JLL Fitness CT500 Elliptical Cross Trainer Monitor Installation Guide
- June 9, 2024
- JLL Fitness
Table of Contents
INSTRUCTION GUIDE
CT500 MONITOR
COPYRIGHT
The contents of this manual are subject to change without notice to improve
quality.
© 2023 JLL Fitness Ltd
JLL Fitness Ltd owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the
authorization of JLL Fitness Ltd is prohibited.
SAFETY PRECAUTIONS
The monitor on this machine has been tested to the required standards, each of
those passed regulations are shown via the following symbols:
WEEE – Waste Electrical and Electronic Equipment Recycling.
ABS – Acrylonitrile Butadiene Styrene often referred to as ABS is a type
of plastic that is an opaque thermoplastic.
CE – The product conforms with relevant EU directives regarding health
and safety or environmental protection.
QC Pass – A product which has fulfilled the requirements of a technical
control and passed the outgoing exams.
ROHS – This is an abbreviation for “Restriction of (the use of certain)
Hazardous Substances in electrical and electronic
CLEANING
Please take care when cleaning this monitor as the LCD screen can easily be scratched.
You will need a soft dry cloth|
---|---
Do not spray cleaning chemicals directly onto the monitor|
Do not apply water to the monitor as it is electrical and may damage the
internal components|
INSTALLATION
**STEP 1
| STEP 2**
---|---
Insert the batteries, making sure they are the correct way round.| Remove the
four screws from the back of the monitor.
STEP 3
| STEP 4
Connect the male to female wires from the base to the monitor.| Secure the monitor to the base using the four screws previously removed.
OPERATION
The CT500 monitor has a total of 6 readouts, displaying:
Time Speed Distance Heart Rate Calories Odometer
When first powered on, the monitor will automatically be in `Scan’ mode.
This means the digits in the largest segment on the screen will change every
few seconds between time, distance, speed etc. This will allow you to have an
overview while training without pressing any buttons. When the machine is in
use you will also see a cycling icon in the top left corner, when you stop
exercising the icon will disappear.
EXITING SCAN MODE
Press `MODE’ to exit scan mode and continuously press it to view each readout. If you are within scan mode, there will be a scan icon in the bottom left to indicate this.
SETTING TARGET PROGRAMS
On this monitor your are able to set a target time, distance, pulse and calories.
- Start by pressing `MODE’ until your chosen setting flashes.
- Then press `SET’ to change the digits to your desired target.
- Once set, begin your workout by pedalling and you will see the digits begin to change.
RESETTING YOUR MONITOR
Press and hold the `RESET’ button until all the digits come up and return to zero,
DATA READOUTS
| Readout | Measurement |
|---|---|
| Time | Minutes : Seconds |
| Speed | KM/H |
| Distance | Kilometres |
| Pulse | BPM (Beats Per Minute) |
| Odometer | Kilometres |
TROUBLESHOOT
| Issue | Resolutions |
|---|---|
| No power to the monitor | • Make sure the batteries are fully inserted and the |
correct way round.
• Check your connection wires from the monitor to the base. They must not be
trapped, fully connected and the pins must be straight.
No pulse reading| • Make sure the pulse plates are clean and dry.
• Do not have any lotion on your hands.
• Sweat can affect the reading.
• Make sure both hands are fully gripping each plate.
CONTACT DETAILS
| Tel: 0121 328 7507
---|---
| Email: info@jllfitness.co.uk
| Live Chat: WWW.JLLFITNESS.CO.UK
@JLLFITNESS
Documents / Resources
| JLL
Fitness CT500 Elliptical Cross Trainer
Monitor
[pdf] Installation Guide
CT500, Elliptical Cross Trainer Monitor, CT500 Elliptical Cross Trainer
Monitor, Cross Trainer Monitor, Trainer Monitor
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>