Menuett 003-284 Steam Cleaner Instruction Manual

June 6, 2024
Menuett

003-284

STEAM CLEANER
OPERATING INSTRUCTIONS Important! Read the user instructions carefully before use. Save them for future reference. (Translation of the original instructions).

Care for the environment! Recycle discarded products in accordance with local regulations.
Jula reserves the right to make changes. For the latest version of operating instructions, see www.jula.com

SAFETY INSTRUCTIONS

  • This steam cleaner can be used by children from eight years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge if they are supervised or receive instructions concerning the safe use of the steam cleaner and understand the risks involved with its use. Do not allow children to play with the steam cleaner. Cleaning and maintenance must not be carried out by children unless they are more than eight years old, and are kept under supervision.
  • Keep the steam cleaner and its power cord out of the reach of children under eight years of age.
  • Keep children under supervision to make sure they do not play with the steam cleaner.
  • Do not expose the power cord or plug to water or other liquids — the risk of electric shock.
  • Check that the power cord and plug are intact and undamaged. Do not use the steam cleaner if the power cord or plug is damaged. If the power cord or plug is damaged they must be replaced by a qualified technician to ensure that the appliance is safe to use.
  • The steam cleaner is only intended for household use. It is not intended for industrial use.
  • Do not start the steam cleaner without water in the reservoir.
  • Check that the mains voltage corresponds to the rated voltage on the type plate.
  • During use, the opening for the reservoir must be sealed and the safety cap must be properly tightened.
  • The steam cleaner only is connected to an earthed powerpoint.
  • An extension cord must be earthed and double insulated.
  • The steam cleaner must not be tilted more than 45 degrees during use. Otherwise, there is a risk of boiling water spraying out with the steam.
  • Do not point the nozzle at people, animals, or electrical equipment.
  • Pull out the plug before filling it with water. Always unplug the plug after use and before cleaning and repairs.
  • Do not pour rust remover, odor remover, alcohol, or detergent in the reservoir—this could damage it.
  • Do not use the steam cleaner to clean swimming pools or the equivalent.
  • Do not point the jet at the equipment that contains electrical components, such as the inside of an oven.
  • Do not overfill the reservoir — the risk of overpressure.
  • Never leave the steam cleaner unattended when it is connected to the mains.
  • Do not use the steam cleaner if it has been dropped, if it is visibly damaged, or is leaking.

SYMBOLS

| WARNING: Risk of scalding
---|---
****| WARNING: Hot surface

TECHNICAL DATA

Power supply 220-240 VAC, 50/60 Hz
 Earthed connection 10 A fuse
 Working pressure 3 bar
Volume  400 ml
Output 1050 W
 Range 5m
Dimensions W15xH31xL24 cm
 Weight 10.7 kg

DESCRIPTION

  1. Window cleaner
  2. Cleaning cloth for textile cleaner
  3. Textile nozzle
  4. Funnel
  5. Measuring cup
  6. Connector for nozzle
  7. Lid
  8. Steam button
  9. Power switch
  10. Status light
  11. Nozzle for the extension tube
  12. Extension tube x 3
  13. Floor nozzle with a microfibre cloth
  14. Connector for nozzle (for extension tube)
  15. Jet nozzle
  16. Angle nozzle
  17. Brush nozzle
  18. Steam cleaner
  19. Flexible nozzle FIG. 1

ASSEMBLY

Unpack the steam cleaner, check that all the accessories are included and that the steam cleaner and accessories are undamaged.
FITTING ACCESSORIES
Fitting options. FIG. 2
Extension tube

  1. Connect the extension tubes together or with the floor nozzle by aligning the catches and pressing them into place. FIG. 3
  2. Release by pressing in the catches and pulling apart.

Conned the nozzle to the connector.

  1. Fit the nozzle on the connector by aligning the pins in the connector and twisting it in place clockwise. FIG. 4
  2. Remove the nozzle by twisting it anticlockwise and pulling loose.

Angle or brush nozzle

  1. Press the nozzle on the jet nozzle or the flexible hose.
  2. Twist the nozzle to the required angle.
  3. Remove the nozzle by pulling it straight out.

Window dewier

  1. Hook the textile nozzle to the window nozzle hooks and click the nozzles together. FIG. 5

USE

NOTE:

  • Protection from overheating with an empty reservoir. When all the water in the reservoir has evaporated the power supply is automatically cut to prevent the empty reservoir from heated up more.

  • The steam cleaner has a thermostat to ensure that the steam stays at 135°C when disinfecting and sterilizing.

  • The safety valve automatically relieves any overpressure. The valve opens automatically and relieves the overpressure when there is high steam pressure in the reservoir.
    INTENDED USE
    The steam cleaner can be used for cleaning doors, windows, floors, and clothes.
    FILLING WITH WATER
    WARNING!

  • The safety cap must not be opened when the reservoir is pressurized.
    NOTE:

  • The reservoir holds 400 ml. Do not pour in too much water as there must be some space left in the reservoir.

  1. Place the steam cleaner on a level surface.
  2. Push down the safety cap and twist it anticlockwise.
  3. Fill the beaker with fresh water and use the funnel to fill the reservoir.
  4. Replace the safety cap and tighten it firmly.

STARTING

  1. Plug the plug into a PowerPoint.

  2. The steam cleaner is ready to use after four minutes.

  3. Push the start inhibitor forward and carefully press the steam button and check that steam comes out from the nozzle.
    — If steam comes from the nozzle release, the steam button fits the required accessory.

  4. Press the steam button to do the job.

Filling with water during use

  1. Pull out the plug from the PowerPoint.
  2. Press the steam button until steam no longer comes out.
  3. Slowly release the safety cap, but let it remain in place until steam no longer comes out.
  4. Place the steam cleaner in a cool place for about five minutes to cool. Now remove the safety cap.
  5. Use the funnel and measuring cup to fill the reservoir with cold or warm water.
  6. Replace the safety cap and tighten it firmly.

FUNCTIONS
Disinfection and sterilization

  1. Fit the jet nozzle or the flexible nozzle on the connector.
  2. Point the nozzle at the surface to be disinfected.
  3. Start the steam cleaner according to the instructions.

Cleaning textiles

  1. Fit the textile nozzle on the connector and slip on the cleaning cloth.
  2. Point the nozzle at a hung garment.
  3. Start the steam cleaner according to the instructions.
  4. Move the brush nozzle up and down and side to side to remove stains from the clothes.

Cleaning windows

  1. Fit the window nozzle onto the textile nozzle.
  2. Start the steam cleaner according to the instructions.
  3. Point the nozzle at the window, and start the steam cleaner according to the instructions.
  4. Move the nozzle up and down and side to side to remove stains.

Cleaning floors Floor nozzle

  1. Lift up the short sides on the floor nozzle and slip-on or remove the microfibre cloth.

  2. Push down the short sides. FIG. 6
    — The microfibre cloth can be used on the brush nozzle for cleaning hard surfaces.
    — To clean carpets, curtains, and sensitive textiles, set the lever on the brush nozzle to the position where the bristles are shortest.

  3. Start the steam cleaner according to the instructions.

  4. Point the nozzle at the floor and press the steam button to remove dirt and stains from the floor and corners.

Angle or brush nozzle

  1. Fit the angled nozzle or the round brush nozzle on the extension nozzle.
  2. Start the steam cleaner according to the instructions.

AFTER USE

  1. Pull out the plug when the steam cleaner is not in use.
  2. Press the steam button until steam no longer comes out.
  3. Slowly release the safety cap, but let it remain in place until steam no longer comes out.
  4. Place the steam cleaner in a cool place for about five minutes to cool. Now remove the safety cap.
  5. Empty the reservoir and wipe the steam cleaner with a dry cloth.
  6. Replace the safety cap and tighten it firmly.

MLA Aft BOX 363, SE-532 24 SKARA
2022-01-19
© Jula AB

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals