livington MagiCut 6-in-1 Power-Multi-Zerkleinerer Instructions
- June 6, 2024
- LIVINGTON
Table of Contents
livington MagiCut 6-in-1 Power-Multi-Zerkleinerer
**Scope of delivery and description of the parts
**
- A. 1 x Livington MagiCut motor unit
- B. 1 x collecting container 1000ml
- C. 1 x collecting container 360ml
- D. 1 x lid for the collecting container (360ml), including seal
- E. 1 x lid for the collecting container (1000ml), including seal
- F. 2 x blade attachment with 2 blades
- G. 2 x additional blade for blade attachment (pre-assembled)
- H. Shaft for stirring and beating attachment (pre-assemb-led emulsifying attachment)
- I. Emulsifying attachment
- J. Beating attachment
- K. Metal pin in the collecting container
- L. Power button
- M. Locking valve on the lid
SAFETY NOTICES
- The device should only be used by children aged 8 years and over, as well as by persons with reduced physical, sensory or mental abilities or lack of experience and knowledge if they are supervised or have been instructed on the safe use of the device and understand the dangers associated with its use. Children must never be allowed to play with the device. Cleaning and user maintenance should not be performed by children unless they are above 8 years of age and supervised. Children under the age of 8 must be kept away from the device and the connecting cable.
- Before switching on, make sure that the electrical voltage and frequency of the circuit match those on the device‘s rating plate.
- To reduce the risk of electric shock, the motor unit, power cord, and plug must not be immersed in water or other liquids or rinsed under running water.
- The device is not suitable for operation with an external timer or remote control.
- Use only accessories recommended by the manufacturer, otherwise, fire, electric shock or injury may arise.
- Never operate the device without ingredients inside, as this could damage the device.
- Never fill the collecting container above the ‚Max.‘ mark. This could lead to serious damage to the device.
- DO NOT pull the cable, do not carry the device by the cable, do not squeeze the cable in doorways, do not pull the cable around sharp edges or corners, and keep the cable away from hot surfaces. DO NOT bend or damage the power cord.
- Do not use the device if the power cable, plug or other parts of the device are damaged. Contact an authorized service centre if inspection, repair or adjustment is required.
- Unplug the device from the wall outlet when it is not in use.
- DO NOT move or lift the device while it is still plugged in or turned on. Always make sure that the device is switched off before moving it.
- DO NOT leave the device unattended when it is in operation.
- DO NOT place the device near a hot gas or electric stove.
- Wait until the device has come to a complete standstill before removing the cover or other parts.
- The device is free from parts that require user maintenance. Do not repair, disassemble or modify the device.
- To avoid injuries or damage to property, use the product only as described in these operating instructions.
- Do not make any unauthorized modifications, repairs or changes to the device.
- Never place the device on hot surfaces or near open flames.
- Never allow hands, hair, loose clothing or other objects to come into contact with the blades.
- The blades are extremely sharp, in order to achieve an optimal cutting result. Always use with caution.
- Not suitable for preparing soups or large quantities of liquid ingredients.
BEFORE FIRST USE
Remove all packaging material and rinse the container, storage lid and
attachments by hand with warm water and a mild detergent. Wipe the main unit
with a damp cloth.
ASSEMBLING THE ATTACHMENTS
Blade attachment
When you receive the product, the two additional blades come pre-assembled on the blade attachment. If you want to disassemble the blade attachment, e.g. to use only 2 blades, turn the upper two additional blades in a clockwise direction. Proceed as follows to assemble and use the attachment:
- 1. Place the two additional blades on the shaft of the blade attachment. Place the pins of the additional blades in the guide rails on the shaft and tighten the additional blades at the end of the shaft in an anti-clockwise direction. To remove the blades, carry out these steps in reverse. Note: The blades are very sharp! Handle carefully, to avoid injuries. NOTE: The blade insert is not suitable for chopping (cooking) chocolate
Emulsifying attachment
- When you receive delivery of the device, the emulsifying attachment should come pre-assembled on the shaft. If this is not the case, place the emulsifying attachment on the shaft with the pins facing downward. Align the pins with the guide rails on the shaft and tighten the attachment at the end of the shaft in an anti-clockwise direction.
Beating attachment
- Unscrew the emulsifying attachment from the shaft if it is pre-assembled.
- Place the beating attachment on the shaft with the pins facing down. Align the pins on the guide rails on the shaft, and tighten the attachment at the end of the shaft.
**USE
**
- Assemble the attachment required as described above.
- Place the container on a flat, slip-proof surface.
- Place the attachment on the metal pin inside the container.
- Now fill the container with the desired ingredients (do not fill above the Max. mark!)
- Close the container with the storage lid (with the white cap facing up). The shaft of the attachment must protrude through the hole in the middle of the lid. CAUTION: NEVER USE WITHOUT the LID being attached. Note: when using for the first time, please insert the seal on the rim of the lid into the guide rail on the lid.
- Now attach the motor unit, paying attention to the guide rails on the cover and the main unit.
- Now connect the device to a power outlet.
- Press the power button on the device. The process will be performed until you release the button. Press the power button repeatedly at short intervals until the desired consistency is reached.
TIPS
- Hold the receptacle while pressing the power button to ensure that the device stays in place.
- DO NOT operate the device for more than 15 seconds at a time.
- Warning : Do not leave activated for an excessive period of time. For more coarsely chopped foodstuffs, press the power button repeatedly in a pulsating manner until the desired consistency is achieved.
- For best results, repeatedly press the power button for brief periods.
- Make sure the blades have stopped completely and the device is disconnected from the mains before removing the motor unit.
- For airtight storage of foodstuffs, you can close the lid with the valve.
CLEANING
ALWAYS UNPLUG THE DEVICE FROM THE WALL OUTLET BEFORE CLEANING.
Wash the container and attachments immediately after use, either with warm
water or in the dishwasher. Wipe the main body with a damp cloth. Do not
immerse it in water.
Note: Do not use chemical, steel, wood or abrasive cleaners to clean the
device, to prevent alterations to its surface and/or other damage.
TROUBLESHOOTING
The Livington MagiCut is a simple and easy-to-use device. If you observe the
care and maintenance instructions given above, trouble-free use should be
possible. If you experience any problems, please refer to the „Frequently
Asked Questions“. If the issue cannot be solved by referring to these, please
contact our customer service by phone or email (see address on the back).
FREQUENTLY ASKED QUESTIONS
Issue: The device will not switch on.
Solution: Please check that the power cable is correctly connected and
that the collecting container, motor unit and attachments are correctly
engaged. The device only works if the motor unit is fully and correctly
fitted.
Issue: The device suddenly stops working.
Solution: The container is overfilled and may block the device. This can
be prevented by observing the maximum filling quantity.
Question: Can all removable parts be washed in the dishwasher?Answer:
Yes, with the exception of the motor unit.
Question: Why does the motor produce an unpleasant smell when working?
Answer: New devices often give off an unpleasant smell or emit some smoke
during the first few uses. This will cease after a few uses. The device can
also emit an unpleasant smell or smoke if it has been used for an excessive
period of time. If this occurs, you must switch off the device and allow it to
cool down for 60 minutes.
TECHNICAL DATA
220-240V ~ 50Hz 300W
Technical and optical changes reserved.