account of ZOSI Smart App to avoid
multiple accounts, or choose local login (no account and password is
required).
Device Management
Click Add Device below the device list to add device information.
Select device type: NVR/DVR/IPC, etc., enter device name, device ID or instant
identifier ID (Drag the device QR code or sharing code into the QR Code
Identification Zone), user name, device
password and channel amount, and save the information.
NOTE: The default user name is “admin”, the default password of IPC is
“admin”, NVR/DVR does not need to enter a password, the number of camera
channels should be the number of cameras, the default is “1”.
Live View
Select the device on “Live” page and watch live streaming.
Video Playback
Select device, channel, date and time on “Playback” page, click the play
icon to start replaying recorded footage.
Preview
Click “Preview” > Device List > select corresponding device > click the right
mouse button > select “Play All”, “Stop All” in the menu to complete the video
preview display and close.
Connect the Device
If you buy the wireless camera and NVR in a package,the wireless camera is
added to the NVR by default, you can see video when power on.
If you buy wireless Camera and NVR seperately,then you need to add the device
manually, do it as following,
-
Connect the NVR and camera by RJ-45 cable,
-
Enter the NVR interface, right click the mouse, select “IPC Channel Config”.
-
Click “Search”, PoE camera IP address is displayed, then click “Connect Automatically” to add the camera to NVR system
-
Wait about 5 seconds,camera would be added to NVR channel sucessfully
-
Unplug RJ-45 cable from the added camera, and connect it to another wifi camera, then do it as step 3 to step 6 as above.
Install a Hard Disk
The system may not include Hard Disk, it’s depending on the kit you selected.
This system works with most 3.5″ SATA Hard Disk or 2.5″ SATA Hard Disk.
Note: if your system has preinstalled hard disk, please skip this step.
- Unplug your NVR from power, unscrew and remove the top cover.
- Connect the SATA power and data cables from the NVR to the corresponding ports on your hard disk as shown.
- Place the hard disk into the NVR. Any cable should cross up over the hard disk.
- Holding the hard disk and the NVR, gently turn it over and line up the holes on the hard disk with the holes on the NVR. Using a Phillips screwdriver, screw the provided screws into the holes. Assemble the cover.
Note:
After installing a hard disk, you need to first format the Hard Disk before
recording.
Right click the mouse> go to Main Menu> Disk Management> Select the Hard Disk>
Click Format> Apply.
Video Record
Right click mouse> Go to Main Menu> Setup> Record
You shall see the record settings for all channels. Change the record setting
according to your preference and apply the changes.
Motion Detection
Set motion Detection,NVR will record only when motion or movement is detected.
Right click mouse> Main Menu > Setup> Alarm> Motion > Motion detection.
The system starts recording when motion is detected by the camera, and the
monitoring picture will show at the bottom left corner.
Note: if your system has preinstalled hard disk, please skip this step.
Select Camera. Tick the Channel you want to record on motion detection.
Area: It is allowed to set sensitivity area of camera viewing range.
- Click STAR to make the whole viewing range as sensitivity
- Click Trash Box to remove sensitivity area
- Click to save setting
- Click to exit
As Color and luminance Is Important for sensitivity, so it’s necessary to
adjust Its value at specific conditions. The default value is 6 while value
range is from 1 to 8.
Right-click mouse to show or hide control menu at screen bottom.
Test the setting by moving something or someone walk through grid area within
camera view range. If NVR detects movement within grid area, a red hunanoid
figure would be presented in the screen. The grid shall not cover flag,trees
or some other flying objects in the wind to avoid false alerts.
Scheduled Record
Set Time scheduled record, you may configure each channel to record at
specific times based on time of day.
Right click the mouse > go to Main Menu >Setup> Schedule
- Using the pencil tool to highlight the individual hours for specific days.
- Using the adjacent eraser tool removes the highlighting in a block.
Settings can be copied and applied to any or all of the channels and to any other day.
Blocks of time to be recorded can also be set up by double clicking on a field adjacent to a day. Multiple schedules can be created and saved with start and stop times down to the minute. These can then be applied to multiple days and cameras.
Video Playback
Get into system Main Menu > Search, system presents as following:
Search the video you want via time or Event, then play it.
Previous Record: Move to last recorded event
Next Record: Move to next recorded event
Fast Forward: video can be played at different speed, from 1/4 times to 16
times.
Rewind: Video play can be rewinded at 1 time, 8 times, 16 times and 32
times.
Screen Display Mode: Both single-screen and multi-screen are available.
You can choose how many channels you want to playback one time.Channel without
records presents blank screen.
Video Backup
- Plug an USB flash disk into your NVR’s USB port
- Right click the mouse> Main Menu> Backup> choose the channel and time period > Search > Choose the video clips you want to backup> Click Backup
FAQs
Q: Why can’t I search for devices when adding?
A: Make sure that the device and the mobile device are on the same LAN,
otherwise please enter the device ID manually;
Q: Why can’t my device connect to the network?
A: Please check
- Is the device connected to the Internet?
- Is the router working properly?
- Is the router’s DHCP server open?
Q: Why can’t I find the video files?
A: Please check
- Is the hard drive broken?
- Is the search period valid?
- Whether the equipment system time is correct
Q: Why the monitor screen cannot display for some channels?
A: Please check
- Has the camera been added to the NVR?
- Is the camera too far away from the NVR?
- Is there a metal mesh or thick wall near the camera?
- It is recommended to use an extended antenna to bypass obstacles
WARNING
Do not ingest battery, Chemical Burn Hazard.
This product contains a coin/ button cell battery. If the coin/ button cell
battery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and
keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
CAUTION:
Risk of explosion if the battery is replaced by an incorrect type.
www.zositech.com
service@zositech.com
All rights reserved. No part of this publication may be reproduced by any
means without written permission from ZOSI. The information in this
publication is believed to be accurate in all respects.
ZOSI cannot assume responsibility for any consequences resulting from the use
thereof. The information contained herein is subject to change without notice.
Revisions or new editions to this publication may be issued to incorporate
such changes.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>