Commercial Electric 568051410 2 ft. Low Profile Easy Install Wrap with Pull Chain User Guide

Commercial Electric 568051410 2 ft. Low Profile Easy Install Wrap with

Pull Chain

Safety Information

• WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal.
• WARNING: Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
• CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warranty

WHAT has COVERED  The manufacturer warrants this light fixture to be free from defects in materials and workmanship for a period of five (5) years from
date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling.

WHAT IS NOT COVERED This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product. Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.

PLANNING INSTALLATION

Before beginning assembly, installation, or operation of product, make sure all parts are present. Compare parts with the Hardware Included and Package Contents lists. If any part is missing or damaged, do not attempt to assemble, install, or operate the product. Contact Customer Service for replacement parts.

NOTE: Keep your receipt and these instructions for proof of purchase. If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.

TOOLS/HARDWARE REQUIRED

Tools and hardware required vary by type of installation.

PACKAGE CONTENTS

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

Select a suitable location that can support the weight of the fixture. Determine the method for mounting the fixture before drilling, based on the type of ceiling.

WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker before removing an existing light fixture or installing the new one. With power disconnected to the electrical box, remove the existing fixture. Make a sketch of how the current fixture is wired (by wire color) or mark the wires with masking tape and a pencil so you will know how to properly reconnect the wires to the new LED light fixture.

1. Marking the mounting location
   • With help from another person, temporarily hold the fixture body (A) up to the ceiling to determine the best mounting position and which knock out hole to use for wiring the fixture.
   • Mark two keyhole locations on the mounting surface. The distance between the two keyholes is 23.2-in(589mm).
2. Making the electrical connections
   • Insert the hot and neutral wires from the electrical box into the wire connectors of the black and white wires from the fixture body (A).
   • Insert the ground wire from the electrical box into the wire connector of the green wire from the fixture body (A).
   • Wrap the wires with electrical tape for a more secure connection.
   • Position the wires back inside the electrical box.
3. Attaching the housing to the ceiling
   • Drill a 1/4-in. pilot hole into each of the screw locations marked on the ceiling. You can also use an awl or nail to dimple the screw holes.
   • Install a drywall anchor (AA) and a mounting screw (BB) in each drilled mounting hole, but do not tighten fully.
   • Align the 2 mounting keyholes on the fixture body (A) with the 2 mounting screws (BB) in the ceiling. Once the screw heads are through the large ends of the keyholes, slide the fixture body (A) until the heads of the mounting screws (BB) slide into the narrow ends of the keyholes.
   • Finish tightening the mounting screws (BB) until the fixture body (A) is tightly secured to the mounting surface.
   • Pull the chain down to turn the light on and off.
     NOTE: The drywall anchors (AA) are only to be used for mounting the fixture to plaster or drywall surfaces.

Care and Cleaning

CAUTION: Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box.

• Clean the fixture with a soft, dry cloth.
• Do not use cleaners with chemicals, solvents, or harsh abrasives.
• Do not use liquid cleaner on the LEDs, LED driver, or wiring inside the light fixture.

Troubleshooting

WARNING: Before doing any work on the fixture, disconnect power to the light fixture. Minor problems often can be fixed without the help of an electrician.

Contact a qualified electrician.
There is a defective switch.| Contact a qualified electrician.
The fuse blows or the circuit breaker trips when the light is turned on.| The wires are crossed or the power wire is grounding out.| Check the wire connections.

Contact a qualified electrician or call Commercial Electric customer service 1-877-527-0313.

Light distribution

1. Maximum Candela = 720.625
2. Located At Horizontal Angle = 0, Vertical Angle = 0
3.  Vertical Plane Through Horizontal Angles (0-180) # 2 – Vertical Plane Through Horizontal Angles (90-270)
4. Questions, problems, missing parts? Before returning to the store, call Commercial Electric Customer Service 8 a.m.-6 p.m., EST, Monday-Friday 1-877-527-0313
5. HOMEDEPOT.COM Retain this manual for future use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>