Baby Factory Edinburgh Child Car Seat Instruction Manual
- August 22, 2024
- Baby Factory
Table of Contents
- Baby Factory Edinburgh Child Car Seat
- SAFETY WARNING
- Install position of the child seat in vehicle
- Headrest adjustment 05.2 Seat angle adjustment
- Adjust the ISOFIX attachments
- INSTALLATION
- Maintenance and cleaning
- The main technical parameters
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Baby Factory Edinburgh Child Car Seat
Distributed by
Baby Factory (NZ) ltd
58 Stonedon Drive
East Tamaki Auckland NZ
www.babyfactory.co.nz
Super Ride size Booster
INSTRUCTION MANUAL
CHILD CAR SEAT
Height: 100-150cm Weight: 15-36 KG
SAFETY WARNING
-
This product can be used also be forward-facing for children with a height of 100-150cm (Weight: 15-36kg, about 3-12 years old), using adult three-point belt to fix the child restraint system, or using ISOFIX and adult three-point belt together to fix the child restraint system.
-
Do not use any load bearing contact points other than those described in the instructions and marked in the child restraint when in 100-150cm.
-
Please keep for furture reference.
-
Do not use this child restraint at home. It has not been designed for home use and should only be used in your car.
-
For the reason of safety, the child restraint must be fixed inside the vehicle using ISOFIX anchorages even if you do not put your child inside the child seat.
-
Any straps holding the restraint to the vehicle should be tight ;
-
Any straps restraining the child should be adjusted to the child body ;
-
Straps should not be twisted ;
-
Ensure that any lap strap is worn low down, so that the pelvis is firmly engaged, shall be stressed ;
-
The device should be replaced when it has been subject to violent stresses in an accident ;
Follow closely the installation instructions provided by the manufacturer ; -
Don’t leave your child in the child restraint unattended.
-
Any luggage or other object liable to cause injuries in the event of a collision shall be properly secured ;
-
The ECRS shall not be used without the cover ;
-
The seat cover should not be replaced with any other than the one recommended by the manufacturer, because the cover constitutes an integral part of the restraint performance
-
The instructions shall be retained on the device for its life period or in the vehicle handhook in the case of built-in restraints
-
The user shall also be referred to the vehicle manufacturer’s handhook ;
-
Never use a second-hand product , as you can never be certain what was happened to it.
NOTICE
- i-Size booster seats ECRS (100-150cm )
- Notice
- This is a i-Size booster seat Enhanced Child Restraint System. It is approved according to UN Regulation No.129, for use primarily in *I-Size seating position” as indicated by vehicle manufacturers in the vehicle user’s manual.
- If in doubt, consult either the Enhanced Child Restraint System manufacturer or the retailer.
Install position of the child seat in vehicle
- Only suitable if the approved vehicles are fitted with 3 point safety-belt, approved to UN/EGE Regulation No.16 or other equivalent standards.
- Do not use in seating positions where an active frontal airbag is installed.
- The child restraint system can only be installed in this position with an ISOFIX anchorage or an adult three-point seat belt.
Headrest adjustment 05.2 Seat angle adjustment
Headrest adjustment:
Press and hold the blue button on the backrest, and pull the groove on the
back of the headrest. The headrest has 8 gears which can be adjusted depending
on the child’s height.
Seat angle adjustment:
Lift the bottom end of the seat and adjust the shifter to the front. If you
want to retract it, just move it in the opposite direction.
Adjust the ISOFIX attachments
- The ISOFIX attachments can be adjusted for many positions to fit the different positions of ISOFIX low anchorages expending from child_ restraint.
- Press down the release button to adjust ISOFIX attachment of both sides to the longest. Then put the ISOFIX attachments into guide sleeves, and insert them into ISOFIX anchorages. Make sure that you have heard a “click” and the ISOFIX latching indication shows GREEN. If you want to release the ISOFIX attachments, just installation of the ISOFIX attachments is finished. Push the release button of the ISOFIX chuck at the direction as shown, the ISOFIX chuck will be released. After installed the ISOFIX chuck, push the child restraint forwards until it is tight against the car seat. Now, the
- ISOFIX base is installed in place.
INSTALLATION
Method 1 ISOFIX+3-POINT BELT
Place the child restraint on the car seat and at the same time ISOFIX locks
the car ISOFIX interface (see 06), when you hear “KA”, the release button is
green, Make sure close to the car seat; Then place the child on the child
restraint, insert the car seat belt across the child’s body into the car
groove of the car seat; Make sure that the car seat shoulder belt passes
through the guide groove of the headrest, and pull up the car seat lap belt to
check whether it is locked
Method 3-POINT BELT
Place the child restraint on the car seat, close to the car seat; Then place
the child on the child restraint, insert the car seat belt across the child’s
body into the car groove of the car seat; Make sure that the car seat shoulder
belt passes through the guide groove of the headrest, and pull up the car seat
lap belt to check whether it is locked.
After belt fixed, the seat buckle and belt guide hook can not be placed in
this position. Please contact the manufacturer if in doubt.
Maintenance and cleaning
Daily maintenance
- In daily use, check the child restraint periodically. The child restraint should be replaced after an accident.
- Please keep this child restraint in dry and ventilated place to avoid damp moldy. If the child restraint becomes dusty, clean the seat belt and the plastic pieces by swiping them with a damp sponge and let it dry under ambiance. If food or drink drop accidently on the buckle, disassemble the seat belt from the child restraint and rinse it gently by warm water. Leave it dry under ambiance.
- For cleaning the entire child restraint fabric cover, please refer to the washing instruction.
Washing instruction
Never use any solvent, chemical detergent or lubricant on any part of your
child seat..
The main technical parameters
- Distance from front to back of the seat:450mm
- Distance form left to right of the seat:439mm
- Height of the seat:595mm
- Weight of the seat:5.6±0.5kg
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>