Menuett 006137 Shoe Dryer Instruction Manual

Menuett 006137 Shoe Dryer Instruction Manual

SAFETY INSTRUCTIONS

• The product must only be used for its intended purpose and in accordance with these instructions.
• The product is only intended for household use.
• Never cover the product with laundry or other objects.
• The hot exhaust vent must not be blocked.
• The power cord must not be in contact with the product during use.
• Check that the mains voltage corresponds to the rated voltage on the type plate.
• Do not use the product near bath tubs, showers, wash basins, or pools, etc.
• Never immerse the product in water or any other liquid. Pull out the plug immediate-ly if the product comes into contact with water.
• Do not use the product if it is damaged or not working properly, or if the power cord or plug are damaged. Take the product to an authorized service centre to be checked, repaired or adjusted.
• Do not put the product near a hot stove or hot oven.
• The product is not intended to be used by persons (children or adults) with any form of functional disorders, or by persons who do not have sufficient experience or knowledge on how to use it, unless they have received instructions concerning the use of the product from someone who is responsible for their safety.
• Keep children under supervision to make sure they do not play with the product.
• This product can be used by children from 8 years and upwards if they are super-vised or receive instructions concerning the safe use of the product and understand the risks involved. Do not allow children under 8 to use, clean or maintain the product without supervision.

SYMBOLS

|

Conforms with the requirements in the relevant EU directives

---|---

| Recycle as electrical waste
|

Safety class II

TECHNICAL DATA

• Rated voltage: 220-240 V — 50 Hz
• Output: 350 W
• Noise level: 49 dB
• Size: W 220 x H 290 x D 100 mm
• Cord length: 1.3 m
• Hose length: 0.65 m

DESCRIPTION

1. Timer
2. Status light
3. Thermostat
4. Hose
   BILD 1

INSTALLATION

1. Drill 3 holes in the wall (fig. A and B) , diameter 8 mm, depth 40 mm.
2. Put plugs into the holes (fig. C) and screw in the screws so that the screw heads extrude about 3-5 mm from the wall (fig.  D ).
3. Hang the shoe drier on the screws (fig. E).
4. Secure the shoe drier by screwing on the metal plate (fig. F).

BILD 2

1. Hole
2. Screwdriver
3. Screw
4. Screw plug
5. Hole
6. Screw
7. Wall
8. Screwdriver
9. Screw
10. Metal plate

OBS!

Make sure to use the right screws and plugs, depending on the wall material.

USE

1. Plug in the plug.
2. Place the hoses in the damp boots or shoes.
3. Set the thermostat knob to max. Turn the timer knob to the required time. The shoe drier starts and the status light goes on.
4. The status light stays on while the shoe drier is running.
5. The shoe drier switches off when the timer knob returns to OFF. To continue drying the shoes, turn the timer knob again.

OVERHEATING PROTECTION

The overheating protection automatically switches off the shoe drier in the event of overheating. Follow the instructions below if the overheating protection trips.

1. Pull out the plug.
2. Remove the cause of the overheating (e.g. obstruction of air flow, fluff etc.).
3. Allow the shoe drier to cool for a few minutes. Start the shoe drier again.

MAINTENANCE

CLEANING

Check the shoe drier at regular intervals.

• Pull out the plug and check if there is any dust or fluff in the shoe drier.
• Clean the outside of the shoe drier with a damp cloth, and vacuum clean the grille if necessary.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>